Argox A-50 Manuale utente
1
1. Checking Your Box
Receiving the box of your printer, you are advised to
check first for the possible shipping damage. There are two ways
you can do it:
1. Inspect the outer appearances of both the box and the printer
for possible damage.
2. Raise the top cover of the printer to see if the media
compartments are in order.
If damages did occur, immediately file the claim to the shipping
company for settlement.
Having performed the primary inspections,next
step, please check whether you have received the following
accessories together with the printer. If there is any item missing,
contact your local dealer to get it.
2
* Not available for A-50
Power Adapter
* Sample Media
* Ribbon
CD Rom Disk
User’s Manual
Printer
3
2. Power Supply
WARNING:
NEVER OPERATE THE PRINTER AND POWER SUPPLY IN
AN AREA WHERE THEY CAN GET WET.
1. The Power Adapter has a barrel connector on one end that
must be inserted into the power jack on the back of the printer.
2. Plug the other end of the cord into an appropriate AC electrical
outlet.
3. When plugging the connector into power jack, please leave the
power switch at "O" position and don't touch the 36 pin parallel
connector.
Power Switch
Barrel Connector
Power Jack
Power Adapter
AC Electrical Outlet
36 Pin parallel connector
4
3. Parts and Features
Top Cover
Power Switch
Power Indicator
Ready Indicator
Feed Button
5
* Not available for A-50
* Ribbon Pick-up Holder
Release Levers
Media Hanger
* Ribbon Supply Holder
Thermal Printhead
6
4. Loading the Ribbon
Note:
This section is not applicable to the direct thermal printing.
1. Lift the top cover to expose the media compartment.
7
Ribbon Supply Holder
2. Unlatch the print head module by pushing the two white release
levers on the sides toward the rear.
3. Turn over the print head module to expose the ribbon supply
holder.
Media Compartment
Release Lever
Print Head Module
8
4. Unwrap the ribbon roll pack and separate the ribbon roll and
the bare core.
5. Attach the edge of the ribbon on the bare core and wind it a
little bit onto the core.
6. Insert the ribbon roll into the supply holder. (First snap in the left
side and then the right side.)
Ribbon Roll
Bare Core
9
7. Turn back the print head module and then insert the bare core
into the pick-up holder. (First snap in the left side, then the right
side.)
10
8. Turn the wheel of the print head module to ensure the ribbon is
tightly wound.
9. Press down the print head module on both sides firmly till you
hear a snap.
Wheel
Print Head Module
11
5. Loading the Media
A Series printers can be operated in three different options:
standard, peel-off, or with a cutter.
- Standard mode allows you to collect each label freely.
- In peel-off mode, the backing material is being peeled away from
the label as it is printed. After the former label is removed, the
next one will be printed.
- In cutter mode, the printer automatically cuts the label after it is
printed.
Standard Mode
1. Lift the top cover to expose the media compartment.
12
2. Remove the media hanger.
3. Load the media roll onto the hanger.
4. Unlatch the print head module.
5. Left the peeler cover easy for label easy into the slot.
Media Compartment
Media Hanger
Ribbon Roll
(Not Available
for A-50)
Peeler Cover
13
6. Lead the label through the media guides with the other hand.
The media guide can be adjusted centrality to well fit with
different label width.
Media Guides
14
7. Press down the print head module firmly on both sides till you
hear a snap.
Print Head Module
15
8. Close the top cover and turn on the printer or press the feed
button if the printer is already on.
Feed Button
16
Peel Off Mode
1. Loose two attached screws on the back of peeler cover.
2. Remove the peeler cover.
Screw
17
3. Plug in the dispenser connecter.
4. Mount the dispenser module.
Dispenser Connecter
Dispenser Module
18
5. Secure two attached screws on the back of peeler cover.
6. Lead the label through the media guides and dispenser.
Media Guides
Dispenser
Screw
19
7. Press down the print head module firmly till you hear a snap.
8. Close the top cover and turn on the printer or press the feed
button if the printer is already on.
Feed Button
20
9. Press the feed button and the label backing paper will come out
from the slot under dispenser.
Note :
The feed button will not drive the printer to peel. The
peeling function can be executed only when the software
setting is ready.
Label
Backing Paper
Feed Button
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Argox Stampante
Argox
Argox R-400plus Manuale utente
Argox
Argox O4 Series Manuale utente
Argox
Argox P4 Series Manuale utente
Argox
Argox OS-214ZIP Manuale utente
Argox
Argox O4 Series Manuale utente
Argox
Argox X2000 Manuale utente
Argox
Argox iX4 Series Manuale utente
Argox
Argox O4 Series Manuale utente
Argox
Argox CP Series Manuale utente
Argox
Argox AME-2230B Manuale utente
Argox
Argox OS Series Manuale utente
Argox
Argox AME-3230 Manuale utente
Argox
Argox OS Series Manuale utente
Argox
Argox iX4 Series Manuale utente
Argox
Argox Smart CP-2140 Manuale utente
Argox
Argox Xellent X-1000VL Manuale utente
Argox
Argox MP Series Manuale utente
Argox
Argox AME-3230 Manuale utente
Argox
Argox O4 Series Manuale utente
Argox
Argox PI-10X0 Manuale del proprietario
