Atlas BP10000 Manuale utente

Rev. 12/12/2017

Read this entire manual before operation begins.

Record below the following information which is located on the serial number

data plate.

Serial No.

Model No.

Date of Installation

Contents

Speciﬁcations . . . . . . . . . . . . . 4

Installation Requirement . . . . . . . 6

Installation Steps . . . . . . . . . . . 8

Test Run . . . . . . . . . . . . . . . 22

Operation Instructions. . . . . . . . . 24

Maintenance Schedule. . . . . . . . . 25

Trouble Shooting . . . . . . . . . . . 26

Parts Breakdown . . . . . . . . . . . 27

Warranty . . . . . . . . . . . . . . . 35

Specifications 4

BP10000

Speciﬁcations

Floorplate Chain-Drive Two Post Lift

Model BP10000X

• Compact design

• Dual hydraulic cylinders, designed and made on ANSI standards, utilizing

NOK oil seal in cylinder

• Self- lubricating UHMW Polyethylene sliders and bronze bush

• Single-point safety release, and dual safety design

• Stackable rubber pad with 1.5”, 2.5” and 5” extension adaptors

• Super-symmetric arms design with 3-stages front arms and 2-stages rear

arms

Fig. 1

Specifications 5

BP10000

BP10000 Speciﬁcations

Style Lifting

Capacity Lifting

Time Lifting Height Overall

Height Overall

Width

Between

Columns

Minimum

Pad Height

Gross

Weight Motor

Floor plate

Chain-drive

4.5T

10,000lbs 62S 1965-2194mm

77 3/8”–86 3/8”

2841mm

111 7/8”

3534mm

139 1/8”

2850mm

112 1/4”

115mm

4 1/2”

745Kg

1640lbs 2.0/3.0 HP

Arm Swing View

Fig. 2

Installation Requirement 6

BP10000

Installation Requirement

Tools Required

Rotary Hammer Drill (3/4”) Carpenter’s Chalk

Hammer Screw Drivers

Level Bar Tape Measure (25ft)

Crescent Wrench (12”) Pliers

Ratchet Spanner With Socket (28#) Allen Head Wrench (6#)

Wrench set (mm)

(10#, 13#, 14#, 15#, 17#, 19#, 24#, 27#)

Vise Grips

3.5 to 5 Gallons of AW32 - AW46 Hydraulic Oil is recommended for operation

Fig. 3

Installation Requirement 7

BP10000

Speciﬁcations Of Concrete

Speciﬁcations of concrete must be adhered to the speciﬁcation as following.

Failure to do so may result in lift and/or vehicle falling.

1. Concrete must be thickness 100mm minimum and without reinforcing steel

bars, and must be dried completely before the installation.

2. Concrete must be in good condition and must be of test strength 3,000psi

(210kg/cm²) minimum.

3. Floors must be level and no cracks.

Fig. 4

Power Supply

The electrical source must be 2.2KW minimum. The source cable size must be

2.5mm² and in good condition of contacting with ﬂoor.

Installation Steps 8

BP10000

Installation Steps

A. Location Of Installation

Check and insure the installation location (concrete, layout, space size etc.) is

suitable for lift installation.

B. Use A Carpenter’s Chalk Line To Establish

Installation Layout Of Baseplate

Fig. 5

Check The Parts Before Assembly

1. Packaged lift, hydraulic power unit and parts box (See Fig. 6).

Fig. 6

Installation Steps 9

BP10000

2. Move aside the lift with fork lift or hoist, open the outer packing, take out the

parts from the column and check the parts with shipment list (See Fig. 7).

Fig. 7

3. Loose the bolts of the upper package stand, remove the upper column then

remove the package stand.

4. Move the parts aside and check the parts according to the shipment parts list.

Fig. 8

Metal Serial No.

Floor cover

Parts box

Shipment

Parts list

Parts box (83)

Fig. 9

Installation Steps 10

BP10000

5. Check the parts of the parts bag according to parts bag list (See Fig. 10).

Fig. 10

D. Position Power Side Column

Lay down two columns on the installation site parallel, position the power

side column according to the actual installation site and install top plate, top

connecting plate assy.. Usually, it is suggested to install power side column on

the front-right side from which vehicles are driven to the lift (See Fig. 11).

Fig. 11

Power side column

Car-in direction

Offside column

Install top connecting

plate with M8*20 hex bolt,

nut and lock washer

Altri manuali per BP10000

Indice

Manuali Sistema di sollevamento popolari di altre marche

morse

morse 82H-124 Manuale utente

Braun

Braun NL955 Series Manuale utente

haacon

haacon 1889.10 Manuale utente

Protekt

Protekt AT 252 Manuale utente

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Manuale utente

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Manuale utente

Genie

Genie Z-60/34 Manuale utente

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Manuale utente

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Manuale utente

Custom Equipment

Custom Equipment Hy-Brid 3 Series Manuale di programmazione

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Manuale di programmazione

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Manuale di programmazione

BERG

BERG BeNomic EasyLeaf Manuale utente

Powermate

Powermate LiftGate LG-3 Manuale utente

Snorkel

Snorkel TM12 Series Manuale utente

Terberg

Terberg OMNIDEKA Manuale utente

Harmar Mobility

Harmar Mobility AL625 Istruzioni operative

Rotary

Rotary SPO16 Manuale utente