Arecont Vision MegaDome 2 Manuale utente

Arecont Vision MegaDome®Installation Manual

0 | Page

Arecont Vision MegaDome®Installation Manual

1 | Page

MegaDome®2 Installation Manual

A. Arecont Vision MegaDome®2

Inside the box:

B. Mounting template

C. AC & DC Power cable

D. One double sided hex key

E. One single sided hex key

F. Security L-key

G. Pack of four (4) wood screws and four (4)

dry wall anchors

H. I/O cable

•#1 Phillips head screw driver

Not included but needed:

•#2 Phillips head screw driver

Image 1

Mounting the Camera:

1. Remove camera and hardware from the box.

2. Using the Mounting template, prepare the

mounting provisions for camera installation.

NOTE: the 19.5mm diameter hole on the

Mounting template is where the Ethernet

cable will be exiting the MegaDome®, align

accordingly. If using the side conduit hole,

please see step 7below.

3. Using Security L-key, loosen the four (4)

screws securing the dome cover (Image 2).

Remove vandal resistant dome cover. NOTE:

Do not remove screws from the dome cover.

Image 2

GFE

Arecont Vision MegaDome®Installation Manual

2 | Page

4. Run Ethernet cable through the hole on the

bottom of the camera (Image 3) and plug it

into the RJ45 port. NOTE: If the camera will

be powered via PoE, please skip to step 6.

5. If the camera is powered by an outside power

supply, run the supplied power cable through

the hole and connect it to its respective

connector inside the camera (Image 3).

NOTE: Make sure that your installation of

wires complies with Electrical Code of the

local government where the camera is

installed and no bare wires are exposed.

Image 3

6. Align the holes in the camera with the

prepared holes on the mounting surface.

Attach the camera to the mounting surface

with the wood screws or any optional

hardware suitable for the mounting surface.

7. If you are using the side conduit opening,

remove the conduit plug by first removing the

socket set screw using one of provided Allen

keys (Image 4).

Image 4

HOLE

POWER

RJ-45

Arecont Vision MegaDome®Installation Manual

3 | Page

8. To adjust the tilt, use a #1 Phillips screwdriver

to loosen the screw on the side of the plastic

lens bracket 1/4 turn (Image 5). CAUTION:

Do not remove the screw!

Adjusting the Tilt, Pan, Z-axis (yaw):

9. Adjust lens tilt as required and tighten the

screw.

10. To adjust the pan, use a #2 Phillips

screwdriver to loosen the screw as shown in

Image 5.

11. Adjust the pan as required and tighten the

screw.

12. To adjust the Z-Axis, or Yaw, for vertical wall

mounting, loosen the set screw as shown in

Image 5. NOTE: There are two set screws on

opposite sides; both need to be loosened.

13. Adjust the Z-Axis as required and tighten the

set screw back down.

Image 5

Z-AXIS

(yaw)

TILT

PAN

Arecont Vision MegaDome®Installation Manual

4 | Page

14. To adjust Focus or Zoom, open camera web

interface and click the “Focus” button as

shown in image 6.

Adjusting the Focus and Zoom:

15. Set up a focus area by drawing a rectangle

with the mouse (by left-clicking and holding

down the mouse button) shown in Image 7.

16. To automatically adjust focus, choose “Full-

range Focusing” or “Fast Focusing”

depending on the image clarity as shown in

image 7.

- If the image is completely out of focus,

choose “Full-range Focusing” to scan the full

focus range and find the best focus position.

- If the image is slightly of out of focus,

choose “Fast Focusing” to fine tune and

quickly get a precise focus position to save

time.

17. To manually focus, click the “+20”, “+5”, “+1”,

“-20”, “-5”, “-1” buttons to fine tune the focus

position.

18. To manually adjust Zoom, click the “+20”,

“+5”, “+1”, “-20”, “-5”, “-1” buttons to move the

zoom step.

Note: “+” means move from wide to tele end;

“-” means move from tele to wide end.

19. If the “Enable Auto Focus after zoom” option

is checked as shown in image 7, the focus

will automatically be adjusted when zoom is

changed.

18. Remove the protective film from the camera

dome. NOTE: be careful not to scratch the

vandal dome cover.

19. Secure the vandal dome cover to the camera.

20. Click “Fast Focusing” to fine tune and get

precise focus position.

