ARTHUR HOLM Dynamic 3 Manuale utente

Assembling guide Dynamic 3 + DTalk

Information

Dynamic 3 monitor is available in a special version prepared to be

assembled with DynamicTalk device. This special version is supplied

with all accessories to be assembled.

DynamicTalk can be assembled at the right side, at left side or at both

sides. This guide shows how to assemble it at left side (the assembling

at the right side follows the same process).

INTRODUCTION

Manipulation of the product should be avoided, no stress should be applied to the product except from

the instructions given in this document. Cutting, drilling, soldering, adding of electrical and mechanical

components can cause danger and should be avoided by all mean. Not complying with these direction

will result in a lost of the Arthur Holm warranty. Albiral Display Solution S.L. shall not be held liable for

any loss or injury incurred as a result of modifications made to goods by anyone other than the supplier

or the supplier's authorised representative without the supplier's written permission. Such

modifications shall be deemed to terminate any further guarantee obligations. Compensation will not be

paid for wages, loss of profit, waste of time, packing and transport or any financial liability resulting

from defects in the goods. (Albiral Display Solutions shall not be liable for any loss or injury caused by

negligence.)

PATTERN HOLE

Pattern hole dimensions for milling are specified in the general dimensions for each reference.

ATTENTION

Preparing the assemble

(x2) DIN 9021 4,3

•Being D3 mounted on the table: Mount the (x2)

washers and the (x2) wing nuts supplied at the bolts

shown. Screw the wing nuts until they are flushed with

the end of the bolt.

(x2) DIN 315 M4

Flush bolt

View from below

the table

View from below

the table

Assembling DynamicTalk 4

•Insert DynamicTalk in the indicated position.

The top plate must be just above the washers

•Turn DynamicTalk until the two open holes

on the top plate are in contact with the bolts

Assembling DynamicTalk

•Push carefully the DynamicTalk upward, please

take care with the hatch of the cover plate.

•There is a guide bolt that has to enter into the

hole of the top plate

•Keeping pressed up the DynamicTalk, screw

the wing nuts with the finger.

Assembling DynamicTalk

•Enter the mounting plate through the DynamicTalk.

•If Dynamic talk has a cable to connect the

microphone: pass the Microphone cable + connector

trough the mounting plate hole.

Assembling DynamicTalk (STANDARD & BOSCH)

•Fix the DynamicTalk to the mounting plate

(x2) DIN 6798 5,3

(x2) DIN 7985 M5x12

Follow This step for standard DynamicTalk or

DynamicTalk with BOSCH

•Fix the mounting plate with washers and screws provided.

(x4) DIN 6798 5,3

(x4) DIN 7985 M5x10

Assembling DynamicTalk (DIS)

•Fix the DynamicTalk to the mounting plate

(x2) DIN 6798 5,3

(x2) DIN 7985 M5x12

Follow This step for DynamicTalk with DIS

or TELEVIC microphone.

•Fix the mounting plate with washers and screws provided.

(x4) DIN 6798 5,3

(x4) DIN 7985 M5x10

Connect XLR connector from the DynamicTalk

to the socket (Microphone IN)

www.arthurholm.com

Questo manuale è adatto per i seguenti modelli

Altri manuali ARTHUR HOLM Monitor

ARTHUR HOLM

ARTHUR HOLM AH 18D3 RHDGA RV Manuale utente

ARTHUR HOLM

ARTHUR HOLM D1Twin Manuale utente

ARTHUR HOLM

ARTHUR HOLM Dynamic DB2 Manuale di istruzioni per l'installazione

ARTHUR HOLM

ARTHUR HOLM AH24DB2 Manuale utente

ARTHUR HOLM

ARTHUR HOLM AH10DB2 Manuale utente

ARTHUR HOLM

ARTHUR HOLM AH1 Series Manuale utente

ARTHUR HOLM

ARTHUR HOLM DynamicX2Talk Manuale utente

ARTHUR HOLM

ARTHUR HOLM DynamicX2 AH22DX216GA Manuale utente

ARTHUR HOLM

ARTHUR HOLM AH12D1HGA Manuale utente

ARTHUR HOLM

ARTHUR HOLM AH17 NTTHD Manuale utente

ARTHUR HOLM

ARTHUR HOLM RISE AH12RI Wide Manuale utente

ARTHUR HOLM

ARTHUR HOLM AH1 Series Manuale utente

ARTHUR HOLM

ARTHUR HOLM Dynamic2 AH12D216A Manuale utente

ARTHUR HOLM

ARTHUR HOLM DB2Share Manuale utente

ARTHUR HOLM

ARTHUR HOLM DynamicX2KM Manuale utente

ARTHUR HOLM

ARTHUR HOLM DynamicX2KM Manuale utente

ARTHUR HOLM

ARTHUR HOLM RISE AH12RI Wide Manuale utente

ARTHUR HOLM

ARTHUR HOLM AH22DRM Manuale utente

ARTHUR HOLM

ARTHUR HOLM DynamicX2 AH22DX216DGA Manuale utente

ARTHUR HOLM

ARTHUR HOLM AH17S HDGA Manuale utente

ARTHUR HOLM

ARTHUR HOLM DB2 Series Manuale utente

ARTHUR HOLM

ARTHUR HOLM Dynamic3Talk Manuale utente

ARTHUR HOLM

ARTHUR HOLM AH24DB2 Manuale utente

ARTHUR HOLM

ARTHUR HOLM Dynamic3Reverse Manuale utente

Manuali Monitor popolari di altre marche

Linear Acoustic

Linear Acoustic LQ-1000 Manuale utente

AOC

AOC I2579V Manuale utente

Gateway

Gateway FPD1520 Manuale utente

Furuno

Furuno Mu 120c Manuale utente

Asus

Asus VB171D - 17" LCD Monitor Manuale utente

Dell

Dell S2230MX Istruzioni utente

Philips

Philips 107C64 Manuale utente

Dell

Dell S2409WFP Manuale utente

EverFocus

EverFocus EN-7517E Manuale utente

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuale utente

Dell

Dell Precision 7680 Manuale di istruzioni

LG 50PM1M - - 50" Plasma Panel Manuale utente

Bosch

Bosch DDU 9 Manuale utente

Acer

Acer A231HL Manuale utente

Philips

Philips 86BDL4152T Manuale utente

NEC

NEC AccuSync LCD5V Manuale utente

Emay

Emay SleepO2 Manuale utente

IBM

IBM 6360 Istruzioni per l'installazione