Atlantic 63607076 Manuale utente
1
Before proceeding please make sure your kit has the following items.
1 x One Arm TV Mount
(two assembly options)
2 x 8.66 in. (220 mm) Velcro Cable Ties
1 x 6 ft. HDMI 3D+Ethernet
1 x 9 ft. HDMI 3D+Ethernet
1 x Cleaning Spray Bottle (6.8 oz.) with
1 x 8 in. Microber Cloth
1x 6 Outlet Surge Protector
8
G
2
M8X16 mm
M6X12 mm
M5X12
M4X12
M8X40
M6X35
M5X30 mm
M4X30 mm
4
4
4
4
4
4
4
4
M4/M5 washer
M6/M8 washer
M8/M6 spacer
M4/M5 spacer
4
4
4
4
mm
mm
mm
mm
I
J
K
L
M
N
O
Q
R
S
T
TV Wall Mount
Parts List
Hardware List
Part #
Part # ItemItem Qty
Qty
H
B
A
C
F
2
1
1
1
4
Part # Part # ItemItem Qty
Qty
D2
P
Parts A and B are pre-assembled at the factory.
3
1/4”or 7 mm
Safety Glasses
Wood Drill Bit
¼ in or 7 mm
Drill
Phillips
Screwdriver
Stud Finder
TV Wall Mount
Tools Needed (not included)
4
2. Never let children climb on product or play with product.
3. Do not sit or stand on product.
4. Do not fasten a TV that is heavier than the recommended load rating to the mount.
1. If you do not understand these instructions, or have doubts about the safety of this
installation, contact customer service or call a qualied contractor. The manufacturer is
not liable for damage or injury caused by incorrect mounting, assembly or use.
5. The size and weight of your TV must not exceed 37 to 64 in. (93.98 to 162.56 cm) diagonally or
132 lbs (60 kg). The wall must be capable of supporting ve times the weight of TV plus the
mount.
.
6. The mount allows the TV to tilt +5° to -15°.
Minimum distance from wall: 3.07 in. / 78 mm
Maximum distance from wall: 21.65 in. / 550 mm
7. Improper handling can result in cuts and lacerations.
8. Images are for reference only.
1. This TV mount is designed for use on a vertical wall that is constructed with wood studs.
3. Make sure that all parts are in the box and in good condition.
4. Assemble the product on the open at carton or a rug to protect the product and
your oor.
5. Some heavy products need a second person to assist in the assembly. Do not install on a
sloping surface.
Caution:
Assembly Tips:
TV Wall Mount
2. Become familiar with the instructions and all parts.
5
Step 2
Installing wall bracket
This mount is designed to be attached into wood studs. DO NOT use wall anchors. Seek the assis-
tance of a professional installer to mount your TV without using wood studs.
Using a stud nder, nd the center of two studs. With a pencil, mark the two top hole locations
at te desired height making sure you are LEVEL. Hold wall bracket (A) against the wall and
mark the two lower hole locations. Drill four pilot holes at pencil marks 2.5 in. (64 mm) deep,
using a 1/4 in. or 7 mm diameter drill bit. Attach wall bracket (A) to the wall with four washers
and screws (F). DO NOT MOUNT INTO DRYWALL ONLY. MUST BE BOLTED TO STUDS.
16 in.
40.64cm
stud finder
Step 1
Disassembling parts
TV Wall Mount
Remove TV mounting plate (B) from wall bracket (A).
16”/406mm
A
Fx4
A
B
6
Carefully lay your TV on a rug or at carton. Attach TV mounting plate (B) to back of the TV, by
selecting the proper mounting hardware. Spacers are included if screws are too long for screw
holes. (See page 2.) Hand tighten screws until the plate is attached and aligned. Then tighten each
screw snugly.
Step 3a
Attaching mounting plate
TV Wall Mount
Step 4a
Installing TV on wall bracket
We strongly recommend two people, one on each side, lift the TV.1.
Carefully position TV over the wall bracket (A) until it locks in place.
2.
Tighten both safety screws.
3.
If you want to remove TV from the wall plate at a later time, you will need two people. One
person must hold the TV, while the second person loosens the two safety screws. Now with
one person on each side of the TV, remove the TV from the wall plate (A).
4.
safety
screws
B
OPTION 1
2.95 x 2.95 in/3.94 x 3.94 in (75 x 75 mm/100 x 100 mm)
Choose best installation option based on TV back panel hole spacing. See OPTION 2 on next page.
7
Step 4b
Attaching TV mount
H
Carefully lay your TV on a rug or at carton. Attach TV mounting assembly from Step 3b above
to back of the TV, by selecting the proper mounting hardware. Spacers are included if screws
are too long for screw holes. (See page 2.) Hand tighten screws until the plate is attached and
aligned. Then tighten each screw snugly.
Step 3b
Assembling TV mount
TV Wall Mount
Measure the hole spacing on the back of your TV. Position two TV mounts (C) onto horizontal
attachment arms (D) at the same spacing you measured. Using Allen wrench (H), attach both
TV mounts (C) to attachment arms (D) with 4 screws (G).
Using Allen wrench (H), attach TV mounting plate (B) to attachment arms (D) with 4 screws (G).
OPTION 2
(7.87 to 23.6 in) x 15.7 in (200 to 600) mm x 400 mm
Choose best installation option based on TV back panel hole spacing.
D
B
Gx4
C
Gx4
8
Step 5b
Installing TV on wall bracket
TV Wall Mount
We strongly recommend two people, one on each side, lift the TV.1.
Carefully position TV over the wall bracket (A) until it locks in place.
2.
Tighten both safety screws.
3.
If you want to remove TV from the wall plate at a later time, you will need two people. One
person must hold the TV, while the second person loosens the two safety screws. Now with
one person on each side of the TV, remove the TV from the wall plate (A).
4.
safety
screws
OPTION 2
9
UL Listed to U.S
Standards: UL 1449, UL 498A
Technical Specications:
Surge Protector
Operation Instructions:
Electrical Rating: 15A, 120 VAC, 60 Hz, 1800 Watts
Surge Lines Protected: 3-Line (L-N, L-G, N-G)
UL Clamping Voltage: L-N 500 V, L-G 500 V, N-G 500 V
Maximum Energy Dissipation: 900 Joules
Maximum Spike Current: 45,000 Amps (3 Line Total)
Response Time: <1 Nanosecond
EMI/RFI Noise Filter:
Frequency: 100 kHz ~ 100 mHz
Attenuation: Up to 40 dB
Plug Surge Protector into wall outlet rst,
and then plug in electrical equipment
and connect coax cables.
Disconnect all electrical equipment
before removing Surge Protector from
wall outlet.
Caution:
Indice
Altri manuali Atlantic Supporto TV
