Astell SWIFTLOCK Manuale utente

Powerscroft Rd

Sidcup

Kent

DA14 5DT

United Kingdom

Tel 0208 300 4311

Fax 0208 300 2247

SWIFTLOCK

Multi-Purpose

Cylindrical Sterilizer

Electrically

Heated

INSTALLATION

INSTRUCTIONS

OPERATING

INSTRUCTIONS

MAINTENANCE

INSTRUCTIONS

SERVICE MANUAL

Complete Program Entry and

Operating instructions for the

Programmable Control System of

this STERILIZER detailing Front-

panel operation , Display and

Keyboard are provided in a separate

Astell Manual ;-Part No. MXN487

Part No MXN488 iss01 ed a

PDF created with FinePrint pdfFactory Pro trial version http://www.fineprint.com

MXN488 iss01 ed A page 1

CONTENTS

INTRODUCTION

2 Introduction , Log Book ,Machine

Specification Document Issues

3. Climatic Conditions , Storage and use.

Battery Backup.

INSTALLATION

4. Water/Steam services, Drainage

Safety Valve ; Drain Valve ; Vent Valve

5. Steam Inlet ; Condensate return (Steam

Heated Models)

6 Electrical installation ; Power supply cable

7 Power Supply Electrically Heated Models

8 Fuse Ratings Electrically Heated Models

9 Heater/Power wiring, 380-440V 3-Phase,

Heater/Power wiring, 200-240V 3-Phase

OPERATION

10 Operation- general description

Setting Parameters-1-Program Models

11 OPERATION-SWIFTCLAVE

Electrically Heated Models

(Copy and post near to Sterilizer)

12 OPERATION-SWIFTCLAVE

Electrically Heated Models

(With Load Sensing Timing)

(Copy and post near to Sterilizer)

13 OPERATION - DETAILED REVIEW.

Lid/Door Interlocks, Heating ,

Freesteaming Timing , Sterilize Timing

Load Sensed Timing (Option) ;

14 Load Simulators/Cooling locks

. Cooling System and Cooling Locks

15. Selection of a Cooling Lock ; Thermal Lag

& the dummy load

16 Media Holdwarm

17 Water Quality.

Overflow Warning Pipe

18 Chamber Cleaning-

Chamber Cleaning-Steam Heated Models

LOADING and INTERLOCKS

19. Load Containers and Loading

20. Safety Door Interlocks

[UK HSE. Guidance Note PM73]

MAINTENANCE AND TECHNICAL

21. Periodic Maintenance

Safety Valve Testing

22 Thermocouple Access Ports

Load Sensing Probes

23. Fuses, Overtemperature Cutout

Technical notes

24. Certificate Of Examination -

25. Temperature/Pressure Corellation chart

26. List of Electrical Drawings available.

(drawings supplied on request .)

Consult ASTELL sevice Dept. for

mechanical drawings.

DRAWINGS

FSTERILIZERS ARE HAZARDOUS

IF MISUSED

Do not operate this machine if unsure of

operating procedures .

PDF created with FinePrint pdfFactory Pro trial version http://www.fineprint.com

MXN488 iss01 ed A page 2

INTRODUCTION

The SWIFTLOCK range are modern, functional general - purpose laboratory

STERILIZERS designed with ease of use in mind . They feature the proven

SWIFTLOCK CLOSURE PAT system to give easy and rapid opening of the chamber,

together with an easy-to use Single- or Multi-program control system, to facilitate a

variety of uses.

GENERAL OPERATION AND LOG-BOOK

Although the historical safety record of laboratory STERILIZERS is good, remember

at all times that they store considerable potential energy, and should be treated with

respect and care. If correctly used and cared for, your ASTELL STERILIZER will

provide long, reliable & safe service.

Pay proper attention to regular maintenance. Never force the locking mechanism, or

operate the machine with any leaks, or incorrectly operating parts.

Report any defects to your Engineering/Supervisor. If deterioration or defects are

noticed, record them in a log book and contact our Service Department .

Record also the results of annual and periodic inspections. Every 4 to 6 weeks is

recommended for periodic checks. Check the logbook before you start using the

machine, as someone else may have recorded a fault of which you are not aware.

MACHINE SPECIFICATION AND CONTROL OPTIONS

The Control System Display will show various items of information when the Mains

Power is turned on , for example...

"SWIFTCLAVE STERILIZER" denotes STERILIZER Type

"ELECTRICAL HEATING" or "STEAM HEATING" "SOFTWARE ISSUE No. xyz"

"PRINTER SELECTED"

"PROGRAM SELECTION BY SUPERVISOR ONLY"....etc.

Please keep a note of these displays ; You may be asked to quote these to assist

the Astell service dept. if requesting service dept. attention .

DOCUMENT ISSUES AND DETAILS

Date

& MR no

Issue Ed. FILENAME

Details of changes and revisions inc. software issues and

associated manuals

300700 0I A MXN488-1.doc

Der from mxn463 electric only #6,-10

PDF created with FinePrint pdfFactory Pro trial version http://www.fineprint.com

MXN488 iss01 ed A page 3

CLIMATIC CONDITIONS AND SPECIFICATIONS

Storage of this product in cold or damp conditions may lead to a Hazard or operating

faults if the equipment is put into service before it has dried out and achieved

equilibrium with the surroundings of the operating site.

Place in the area where it is intended to use the equipment.

Do not connect to a power supply.

Allow 48 Hrs to reach Humidity Equilibrium.

CLIMATIC CONDITIONS

OPERATING

Permitted Humidity not exceeding 75% mean non-condensing.

Permitted Temperature range 0-40 C

Do not site the equipment in an area where there are significant quantities

of dust. this will gather on the electronics and cause malfunction.

Do not site the equipment in an area where Spray or fumes from other

equipment may touch the cabinet or cooling vents.

Do not hose down or wash the equipment. The electronics system is not

protected against jets of water.

STORAGE

Permitted Temperature range -10 / +70 C

Humidity not specified but an equalising time is required- see above.

BATTERY BACKUP

Data retention - Main system EEprom . No Battery Required

Real-time Clock ( in Printer Option ) Nicad Rechargeable battery Soldered In.

(Maintains date/time operation when turned off. Not used to store data.)

PDF created with FinePrint pdfFactory Pro trial version http://www.fineprint.com

MXN488 iss01 ed A page 4

WATER & STEAM SERVICES &

DRAINAGE PIPEWORK CONNECTIONS.

• The TANK DRAIN outlet must be connected to a suitable Building Drain to carry away

waste water.

• The Safety Valve exhausts into the room.

• A supply of cold Mains water is required

• The Autofill tank Overflow / Warning Pipe must be correctly arranged.

• Electrically heated models are provided with a Chamber Cleaning Drain which may be

connected to the Building Drain .

• Steam heated models require a supply of steam .The Condensate Drain should be

connected to the building drain .

PIPEWORK CONNECTIONS. and installation details

TANK DRAIN OUTLET

This is a 35 mm plastic drainage outlet pipe projecting from the rear of the machine.

It must be plumbed into a building drain , and carries water with a temperature of up to 60C, but

normally ambient-40C. The outlet pipework should be free-draining and have a downward slope of a

min. of 1- in 50 and should not be reduced in diameter. If the length is to exceed 10 metres the whole

of the length of drain pipework should be increased in diameter by at least one size.

MAINS WATER INLET

This is a Plastic Coloured Hose with a 3/4 BSP Female Threaded tap connector similar to a Washing

Machine Inlet Hose. This should be connected to a Cold Water Mains Supply , Minimum 0.5 Bar ,

Maximum 6 Bar pressure. This supply Must be provided with a Shutoff Valve ( a Washing-Machine-

Isolator Valve is suitable ). The supply must provide for a Maximum Flow-rate of 10 litres/minute.

DRIP-TRAY DRAIN

There is no separate driptray drain this is incorporated with the Tank Outlet.

TANK OVERFLOW / WARNING PIPE

This is a White Polypropylene 20mm pipe which projects from the rear of the machine and will carry

overflow water if the Level in the Autofill tank is too high. It should be fed to an open Tundish or drain.;-

U.K. Water Research Council and the U.K. water byelaws require Warning pipe outlets to be visible to

the operator.

SAFETY VALVE

The Safety-Valve exhausts vertically downwards at the rear of the machine close to the floor. When it

operates a large volume of low-velocity steam will be produced .

It must not be connected to any other pipework or altered .

Please see other references in this manual to SAFETY-VALVE TESTING.

AIR INLET

This is a screwed inlet socket fitted inline with a 1-way valve. An optional bacteriological filter is

available which may be-fitted to allow clean air- into the chamber as it cools. Consult your Supplier for

details of suitable filters.

DRAIN VALVE - Electric Heated Models ONLY

The Drain valve permits the Chamber to be drained for cleaning purposes. This is at the rear of the

STERILIZER fitted with a lever action hand-valve. The valve is shut when the handle is at RIGHT-

ANGLES to the pipe. This should be arranged to allow the chamber to be drained regularly. It may be

plumbed into a drain or tundish.

KEEP CLOSED DURING USE & DO NOT OPEN WHEN HOT OR PRESSURIZED.

STEAM HEATED MODELS ONLY

PDF created with FinePrint pdfFactory Pro trial version http://www.fineprint.com

MXN488 iss01 ed A page 5

STEAM INLET..

STEAM SUPPLY

This is a 3/8" BSP Screwed Gun-Metal Union. The steam supply should be connected to the gunmetal

union. The STERILIZER may be factory-fitted internally with a pressure reducing valve, .Where fitted

supply pressure should be between 4 and 7 Bar If a Pressure reducing valve is NOT factory- fitted,

steam supply pressure must be reduced to 4 Bar, +0 /- 0.5 Bar with a suitable Pressure Reducing

Valve before reaching the STERILIZER. Please refer to the Rating plate at the rear of the machine for

It is important to fit a pressure gauge into this supply line, after the pressure reduction valve, which will

indicate actual steam pressure available to the machine . A condensate draining steam trap must be

fitted immediately upstream of the STERILIZER, to remove all condensate as Free Water will stop

Sterilizing action.

Steam Supply Problems;-A common fault with installations is that long pipe runs, poor layout or poor

steam quality fill the STERILIZER Chamber up with water. This will be avoided if attention is paid to

Condensate separation. Ensure that the steam supply flow is adequate to feed the machine when

operating - The steam pressure in the line will fall when the machine is HEATING UP .

SUPPLY CONDENSATE RETURN SYSTEM

The steam Supply line must be properly installed. If provision is not made to automatically drain off the

condensate that forms in the supply line the STERILIZER will draw in large quantities of water. this will

stop the Sterilising action, and may cause damage.

Warning ; On new steam systems or those that have cooled beware condensate build-up in lines

which may cause water hammer & damage valves and instruments.

Correct installation and Steam Trap arrangements will avoid this.

STEAM DRAIN OUTLET ( Chamber Condensate )

On Steam Heated Models the Chamber is fitted with an Automatic Chamber Drain. The outlet from

this is the small diameter COPPER pipe at the bottom rear of the machine. It should be connected to a

suitable building drain capable of carrying steam condensate ( at up to 134C ) Connection into the

boiler-house condensate return is not advisable due to the possible bacteriological contamination of

returned condensate if any of the load contaminates the inside of the machine.

This outlet should be connected via an air-break to prevent back-suction.

PDF created with FinePrint pdfFactory Pro trial version http://www.fineprint.com

MXN488 iss01 ed A page 6

POWER SUPPLY INLET CABLE

SWIFTCLAVE STERILIZERS are supplied as standard with a fitted Power Supply Cable. Steam heated

Machines have a CEE22 type Power Inlet cable and plug. Electrically heated machines are supplied with

a 5-core or 3-core ready-fitted mains supply cable provided with a standard -type Industrial High-Current

plug. The Cable is of the heavy-duty SY type, Double-Vinyl covered and protected by a woven metal

braid. (Models for 220V 3-phase supplies may have alternative arrangements.)

The STERILIZER has been tested in the configuration in which it is delivered from the factory. Details of

the Supply Voltage and the Current rating, etc are given on the Serial-Number / Rating Plate attached to

the machine.

Cable Alteration

Should it be necessary to alter the supply cable to suit local regulations or arrangements , the new power

supply cable should be arranged in flexible conduit or use similar suitably protected power cable rated to

carry the Maximum Current per Phase for 3-phase machines, and 5 Amps {Single Phase} for Steam

Heated machines. The connections are made to Terminals in the Power Input Box. The Cable should

pass under the lower edge of the rear panel, or through the cutout provided below the Power Input Box,

allowing the panel to be removed for access.

This machine must be wired with a protective earth.

RECORDER POWER FEED

The recorder options include an automatically controlled 240 Volts 1 Amp power outlet via a CEE22

Outlet connector. This is intended to power ONLY an Astell approved Recorder System. Instructions for

use are provided with the Recorder option. Some versions may use a different connector and the output

may also include remote control low-voltage signals.