Image 6

Image 7

Arecont Vision MegaDome®Installation Manual

5 | Page

MegaDome®2 Pendant Mount (MD-CMT) Installation Instructions

A. Top shield

Inside the box:

B. Pendant Mount

C. Mounting template

D. Pack of four (4) machine screws

E. Pack of four (4) small machine screws

F. Pack of four (4) wood screws and four (4)

dry wall anchors

G. Large round rubber gasket

H. Smaller square rubber gasket

I. One double sided hex key

J. #2 Phillips head screw driver

Not included but needed:

Image 8

1. Remove Pendant Mount and hardware from

the box.

Image 9Image 10

2. Using the Mounting template, prepare the

mounting provisions for camera installation.

3. Place small gasket onto pendant dome as

shown in image 9.

4. Attach Dome to Pendant as shown in Image

10 using four machine screws provided.

5. Install large round rubber gasket onto

Pendant as shown in image 10. Be sure to

align the holes appropriately.

6. Run Ethernet Cable and outside power cable

(if necessary) through the Pendant.

7. Attach Pendant to the ceiling using the four

wood screws provided or any optional

hardware suitable for the mounting surface.

8. For installation of the camera, please

reference “Mounting the Camera”.

Arecont Vision MegaDome®Installation Manual

6 | Page

MegaDome® 2 Wall Mount (MD-WMT2) Installation Instructions

MD-WMT2 only fits with SV-JBA and SV-EBA but

not with the older MD-JBA and MD-EBA!

Caution:

A. Wall mount

Inside the box:

B. Top shield

C. Mounting template

D. One double sided hex key

E. Pack of four (4) machine screws

F. Pack of four (4) wood screws and four (4)

dry wall anchors

•#2 Phillips head screw driver

Not included but needed:

Image 11

1. Remove Wall Mount and hardware from the

box.

Image 12

2. Using the Mounting template, prepare the

mounting surface.

3. Install Top Shield on Wall Mount as shown in

image 12.

4. Fasten the socket set screw using double side

hex key.

5. Run Ethernet Cable and outside power cable

(if necessary) through the Wall Mount.

6 Attach Wall Mount to the wall using drywall

screws or any optional hardware suitable for

the mounting surface.

7. For installation of the camera, please

reference “Mounting the Camera”.

Arecont Vision MegaDome®Installation Manual

7 | Page

MegaDome®2 Wall Mount Cap (MD-CAP) Installation Instructions

A. Wall Mount Cap (MD-CAP)

Inside the box:

B. Pack of four (4) machine screws

•1½” NPT Pipe nipple

Not included but needed:

•1½” NPT Coupling

•1½” NPT Flange

•#2 Phillips head screw driver

Image 13

1. Remove Wall Mount Cap from the box.

2. Assemble Wall Mount Cap, 1½” Coupling,

1½” Pipe nipple and 1½” Flange as a Pendant

Mount shown in image 14.

Image 14

3. Run Ethernet Cable and outside power cable

(if necessary) through the Pendant.

4. Attach Pendant to the ceiling using four wood

screws or any optional hardware suitable for

the mounting surface

5. For installation of the camera, please

reference “Mounting the Camera”.

MD-CAP

1 ½” Coupling

1 ½” Pipe

1 ½” Flange

Arecont Vision MegaDome®Installation Manual

8 | Page

MegaDome®2 Junction Box Adapter (MD-JBA) Installation Instructions

MD-JBA only fits with MegaDome®2 and MD-CMT

but not with MD-WMT2!

Caution:

A. Junction Box Adapter

Inside the box:

B. Pack of four (4) machine screws

C. Pack of four (4) wood screws and four (4)

dry wall anchors

D. Large round rubber gasket

E. One double sided hex key

•#2 Phillips head screw driver

Not included but needed:

•MegaDome® Wall Mount, MD-WMT

•¾” NPT Conduit (if necessary)

Image 15

1. Remove Junction Box and hardware from the

box

Image 16Image 17

2. Remove the conduit plug by first removing the

socket set screw using one of provided Allen

keys shown in Image 16.

3. Attach Junction Box Adapter to the wall using

drywall screws or any optional hardware

suitable for the mounting surface.

4. Attach MegaDome® Wall Mount to Junction

Box Adapter as shown in Image 17.

5. Connect ¾” NPT Conduit to Junction Box

Adapter

6. Run Ethernet Cable and outside power cable (if

necessary) through the Junction Box Adapter

and Wall Mount.

7. For installation of the camera, please

reference “Mounting the Camera”.

