Atmel ATSAMB11 BluSDK SMART Manuale utente

ATSAMB11 BluSDK SMART

Alert Notification Profile - Getting Started Guide

USER GUIDE

Introduction

The Alert Notification Profile allows a device like a watch to obtain information from a cellphone about

incoming calls, missed calls, and SMS/MMS messages. The information may include the caller ID for an

incoming call or the sender’s ID for email/SMS/MMS but not the message. This profile also enables the

client device to get information about the number of unread messages on the server device.

The iPhone®implements a custom variant of ANS called ANCS. A separate example application

implementing this custom variant is available in the BluSDK SMART package.

The example application explained in this document will only work with BLE compatible Android phones

running Atmel SmartConnect mobile application. Unlike iPhone, Android does not natively support Alert

Notification Service. The Atmel SmartConnect mobile application implements this service and can be

used to demonstrate this example application. The example application supports missed call alert and

SMS alert notification.

The device implements the GATT Client, which reads (or gets notified) about the characteristic values

from the GATT server (the mobile device). The Atmel®ATSAMB11 device must be paired with an Android

phone. After connection and discovery, missed call or SMS alert notifications can be enabled/disabled.

The Atmel SmartConnect application will notify missed calls or SMS alerts, which are then displayed on

the terminal console on the device side. The following chapters provide a detailed description of running

this demo.

The ‘SW0’ user button on the ATSAMB11 is programmed in such a way that each successive button

press will either enable or disable the notifications.

Features

Device Discovery and Disconnection

Pairing/Bonding

Alert Notification Service

Alert on incoming call

Atmel-42609A-ATSAMB11-BluSDK-SMART-Alert-Notification-Profile-Getting-Started-Guide_UserGuide_112015

ATSAMB11 BluSDK SMART –Alert Notification Profile –Getting Started Guide [USER GUIDE]

Atmel-42609A-ATSAMB11-BluSDK-SMART-Alert-Notification-Profile-Getting-Started-Guide_UserGuide_112015

Table of Contents

1Purpose .....................................................................................................................3

2Demo Setup..................................................................................................................3

3Hardware Setup ...........................................................................................................3

4Software Setup.............................................................................................................4

4.1 Installation Steps...................................................................................................................................4

4.2 Build Procedure.....................................................................................................................................4

5Console Logging .........................................................................................................6

6Running the Demo.......................................................................................................6

7BluSDK SMART Software Architecture....................................................................10

8ATMEL EVALUATION BOARD/KIT IMPORTANT NOTICE AND DISCLAIMER........11

9Revision History ........................................................................................................12

ATSAMB11 BluSDK SMART –Alert Notification Profile –Getting Started Guide [USER GUIDE]

Atmel-42609A-ATSAMB11-BluSDK-SMART-Alert-Notification-Profile-Getting-Started-Guide_UserGuide_112015

1 Purpose

This getting started guide describes the setup of an Atmel ATSAMB11 Xplained board and bringing up an

example profile supplied as part of BluSDK SMART release. The Alert Notification Profile is an example

application that is embedded as part of the software release package.

This document explains the details about:

1. Getting started with the setup of ATSAMB11 to be used as a Notification Consumer.

2. Getting the ANS Application working on the above mentioned setup.

The example application provided currently supports ‘Missed Call Alert and SMS Notification’.

2 Demo Setup

3 Hardware Setup

Connect the ATSAMB11 board to the host PC using a Micro-USB cable.

Figure 3-1. EDBG USB Port

BLE Link

Android phone

Atmel SmartConnect app

(Notification Provider)

ATSAMB11

(Notification Consumer)

ATSAMB11 BluSDK SMART –Alert Notification Profile –Getting Started Guide [USER GUIDE]

Atmel-42609A-ATSAMB11-BluSDK-SMART-Alert-Notification-Profile-Getting-Started-Guide_UserGuide_112015

4 Software Setup

4.1 Installation Steps

1. Install the latest Atmel Studio [Atmel Studio 7.0 (build 629 or later) web installer

(recommended)]

http://www.atmel.com/tools/ATMELSTUDIO.aspx.

2. Install the latest Atmel Software Framework.

This package will install the following examples within the Atmel Studio environment:

Alert Notification application for ATSAMB11

4.2 Build Procedure

The following procedure is explained for ATSAMB11 application example.

1. Select New Example Project.

Figure 4-1. Creating a New Example Project

2. Select “SAMB11” in device family, enter “alert notification” in search window, and expand Atmel

Corp Projects. The location and the name of the project can be selected in the respective fields.

Click OK.

Figure 4-2. Selecting Alert Notification Application from Example Projects

3. Accept the license Agreement. The Atmel studio will generate the Alert Notification Profile project

for ATSAMB11.

4. Build the solution.

ATSAMB11 BluSDK SMART –Alert Notification Profile –Getting Started Guide [USER GUIDE]

Atmel-42609A-ATSAMB11-BluSDK-SMART-Alert-Notification-Profile-Getting-Started-Guide_UserGuide_112015

Figure 4-3. Building the ANP Application

5. Download the application via the USB to the ATSAMB11 board by using the Device Programing

option available in Tools as shown below.

Figure 4-4. Flashing the Application on Atmel MCU

6. Inside the device programming the user has to select the correct configuration for the device and

finally program the device by using the program button.

Figure 4-5. Flash Programming

7. Once the application is flashed, now ANP Application is ready for usage.

ATSAMB11 BluSDK SMART –Alert Notification Profile –Getting Started Guide [USER GUIDE]

Atmel-42609A-ATSAMB11-BluSDK-SMART-Alert-Notification-Profile-Getting-Started-Guide_UserGuide_112015

5 Console Logging

For the purpose of debugging, a logging interface had been implemented in the ANS Application.

