Associated Electrics RB10 Manuale utente
AssociatedElectrics.com
2
:: Introduction
:: KIT Features
:: Additional
Thank you for purchasing this Team Associated product. This assembly manual contains instructions and tips for building and
maintaining your new RTR. Please take a moment to read through this manual to help familiarize yourself with these steps.
We are continually changing and improving our designs; therefore, actual parts may appear slightly different than in the
illustrations. New parts will be noted on supplementary sheets.
Tools included:
• Allen wrenches 1.5mm, 2.0mm
:: Other Helpful Items
•2.4GHz 2-channel radio with new DVC (Dynamic Vehicle Control) receiver featuring built-in adjustable gyro
•High-torque, metal-gear Reedy servo with spring style servo saver
•Powerful Reedy 3300kV brushless motor
•Water-resistant high-power Reedy brushless speed control with T-plug connector and LiPo low voltage cutoff
•Water-resistant enclosed receiver box
•Factory-finished Off-road Buggy body and wing
•Off-road buggy race car-inspired dish wheels
•High-grip off-road tires with aggressive tread pattern
•Aluminum 12mm big bore coil-over shock absorbers
•Durable and lightweight aluminum top shaft
•Low center-of-gravity molded composite chassis with hook-and-loop battery straps that accommodate both NiMH and
2S and 3S LiPo battery packs
•Rear CVA drive shafts for more durability
•2.6:1 ratio gearbox with heavy-duty sealed gear differential and extremely adjustable slipper clutch
•Rugged steel turnbuckles for adjustable camber and front toe-in
•Adjustable suspension geometry
•Vertical ball ends for roll center adjustments, front and rear
•Many Factory Team options already available!
•Metric hardware throughout
•22 precision rubber-sealed ball bearings
Your new RTR comes factory assembled including radio gear, motor, and
ESC. However, there are some items you will need to complete your kit
(refer to catalog section for suggestions):
• AA-size batteries for transmitter (#302)
• Peak Detection Charger or LiPo Compatible Charger
• 6 cell NiMH battery pack or 2/3S LiPo battery pack w/High Current T Plug.
• Green Slime shock lube (AE #1105) • Cyanoacrylate glue (AE #1597)
• Thread Locking Compound (AE #1596) • Silicone Shock Fluid (Refer to catalog for complete listings)
• Silicone Diff Fluid (Refer to catalog for complete listings) • Body Scissors (AE #1737)
• FT Hex Wrenches (AE #1650) • FT Nut Drivers (AE #1663 - 1668)
• Hobby Knife • Wire Cutters • Soldering Iron
• Calipers or a Precision Ruler • Reamer / Hole Punch (AE #1499) • Ride Height Gauge
• Turnbuckle Wrench (AE #1114) • Needle Nose Pliers
Associated Electrics, Inc.
21062 Bake Parkway.
Lake Forest, CA 92630
http://www.RC10.com · http://twitter.com/Team_Associated · http://www.instagram.com/teamassociatedrc/ · http://www.facebook.com/TeamAssociated/
Customer Service
Tel: 949.544.7500
Fax: 949.544.7501
AssociatedElectrics.com
3
:: Hardware - 1:1 Scale View
3x8mm (25201)
3x10mm (25202)
3x12mm (25203)
3x14mm (89208)
3x16mm (25204)
Flat Head (fhcs)
2x3mm (31509)
2x4mm (31510)
Aluminum (8545)
2.5x8mm (31521)
2.5x10mm (31522)
3x5mm (31530)
3x8mm (31532)
3x10mm (25211)
3x12mm (89202)
3x14mm (25187)
3x16mm (89203)
3x22mm (25189)
3x24mm (89204)
3x26mm (89205)
3x30mm (91478)
Button Head (bhcs) Ball Bearings
3x7x3mm (91475)
5x10x4mm (25237)
6x13x5 (91562)
10x15x4 (91563)
3x3mm (25225)
Set Screws
Notes:
E-clip 1/8 (6299)
Clips
Ballstuds
HD 6mm (91047)
Titanium HD 6mm (91751)
HD 8mm (91048)
Titanium HD 8mm (91752)
HD 10mm (91049)
Titanium HD 10mm (91753)
M2.5 Locknut, Shock Piston
(89215)
M3 Nut (91477)
M3 Alum. Locknut, Blue (31550)
M3 Locknut, Black (25215)
M3 Locknut w/Flange (25612)
FT 3mm Locknuts, Blue(25392)
M4 Serrated w/Flange (91738)
FT M4 Locknuts w/Flange,
Blue (31551)
M4 LP Serrated Nut (92254)
Nuts (lock/plain)
Servo Mount Washer (7337)
(.250 x .125 x .815)
FT Ballstud Washer, Aluminum
(0.5mm) (31381)
FT Ballstud Washer, Aluminum
(1mm) (31382)
FT Ballstud Washer, Aluminum
(2mm) (31383)
Shims and Washers
Cap Head (shcs)