Arecont Vision MegaDome®Installation Manual

9 | Page

MegaDome®2 Junction Box Adapter (SV-JBA) for MD-WMT2 Installation Instruction

SV-JBA only fits with MD-WMT2 but not with

MegaDome®2 and MD-CMT!

Caution:

A. Junction Box Adapter

Inside the box:

B. Pack of four (4) machine screws

C. One double sided hex key

D. Pack of four (4) wood screws and four (4)

dry wall anchors

E. Large round rubber gasket

•#2 Phillips head screw driver

Not included but needed:

•D4SO Wall Mount, MD-WMT

•¾” NPT Conduit (if necessary)

Image 18

1. Remove Junction Box and hardware from the

box

Image 19

2. Remove the conduit plug by first removing the

socket set screw using one of provided Allen

keys.

3. Attach Junction Box Adapter to the wall using

drywall screws or any optional hardware

suitable for the mounting surface.

4. Attach D4SO Wall Mount to Junction Box

Adapter as shown in Image 19.

5. Connect ¾” NPT Conduit to Junction Box

Adapter.

6. Run Ethernet Cable and outside power cable (if

necessary) through the Junction Box Adapter

and Wall Mount.

7. For installation of the camera, please

reference “Mounting the Camera”.

Altri manuali per MegaDome 2

Altri manuali Arecont Vision Telecamera di sicurezza

Arecont Vision

Arecont Vision SurroundVideo Series Manuale utente

Arecont Vision

Arecont Vision Contera AV02CID-100 Manuale utente

Arecont Vision

Arecont Vision AV1215PM-S Manuale utente

Arecont Vision

Arecont Vision MegaDome AV1355DN-1HK Manuale utente

Arecont Vision

Arecont Vision D4S Series Manuale utente

Arecont Vision

Arecont Vision D4SO Series Manuale utente

Arecont Vision

Arecont Vision D4SO Series Manuale utente

Arecont Vision

Arecont Vision SurroundVideo Omni AV12176DN-08 Manuale utente

Arecont Vision

Arecont Vision Contera Micro Bullet Manuale utente

Arecont Vision

Arecont Vision MicroDome AV1455DN-S Manuale utente

Arecont Vision

Arecont Vision AV12ZMV-301 Manuale utente

Arecont Vision

Arecont Vision MegaBall AV2245PM-W Manuale utente

Arecont Vision

Arecont Vision AV2100 Manuale utente

Arecont Vision

Arecont Vision ConteraIP Fisheye AV12CPD-236 Manuale utente

Arecont Vision

Arecont Vision SurroundVideo Omni AV12176DN-NL Manuale utente

Arecont Vision

Arecont Vision MicroDome AV2455DN-S Manuale utente

Arecont Vision

Arecont Vision Contera AV02CLB-100 Manuale utente

Arecont Vision

Arecont Vision AV08ZMV-300 Manuale utente

Arecont Vision

Arecont Vision AV2225PMIR Manuale utente

Arecont Vision

Arecont Vision MegaBall AV2245PM-W Manuale utente

Arecont Vision

Arecont Vision MicroDome Manuale utente

Arecont Vision

Arecont Vision AV12975DN-NL Manuale utente

Arecont Vision

Arecont Vision AV2325DNIR Manuale utente

Arecont Vision

Arecont Vision MegaView 2 AV1225PMIR-S Manuale utente

Manuali Telecamera di sicurezza popolari di altre marche

Okina USA

Okina USA SIR36-870VF650LP Manuale utente

Divio

Divio NDR155PA Manuale utente

Canon

Canon VB-C500D Manuale utente

Easy Access

Easy Access EasyGuard Manuale utente

Vivotek

Vivotek FD9389-EHV-v2 Manuale utente

TUYA

TUYA COSMO W2 Manuale utente

Eusso

Eusso UNC7500-IR Guida all'installazione

urmet domus

urmet domus 1096/204 Manuale utente

VC VC20 series Manuale utente

Axis

Axis Q1614 Manuale utente

ieGeek

ieGeek DD201 Manuale utente

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuale utente

Vicon

Vicon V662-D-1 Istruzioni operative

Grundig

Grundig GCH-K0274P Manuale utente

Lorex

Lorex VANTAGE LBC7032 Manuale utente

4xem

4xem WPT Manuale utente

Samsung

Samsung SCV-3082 Manuale utente

Vitek

Vitek VTC-C544 Manuale utente