Do Not Connect Any Other Equipment To This Outlet .

VOLTAGE RATING PLATE

Before attempting an installation, consult the SERIAL NUMBER / RATING PLATE fitted to the machine

which gives supply type and voltage requirements

PDF created with FinePrint pdfFactory Pro trial version http://www.fineprint.com

MXN488 iss01 ed A page 7

ELECTRICALLY HEATED MODELS

Consult the SERIAL-No./ VOLTAGE RATING PLATE Sited at the rear of the machine, or on some

models , near the front to one side. The STERILIZER is normally delivered with the supply arrangement

to suit the voltage and supply specified at the time of ordering. Should the Power Lead need to be

altered, Appendix 1, figures show how the 1 or 3-phase supply is connected to the terminals in the power

input box. Several models are available, With different Heaters and Supply wiring. Check the Power

Rating on the Rating Plate and refer to the details below:

[ PLEASE NOTE .. Voltages given are measured phase-to-phase. ]

SWITCHED FUSED SUPPLY ISOLATOR

The Power must be fed from an EXTERNAL SWITCHED FUSED ISOLATOR .This must be sited within

1 M of the machine. Astell STERILIZERs for 380-440 V 3-phase supplies may be supplied with a fitted

power lead nominally 2.5 M long ready-wired to a High-Current IEC power plug. The Site should be

provided with a Power Outlet socket to match the power connector. The following connector types are

fitted -

Supply Rating Fitted Plug on machine Outlet on wall

380-440V

3-Phase models

all heater ratings

CEE17 , EN60-309 , BS4343 415V

3P+N+E PLUG ip44 32 AMP

( RED)

CEE17 , EN60-309 , BS4343 400V

3P+N+E SOCKET ip44 32 AMP

(RED )

200-220V

3-Phase models

all heater ratings

*** Not normally Supplied ***

CEE17 , EN60-309 , BS4343 240V

3P+N+E PLUG ip44 63 AMP

( RED ),

*** Not Normally Supplied ***

CEE17 , EN60-309 , BS4343 240V

3P+N+E SOCKET ip44 63 AMP

( RED ) ,

Suggested Connector alternatives for installations.

Connector Description Lewden Electrical Argall Ave

London E10 7QD Part No

RS components PO. box

99 , Northants NN179RS

Part No

CEE17 , EN60, BS4343 240V

2P+E ip44

32 Amp ( BLUE )

Plug = PM32/501 or PM32/511

Socket = PM32/541,

Plug =847-304 or 490-

447

Socket = 187-1083

CEE17 , EN60-309, BS4343

415V 3P+N+E ip44

32 AMP ( RED ),

Plug = PM32/508 or PM32/518

Socket = PM32/548

Plug =827-386 or 490-481

Socket = 187-1128

CEE17 , EN60-309, BS4343

240V 3P+N+E PLUG ip44

63 AMP ( RED ),

Plug = PM63/501 or PM63/507

Socket = PM63/547

Not available

Where a mains cable is not supplied fitted please see the drawings at the rear of this manual.

Fitted Mains Lead Wire Colours

3-Phase STERILIZERs

Earth Phase1 Phase2 Phase3 Neutral

Green/Yellow Brown Black Black Blue

Single-Phase STERILIZERs

Earth Line/Live Neutral

Green/Yellow Brown Blue

PDF created with FinePrint pdfFactory Pro trial version http://www.fineprint.com

MXN488 iss01 ed A page 8

The Screening/Braid of the Armoured cable is earthed at the STERILIZER end. If the cable is

shortened, Cut the Plug end . Leave the STERILIZER end untouched or restore earthed Braid

connection.

Fuse or Contact-Breaker Trip Current Ratings-

The Supply ratings of the Electrically Heated models are given on the RATING PLATE at the rear of

the sterilizer. . If You are unsure please contact ASTELL or the supplying agent.

200-220V 3-Phase supplies ( with option AAN110 or AAN111)

Please note that the supply ratings for these models are approximately double the current ratings of

the 380/415 volt versions, typically 60A/Phase

Power Supply Connections/ Supply requirements

Consult the SERIAL-No./VOLTAGE RATING PLATE Sited at the rear of the machine, or on some

models , near the front to one side. The STERILIZER is normally delivered with the supply arrangement

to suit the voltage and supply specified at the time of ordering.