2.5x14mm (71032)
3x24mm (89225)
3x45mm (89279)
:: Table of Contents
:: Notes
1................... Cover
2................... Introduction
3...................1:1 Hardware “Fold Out”
4................... Table of Contents
5 - 7..............Quick Start Guide
8....................Front Top Plate and
Steering Build
9 - 10...........Front Suspension Build
10 - 11.........Rear Suspension Build
11 - 12........Gear Differential Build
12 - 13........Gearbox Build
13.................Slipper Build
13 - 14........Gearbox Install
14.................Rear Hub and CVA Build
15.................Turnbuckles Build
16 - 17.........Shocks Build
17 - 19........Electronics Build
19 - 20........Tires and Body Build
20 - 21....... Tuning Tips
22 - 29........Catalog
30................Back Cover
4
There is a 1:1 hardware foldout page in the
front of the manual. To check the size of a part,
line up your hardare with the correct drawing
until you find the exact size. Each part in the
foldout has a number assigned to it for ordering
replacement parts.
This symbol indicates a special
note or instruction in the manual.
This symbol indicates a Racers Tip.
!
Associated Electrics, Inc.
21062 Bake Parkway.
Lake Forest, CA 92630
http://www.RC10.com · http://twitter.com/Team_Associated · http://www.instagram.com/teamassociatedrc/ · http://www.facebook.com/TeamAssociated/
Customer Service
Tel: 949.544.7500
Fax: 949.544.7501
5
4/21
:: Quick Start Guide
:: Quick Start Guide - (cont.)
:: Quick Start Guide - (cont.)
Battery Charging Steps and Safety:
Remove the battery from the vehicle before charging.
Place battery on a fire resistant surface.
Avoid any contact with water or other liquids.
Be sure to select the correct charging mode for the type
of battery you are charging.
ALWAYS use a compatible charger for charging your batteries.
Caution: Never leave the battery unattended while charging.
Always disconnect the charger from the power source when
finished charging.
Caution: Always disconnect the battery when you are
finished driving the vehicle.
Battery Installation:
1. Install the battery with the battery wires directed
towards the front of the vehicle.
2. Secure the hook and loop strap near the rear shock
tower. Pull the strap over the motor wires for added
security.
3. Secure the hook and loop strap near the front shock
t o w e r.
You may move the foam pad to either the front or the
rear of the battery compartment to adjust the weight
balance of the vehicle.
Peak Detection
Quick Charger
1
2 3
6
:: Quick Start Guide - (cont.)
:: Quick Start Guide - (cont.)
Battery Notes and Tip:
Connect the battery as shown.
Disconnect the battery when not in use!
LiPo: LiPo batteries (lithium polymer) are high current
rechargeable batteries. LiPo batteries offer extended run time
and peak performance over NiMH batteries. They require a
peak detection charger designed specifically for LiPo batteries.
These batteries require special care and handling.
LiPo batteries are recommended for advanced users only!
ALWAYS charge a LiPo battery in LiPo mode with balance lead
connected to charger! Go to http://bit.ly/lipowarnings for more
info.
If using a 3S LiPo battery, use a smaller pinion gear as a starting
point (use part #1335 17T Pinion). This provides the correct
gear ratio required for the more powerful 3S LiPo battery.
Gearing will depend on the surface you are running on, and the
size of the track/area that you are driving in.
Radio System Tuning and Controls:
RULE: Transmitter on First/Vehicle on Second,
Vehicle off First/ Transmitter off Last!
1) Slide the battery cover to remove cover.
2) Install alkaline or rechargeable AA size
batteries into the battery holder.
3) Slide the battery cover back into place making
sure it is completely closed and secure.
4) Turn the power ON. If the power indicator LED
fails to light, check the batteries for insufficient
contact or incorrect polarity.
On/Off Switch
7
:: Quick Start Guide - (cont.)
Radio System Tuning and Controls:
DO NOT hold the trigger when turning on the radio.
