Atop EW5300 Manuale utente
Atop Technologies, Inc.
Wireless Client Adaptor
EW5300
Quick Start Guide
Version 1.1
Updated on Sept. 14, 2010
Overview
The EW5300 have one Ethernet port to connect to IEEE
802.11 b/g wireless network. It is ideal to create a
“bridge” for an Ethernet device that has an Ethernet
interface to a wireless network. By using EW5300, these
devices can be communicated over a wireless network
to send or receive the information from, e.g., a backend
server or database. This document intends to provide
customers with brief descriptions about the product and
to assist customers to get started. For detailed
information and operations of the product, please refer
to the product user’s manual in the Product CD.
Packaging Included
Atop EW5300 Wireless ClientAdaptor
3-Pin Terminal Block for Power Connector
(TB model only)
4 dBi Antenna
Atop EW5300 Quick Start Guide with Product
Warranty Card
Product CD (User’s Manual and Utility Software)
Wall mount kits x 2 (optional)
Hardware Setup
The following figure shows the components on the panel
of EW5300.
*Reset Button: Press Reset button continuously over
sec to reload the device to the factory default settings.
3
LED Indications
The LEDs indicate the status of EW5300. Please see
the front panel
Name Color Status Description
Red*2 ON Its strength is poor, but the
link is connected for the
wireless link
Yellow*2 ON Its strength is good, the
wireless link can supply a
good transfer channel
Signal
Strength
Green*2 ON Its strength is very excellent
and the link is connected on
best status
Off Wireless Link is Broken or
No data transmit or receive
via wireless connectivity
WLAN Green
Blink Wireless Traffic be indicted
for data transfer
OFF/ON System is not ready or halt
RUN Green Blink System is running and LED
is blink per 0.5 sec
Hardware Installation
Step 1: Connect the device with the antenna and to a
LAN switch with a standard UTP/STP cable.
Step 2: Attach the power wire to the device for 9~48V
DC, and confirm the power polarity carefully.
Please check the Terminal Block diagram for
power supply to connect the device to a power
supply.
Step 3: Wait for the device to start up after 60 seconds,
and see the next section for network
configuration
UL Notice for Power supplier
EW5300 series products are intended to be supplied by
a Listed Power Unit marked with “LPS”, “Limited Power
Source” or “Class 2” and output rate 9~48VDC, 1A
minimum. Otherwise, use the recommended power
supply in “OptionalAccessories.
Network Configuration
There are two steps to configure the device. First, you
need to find the device in your network using our
software tool, Deviceview. Once the device is properly
configured with a new IP address; you can further
configure the device’s wireless network interface using a
web browser or a telnet terminal.
Configure using Deviceview software
Use Deviceview that comes with Product CD to
configure the network parameters of EW5300. Please
refer to Appendix A Deviceview Configuration Utility
in the product user’s manual for more details.
Terminal
Block for DC
Power
Antenna
Connecto
r
Wireless
Status LEDs
System/WLAN
Status LED
Reset
10/100M
Ethernet
Step 1: Scan a new device by clicking the scan button
Step 2: Get the device’s current IP address from table
list after scanning, and login using the default
username: admin and default password:
(leave it blank)
Step 3: Re-assign an IP address, network mask and
gateway if needed.
Step 4: Then, you can configure a wireless network
interface using a web browser or a telnet
terminal.
Warning: Please avoid connecting LAN and WAN
interface to the same network. This may incur
unexpected networking problem.
Automatic IP Address using DHCP
To avoid any IP address conflict, an automatic IP
address assignment should be used. A DHCP server
can automatically assign an IP address, subnet mask,
and gateway address to EW5300 device. This function
is disabled by default. Please see the user’s manual
for more details.
Configure using Web Browser
Step 1:Open a web browser and type in the IP address
of the device in URL field. A dialog is prompt for
a username and a password. The default
username is admin and the password is null
(leave it blank).
Step 2:Configure network settings from web page links
then click “Save Configuration” to save
settings.
Step 3:Click on ”Restart” button to make the change
effective
Configure using Telnet terminal program
Step 1:Telnet to the device using command shell of
Windows (StartÆRun) or any other terminal
program that supports Telnet. Then, type in
“telnet 10.0.50.100”. The 10.0.50.100 is the
default IP address of the device. You will need to
change it to a new IP address if you have
assigned a new IP address to the device. Then,
type in and default password is null (leave it
blank).
Step 2:Configure the wireless network interface by
selecting the items on the main menu on the left
side of the device’s web page.
Warranty Policy
Warranty Conditions
Products supplied by Atop Technologies are covered
in this warranty for sub-standard performance or
defective workmanship. The warranty is not, however,
extended to goods damaged in the following
circumstances:
(a) Excessive forces or impacts
(b) War or an Act of God: wind storm, fire, flood,
electric shock, earthquake
(c) Use of unqualified power supply, connectors, or
maintenance procedure
(d) Replacement with unauthorized parts
RMA and Shipping Costs Reimbursement
Customers shall always obtain an authorized "RMA"
number from Atop before shipping the goods to be
repaired to Atop. When in normal use, a sold product
shall be replaced with a new one within 3 months after
purchase. The shipping cost from the customer to Atop
will be reimbursed by Atop.
After 3 months and still within the warranty period, it is
up to Atop whether to replace the unit with a new one;
normally, as long as a product is under warranty, all
parts and labor are free of charge to the customers.
After the warranty period, the customer shall cover the
cost for parts and labor.Three months after purchase,
the shipping cost from the customer to Atop will not
be reimbursed, but the shipping cost from Atop to the
customer will be paid by Atop.
Limited Liability
Atop shall not be held responsible for any
consequential losses from using Atop’s
product.
Warranty Period
Product Categories Warranty
Serial-to-Ethernet Server
Serial-to-WLAN Server
Industrial Wireless Ethernet Device
Modbus Gateway Series
Industrial Ethernet Switch
Embedded Serial Server
5 Years
Pick-to-Light System
Auto-Identification and Data
Collection-AIDC
1 Year
*Notes: Warranty coverage for Accessories such as
power adaptors and high-gain antenna is one year.
The Warranty Certification will not be effective until an
authorized stamp issued byAtop’s overseas agents.
PurchaseDate: / / (yyyy/mm/dd)
Serial Number:
※ATOP Customer Services and Supports
1. Please contact your local dealers orAtop technical
support center at the following numbers.
y+886-3-550-8137 (Atop Taiwan)
y+86-21-6495-6232 (Atop China)
2. Please report the defected problems viaAtop’s Web
site or E-mail account
Web Site:www.atop.com.tw e-mail: [email protected]w
Web Site:www.atop.com.cn e-mail: [email protected]
Altri manuali per EW5300
1
Altri manuali Atop Ricevitore