The Power Lead is part of the machine as certificated for compliance with the EMC directive. Inside the

Power Input Box are Suppressors and capacitors essential to the EMC performance of the control

system electronics.

Should the Power Lead need to be altered any changes must be carried out as detailed below and no

modifications or substitutions of parts made inside the STERILIZER Power Input Box. Appendix 1,

figures show how the supply is connected to the terminals in the power input box.

The Power must be fed from an EXTERNAL SWITCHED FUSED ISOLATOR .

This must be sited within 1 M of the machine.

PDF created with FinePrint pdfFactory Pro trial version http://www.fineprint.com

MXN488 iss01 ed A page 9

FOR 380/440 VOLT 3-PHASE SUPPLY

These use 220/230v x 5.2 KW heaters connected in STAR formation between the 3 Phases and

Neutral. The three pairs of Heater wires are brought to the terminal block in the POWER INPUT BOX ,

labelled as follows:

Wires No 04, 05, 06 or red, yellow, blue group [0] =Heater (NEUTRAL)#1,2,3

Wires No 01,02,03or red,yellow, blue group [3] = Heater (FEED)#1,2,3

POWER SUPPLY CONNECTIONS 380-440 Volt 3-Phase:

16Kw & 12 Kw models with Red-Yellow-Blue power wiring

Power Supply is connected as shown in Appendix 1, Fig.6.

NOTE..THE NEUTRAL LINE MUST NOT BE FUSED.

MODELS FOR 200/240 VOLT 3-PHASE SUPPLY

Export Models For Countries Where Domestic Supply Is 110v Line - Neutral

This Voltage Operation is denoted by Order Code AAN110 or AAN111. These models are not

normally supplied with a fitted power supply cable.

Connect the Power Supply as shown in Appendix 1, Fig.6.

In these models the heaters are the standard (240 volt), 3.3, 4 or 5.2 KW types, wired to operate in 3-

phase DELTA formation. The heater wires are brought to the Contactor in the Power Input Box and

are labelled:-

Wire No. 04, 05, 06 or Red,Yellow,Blue Group [3]= LINE B for Heater #1,2,3

Wire No.01,02,03 or Red,Yellow,Blue Group [0] = LINE A for Heater #1,2,3

The Heaters are wired in the factory Phase-To-Phase as in Appendix 1, Fig. 2

A BALANCED NEUTRAL SUPPLY MUST BE PROVIDED

The internal electronics and control actuators operate from 240 volts supplied by a step-up internal

transformer between Phase 1 and Neutral.

3-Phase Motors are normally dual voltage, wired in delta formation for 200-220v.

Single-phase motors are normally 230V motors wired between two phases. These have fuses in each

supply line.

200-220v 3-PHASE SUPPLIES WITHOUT NEUTRAL

This is option AAN111 . It is electrically as option AAN110 , but requires no Neutral supply.

Connect as described above but omit the Neutral connection.

The internal electronics uses a 220V supply derived from two Phases @ 200-220v via an internal

Isolating Transformer.

CONVERSION

It is possible to convert a SWIFTCLAVE from 380-440 v to 200-220 v supplies or in

reverse. This requires the fitting of a special transformer unit and detailed wiring

changes, and requires the services of a factory-trained qualified engineer.

PDF created with FinePrint pdfFactory Pro trial version http://www.fineprint.com

Altri manuali Astell Attrezzature da laboratorio

Astell

Astell AMB220 Manuale utente

Manuali Attrezzature da laboratorio popolari di altre marche

Qiagen

Qiagen DML 3000 Manuale utente

Queensgate

Queensgate NANOSCAN OP400 Manuale di programmazione

Conviron

Conviron GEN1000-GE Manuale utente

Parr Instrument

Parr Instrument 4560 Manuale di istruzioni

IKA

IKA IC control Manuale utente

Integra

Integra DOSE IT Manuale utente

Agilent Technologies

Agilent Technologies 5800 ICP-OES Manuale utente

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manuale utente

NI PXI-5422 Manuale

Collomix

Collomix Aqix Manuale utente

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manuale utente

Ocean Insight

Ocean Insight FLAME-NIR+ Manuale utente

Parker

Parker ALIGN-MG-NA Manuale utente

BD 644787 Manuale utente

DENTAURUM

DENTAURUM Compact Megaplus Manuale utente

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manuale utente

VWR

VWR SAS Super IAQ Manuale utente

illumina

illumina MiSeqDx Manuale utente