If using optional battery for transmitter, be sure to plug
it in correctly. Plugging in a battery backwards can
cause damage.
Refer to Radio owners manual for more in-depth
instructions on radio operation and functions.
:: Quick Start Guide - (cont.)
Adjust steering
trim so front
wheels point
straight.
Neutral
Push trigger
for Brake
Pull trigger
for Throttle
Install body and body clips.
Ready to go!
Install antenna wire
through antenna tube,
then install antenna
tube as shown.
8
:: Front Top Plate and Steering Build - Step 2
:: Front Top Plate and Steering Build - Step 3
:: Front Top Plate and Steering Build - Step 1
Do not overtighten steering bolts. Make sure
there is free movement in the steering rack.
!
Note orientation
of steering rack.
!
Note orientation
of the brace.
!
91475
3 x 7 x 3
Ball Bearing
91391
Steering
Rack
x4
x2
x2
91047
Heavy-duty
Ballstud,
6mm
91391
Steering
Rack Crush
Tube
91391
Steering
Bellcrank
Brace
x2
89202
M3 x 12mm
BHCS
91047
Heavy-duty
Ballstud,
6mm
91391
Steering
Bellcrank
Brace
91475
3 x 7 x 3
Ball Bearing
x4
x2
25189
M3 x 22mm
BHCS
91358
Chassis
Brace Set
(Top Plate)
x2
25202
M3 x 10mm
FHCS
91359
Bulkhead
71092
SR10
Chassis
9
:: Front Suspension Build - Step 1
:: Front Suspension Build - Step 3
:: Front Suspension Build - Step 2
Build 2 (1 left, 1 right)
Build 2 (1 left, 1 right)
91048
Heavy-duty
Ballstud,
8mm
91417
Caster
Block
x2
31530
M3 x 5mm
BHCS
25215
M3 Locknut,
black
25237
5 x 10 x 4
Bearing
71188
SR10 Front
Axle,
4.5mm
91417
Steering
Block
#1596
thread lock
91047
Heavy-duty
Ballstud,
6mm
x2
89202
M3 x 12mm
BHCS
91402
Caster
Block
Bushing
x2
x2
x2
31510
M2 x 4mm
BHCS
31509
M2 x 3mm
BHCS
91394
Hinge Pin
(front, outer)
71068
Front Arms
91394
Hinge Pin
(front, Inner)
71049
Front Hinge
Pin Brace
25211
M3 x 10mm
BHCS
x2
#1596
thread lock
71093
SR10 Front
Shock
Tower
91049
Heavy-duty
Ballstud, 10mm
x2
x2
31383
FT Ballstud
Washer,
Aluminum
(2mm)
91477
M3 Nut
(Black)
x2
x2
89205
M3 x 26mm
BHCS
(Threadlock
Not Included!)
(Threadlock
Not Included!)
!
!
10
:: Front Suspension Build - Step 4
:: Rear Suspension Build - Step 2
:: Rear Suspension Build - Step 1
91359
C Mount
91359
Rear Chassis
Plate
31521
M2.5 x 8mm
BHCS
71068
Rear Arms
x2
91394
Hinge Pin
(rear, Inner)
25187
M3 x 14mm
BHCS
91359
D Mount
x2
89208
M3 x 14mm
FHCS
25203
M3 x 12mm
FHCS
x2
x2
25211
M3 x 10mm
BHCS 91358
Rear Chassis
Brace
x2
31383
FT Ballstud
Washer,
Aluminum
(2mm)
91049
Heavy-duty
Ballstud, 10mm
x2
x2
89202
M3 x 12mm
BHCS
x4
x289208
M3 x 14mm
FHCS
72022
RB10
Bumper
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Associated Electrics Giocattolo
Associated Electrics
Associated Electrics 80930 Manuale utente
Associated Electrics
Associated Electrics RC8T Factory Team Manuale utente
Associated Electrics
Associated Electrics RC10TC6.2 Manuale utente
Associated Electrics
Associated Electrics B4.1 Manuale utente
Associated Electrics
Associated Electrics RC12L3 4015 Manuale utente
Associated Electrics
Associated Electrics RC82 Manuale utente
Associated Electrics
Associated Electrics RC18T Manuale utente
Associated Electrics
Associated Electrics 7058 Manuale utente
Associated Electrics
Associated Electrics RC10 Worlds Car Kit Manuale utente
Associated Electrics
Associated Electrics RC12LC Manuale utente