The logging interface utilizes the same EDBG port that connects to ATSAMB11. A serial port monitor

application (for example TeraTerm) shall be opened and attached to the corresponding COM port

enumerated on the PC by the device. Baudrate should be set to 115200.

6 Running the Demo

1. Open a console window using TeraTerm or any equivalent serial port monitor application and

connect to the corresponding COM port enumerated on the PC. Configure the COM Port with the

following settings: Baudrate 115200, Parity None, one Stop bit, one Start bit, no Hardware

Handshake.

2. Press the Reset button on the ATSAMB11 board.

3. The device is now in advertising mode.

Figure 6-1. Display for Advertising Mode

Initializing Alert Notification Profile Application

Initializing SAMB11

BD Address:0xF8F005F23FFF, Address Type:0

Device is in Advertising Mode

4. On the Android phone, enable Bluetooth®in the Settings page. Start the Atmel SmartConnect

mobile application and allow it to scan for devices. ATMEL-ANS will appear amongst the devices

scanned. Click on ATMEL-ANS to connect to the ATSAMB11 device.

Figure 6-2. ATMEL-ANS Device Discovery on Atmel SmartConnect Application

ATSAMB11 BluSDK SMART –Alert Notification Profile –Getting Started Guide [USER GUIDE]

Atmel-42609A-ATSAMB11-BluSDK-SMART-Alert-Notification-Profile-Getting-Started-Guide_UserGuide_112015

5. Once connected, the client side will request for the pairing procedure with the Android phone. The

console log provides a guidance for the user to enter the pass-key on the phone.

Figure 6-3. Figure 9: Console Display for Pairing in ANP

Alert Notification Profile Application

Initializing SAMB11

BD Address:0xF8F005F23FFF, Address Type:0

Device is in Advertising Mode

Connected to peer device with address 0xccfa00710852

Connection Handle 0

Peer device request pairing

Sending pairing response

Please Enter the following Pass-code(on other Device):123456

Pairing procedure completed successfully

6. On Android phone side, a pop-up screen prompting the user to enter the pass-key will appear.

Enter ‘123456’ in the text box and click on ‘Pair’.

Figure 6-4. Pairing Pop on Android Phone

ATSAMB11 BluSDK SMART –Alert Notification Profile –Getting Started Guide [USER GUIDE]

Atmel-42609A-ATSAMB11-BluSDK-SMART-Alert-Notification-Profile-Getting-Started-Guide_UserGuide_112015

7. After pairing the Alert Notification service page is displayed as shown.

Figure 6-5. ANS Services Page

8. Enable the notifications by using the SW0 button. The mobile app should reflect the status as

shown.

Figure 6-6. Alert Notification Screen on Atmel SmartConnect Application

ATSAMB11 BluSDK SMART –Alert Notification Profile –Getting Started Guide [USER GUIDE]

Atmel-42609A-ATSAMB11-BluSDK-SMART-Alert-Notification-Profile-Getting-Started-Guide_UserGuide_112015

9. The user can trigger a missed call to the Android phone or send an SMS. The corresponding

notification then gets displayed on the ATSAMB11 side as shown below in the console logs.

Figure 6-7. Alert Notification Screen on Atmel SmartConnect Application

New Alert received

The no of new alerts are 1

The alert type is :

Missed Call alert

Unread alert received

The no of unread alerts are 0

New Alert received

The no of new alerts are 2

The alert type is :

Missed Call alert

Unread alert received

The no of unread alerts are 1

The alert type is :

Missed Call alert

ATSAMB11 BluSDK SMART –Alert Notification Profile –Getting Started Guide [USER GUIDE]

Atmel-42609A-ATSAMB11-BluSDK-SMART-Alert-Notification-Profile-Getting-Started-Guide_UserGuide_112015

7 BluSDK SMART Software Architecture

Figure 7-1 illustrates the top level diagram for the ATSAMB11 configuration.

Figure 7-1. ATSAMB11 Software Architecture

Altri manuali per ATSAMB11 BluSDK SMART

Indice

Altri manuali Atmel Hardware per computer

Atmel

Atmel ATAN0008 Manuale utente

Atmel

Atmel AT90USB162 Manuale utente

Atmel

Atmel AT85DVK-07 Manuale utente

Atmel

Atmel STK502 Manuale utente

Atmel

Atmel FPSLIC ATSTK94 Manuale utente

Atmel

Atmel AVR ISP Manuale utente

Atmel

Atmel AT90ICEPRO Manuale utente

Atmel

Atmel Dual Triple DMOS Output Drivers with Serial Input and PWM Control... Manuale utente

Atmel

Atmel AT86RF211 Manuale utente

Atmel

Atmel STK501 Manuale utente

Atmel

Atmel AVR AT90S8515-4 Manuale utente

Atmel

Atmel REB233-XPRO Manuale utente

Atmel

Atmel AVR ATmegaICE Manuale utente

Atmel

Atmel ATSAMB11 BluSDK SMART Manuale utente

Atmel

Atmel AT24C16C Manuale utente

Atmel

Atmel SAMA5D3 Series-EK Manuale utente

Atmel

Atmel FPSLIC AT94KAL Series Manuale utente

Atmel

Atmel AT73C246-EK1 Manuale utente

Atmel

Atmel AT76C502A Manuale utente

Atmel

Atmel AVR XMEGA 8/16-bit High Performance Low Power Flash... Manuale utente

Atmel

Atmel ATAK2270 Manuale utente

Atmel

Atmel AT89C5132 Manuale utente

Atmel

Atmel ATSTK94 Istruzioni operative

Atmel

Atmel ATF16V8B Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente