ASCOM 914T - 1 Manuale utente
QUICK REFERENCE GUIDE
ascom
Ascom 914T
PockeT receiver
]
]
GB SE DE NO DK FR FI NL ES PT IT
ascom
M2377630 Ver. B, Sep 2008 – Ascom Wireless Solutions, Sweden – Specifications are subject to change without notice
www.ascom.com ]
]
NO
DK
FR
FI
NL
ES
PT
IT
DE
SE
GB
English ................................... 2
Svenska ................................. 8
Deutsch................................ 14
Norsk.................................... 22
Dansk................................... 28
Français ............................... 34
Suomi................................... 40
Nederlands........................... 46
Español................................ 52
Português............................. 58
Italiano.................................. 64
2
The LED indicates:
•When turning on the receiver
•When receiving a paging or an alarm
English
Display Icons
Charge or replace the battery
New message (the symbol flashes)
Message longer than 2 × 12 characters
Audible signal switched off
Out of range/Error indication
Info message
Time stamp (the time when the message was
received)
LED
Display
IR receiver
mocsa
Function button
GB
3
Ascom 914T is a robust pocket text receiver used in system 900.
The receiver has a two-line display and shows 2 x 12 characters
at the same time. It can receive messages of up to 120 characters
in each message. The receiver has a memory for 10 messages
with altogether 480 characters. Six call numbers can be
programmed and five of them can be enabled/disabled. The
pocket receiver is designed for use in tough environments and
where there is a need for long text presentations.
Note: Your receiver can have functions other than described
here, depending on the pre-programmed parameters.
Turning the receiver ON
One short press on the Function button. The identity is shown in
the display.
Turning the receiver OFF
Two long presses on the Function button.
Scrolling through messages
One short press on the Function button.
Erasing messages
One long press on the Function button until ******** appears.
Accepting a message
One short press on the Function button, stops flashing.
Product presentation
Functions
Characters per message 120
Messages stored 10
Characters in memory 480
Group paging numbers 5
Absence indication Yes
Time stamp Yes
Time display Yes
Out of range indication Yes
Vibrator option
Basic functions
4
Replacing the battery
1. Turn off the receiver.
2. Unscrew the screw with a coin and remove the cover.
3. Replace the battery and close the cover. It will take up to 10
seconds before the receiver starts up.
Long messages
The Ascom 914T can receive long messages with a maximum of
10 lines. A message with more than two lines is marked with
The message scrolls automatically, but when it stops, it can be
started again by a short press on the Function button.
When the identity is shown in the display, one long press on the
Function button will access the function settings. A short press
on the button scrolls between function settings and a long press
confirms the choice.
Main menu
Long press Off?
Short press Tone?
Short press Menu? long press Sub-menu
VOL
Call No.
Extra paging Nos
RTC
Remind
LCD
Program?
Short press Exit?
One long press confirms the choice.
Sub-menu functions
• Changes the beep signal volume
• Shows the call number
• Enables/disables the 5 extra paging numbers
• Shows time stamp (RTC)
• Reminder beep for unacknowledged pagings
Function settings
GB
5
• Rotates the display 180° (LCD)
• Programmable via radio
• Exit to identity mode
One long press enables/disables.
Pagings, originally intended for someone else, can be received by
your Ascom 914T by either five extra paging numbers, or when
the call has been automatically diverted to your receiver. The
original number is shown at the end of the message.
means that the call was received by one of the five extra
paging numbers.
means that the call has been diverted to your pager.
When the receiver is placed in a storage/charging rack with
absence indication, anyone paging the receiver automatically
receives indication of absence. The person sending the paging is
thus informed that you cannot be reached at present.
By using the screensaver, a longer battery life is ensured. The
screensaver function is pre-programmed and shuts the display off
after a pre-set time. To activate the display again, press the
button. An incoming message turns the screensaver off
automatically. After reading the message, it is important to press
the button to return to ID mode. By this, the screensaver
function is reactivated.
When the symbol is displayed, you are probably outside the
coverage area. The symbol disappears when the receiver is within
the coverage area again.
The symbol is also shown if the internal error monitoring
function identifies an error.
Note that your Ascom 914T may not have all these functions and
features depending on parameter settings.
Call diversion
Absence indication
Screensaver
Out of range/Error indication
6
The power source is one single cell. The single cell may be
alkaline (AAA) or rechargeable NiMH. Use any LR3-sized battery
or the rechargeable Inductive Battery Pack IBP1B.
While the receiver is not in use, place it in the T967 Storage/
Charging Rack, to save battery.
If you are using a rechargeable battery, make sure to regularly
place the receiver in a charging rack, for example every night.
Charging Battery
The rechargeable Inductive Battery Pack IBP1B can only be
charged in the T967 Storage/Charging Rack. Standard secondary
cells and primary cells cannot be recharged inside the eqipment.
We recommend that the receiver must be charged in a dry
environment with a temperature range of 0 to +40°C.
This equipment is intended to be used in the whole EU & EFTA.
This equipment is in compliance with the essential requirements
and other relevant provisions of R&TTE Directive 1999/51/EC.
The Declaration of Conformity may be consulted at:
https://www.ascom-ws.com/doc/
This equipment uses frequencies referring to different rules in the
various EU&EFTA countries.
A radio communication licence is in most cases neccessary for
the use of the equipment.
The frequencies required for operation of the radio equipment
must be notified and assigned prior to usage of the equipment.
Battery
Regulatory compliance statements
EU/EFTA only
GB
7
FCC compliance statements
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the transmitting antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the transmitter is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
Information to user
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Modifications
Any modifications made to this device that is not approved by
the supplier may void the authority granted to the user by FCC to
operate the equipment.
Regulatory compliance statements
USA and Canada only
8
Lysdioden indikerar:
• När mottagaren sätts på
• När en personsökning eller ett larm tas emot
Svenska
Displaysymboler
Ladda eller byt ut batteriet
Nytt meddelande (symbolen blinkar)
Meddelande längre än 2 x 12 tecken
Ljudsignal avstängd
Utanför räckvidd/felindikation
Infomeddelande
Tidsmärkning (klockslaget när meddelandet togs
emot)
Lysdiod
Display
IR-mottagare
mocsa
Funktionsknapp
Altri manuali per 914T - 1
2
Indice
Lingue:
Altri manuali ASCOM Ricevitore
