Attwood 3100 Manuale utente

Quasar 12-Volt 2-Mile

Navigational Light

Without Wire Leads: 3100-3104, 3130-3134

With 7" Wire Leads: 3120-3124, 3150-3154

Attwood marine hardware, navigational lighting, bilge pumps, and other

marineaccessoriesarespecifiedmorethananyotherbrandbyAmerica’s

best-known boat manufacturers as original equipment. Look to Attwood

for quality replacement parts and marine accessories.

SAVE THESE INSTRUCTIONS

Form Number 69385 Rev. B 03-10

Meets USCG CFR 183.810, ABYC A-16 requirements, and

all applicable standards as tested by Imanna Labs, 7/8/1995.

2 Nautical Mile visibility. Uses 9230-7 Lamp, 13V, 8 Watt.

FEATURES

The new Attwood 12-volt DC Quasar two-mile navigational sidelights

are designed for mounting on horizontal surfaces, such as the gunwale

or deck. They meet the ABYC Standard A-16, COLREG 72, and

other selected international standards.

REQUIRED FOR INSTALLATION

The stylish housing is supplied in UV-stable, color-matched

polycarbonate or chromed HIPP (High Impact Electroplated

Plastic). The lens completely encapsulates the bulb and socket

assembly for splash resistance. When used with the optional base

gasket, these lights are virtually waterproof.

•Screwdriver.

•Drill with suitable bits — 1-¹⁄₈" (29mm).

• Base gasket (Attwood # 910467) or marine sealant.

• Three #8 or #10 stainless steel pan head screws.

LOCATION

1. Position light(s) on a horizontal surface (±5°) of the gunwale or

deck. If installing a combination light, place it on the furthermost

tip of the bow on the centerline of the boat. (See Figure 1a.)

If installing sidelights, the red lens must be on the port (left) and

the green on the starboard (right) as you stand onboard facing

the bow of the boat. (See Figure 1b.)

3. Measure and mark location of terminal clearance hole. Be

certain that centerline of hole is aligned with boat centerline.

Drill a 1-¹⁄₈" (29mm)-dia. hole. (See Figure 2.)

112.5°Arc Must Be Clear

Red

(Port) Green

(Starboard)

2. Ensure that there are no front or side obstructions, such as rail

stanchions, chocks, anchors, etc., within the arc of visibility

(112.5°each side).

MOUNTING INSTRUCTIONS

1. To access mounting holes inside the base: Loosen retaining

screw one full turn; lift rear of cover, use flat base screwdriver if

necessary to raise rear, rotate cover up and forward to unlock;

twist lens counterclockwise and remove.

2. Place base into hole and align front and back with the boat

centerline. Use base to mark pilot holes for the mounting screws.

Drill pilot holes.

3. Feed the power source terminals up through the deck and attach

to base terminals. Insulated terminals are recommended.

CAUTION

Position carefully on aluminum boats so that wires do not contact

the hull.

4. Apply gasket (Attwood # 910467) or sealant to deck mounting

area. Gasket is highly recommended on aluminum surfaces.

Place base over the drilled holes.

5. Insert three stainless steel pan head mounting screws through

base and fasten into deck. Replace lens, push cover down over

front of lens lock - rotate back and down. Snap cover down into

position and tighten the retaining screw. (See Figure 3.)

Figure 1a Figure 1b

Figure 3

Red

(Port) Green

(Starboard)

Figure 2

(Applies to Quasar Light, not Snap Base)

FORWARD

13/16"

(21mm)

9/16"

(14mm)

(25mm)

15/16"

(24mm)

2-1/4"

(57mm)

1-1/8"

(29mm)

••

•

•• • •

•

Housing

•Lock Catch

Lens

•Lens

•

Lock

Lock Detail

•Lock

Mounting Screws

(Not Supplied)

8-Watt

Festoon Bulb Retaining Screw

•

Screwdriver Slot

•

•Boat Centerline

2. Test lights for proper operation from dash-mounted control

switch.

MAINTENANCE

Replace bulb, when necessary, with standard 8-watt automotive

festoon type (Attwood #9230-7).

WIRING INSTRUCTIONS

The power source must be 12-volt DC ONLY. Use marine

grade wire connectors only. Protect all connections with suitable

materials.

NOTE: Failure to make proper connections and fuse the light

properly will void the product warranty.

1. Connect one terminal to the negative ( - ) post of the 12-volt

battery. Connect the other terminal to the positive ( + ) lead

through a 2-amp fuse and suitable dash-mounted switch. (See

Figure 4.)

Switch

•

2-Amp

Fuse

•

Figure 4

by Attwood of any product returned or any refund provided by Attwood shall

not be deemed an admission that the product is defective or in violation of

any warranty. Products that are replaced or for which a refund is issued

become the property of Attwood.

THIS WARRANTY IS ATTWOOD’S ONLY EXPRESSED WARRANTY OF

THESE PRODUCTS. NO IMPLIED WARRANTY INCLUDING, WITHOUT

LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE, SHALL BE EXTENDED

BEYOND THE WARRANTY PERIOD STATED ABOVE FOR EACH

PRODUCT. ATTWOOD SHALL NOT BE LIABLE FOR ANY DAMAGES,

FOR LOSS OF USE OF THIS PRODUCT, NOR FOR ANY OTHER

INCIDENTAL OR CONSEQUENTIAL DAMAGES, COSTS, OR EXPENSES.

Some states do not allow limitations on how long an implied warranty lasts

or the exclusion or limitation of incidental or consequential damages, so the

above limitations and exclusions may not apply to you. This warranty gives

you specific legal rights, and you may have other rights which vary from

state to state.

Figure 3a

(Optional Mount with Snap Base)

SAVE THESE INSTRUCTIONS

ATTWOOD LIMITED WARRANTY Attwood Corporation, 1016 North

Monroe, Lowell, Michigan 49331 (“Attwood”) warrants to the original

consumer purchaser that Attwood brand products will be free from defects

in materials and workmanship under normal use and service for one year

from the date of original consumer purchases.

This limited warranty is not applicable if the product has been damaged by

accident, improper installation, unreasonable or improper use, lack of proper

maintenance, unauthorized repairs or modifications, normal wear and tear,

or other causes not arising out of defects in materials or workmanship.

Attwood products are warranted for use on pleasure boats. Any other use—

including but not limited to commercial, racing, or non-marine use—are not

covered under this warranty. Attwood’s obligation under this warranty is

limited to repair of the product at Attwood’s plant or replacement of the

products at Attwood’s option without expense to the original consumer

purchaser. Any expenses involved in the removal, reinstallation or transpor-

tation of the product are not covered by this warranty.

The product must be returned to Attwood’s plant at the address above,

postage pre-paid, and insured with proof of original purchase including date.

If Attwood is unable to replace the product and repair is not commercially

practical or cannot be timely made, or if the original consumer purchaser is

willing to accept a refund in lieu of repair or replacement, Attwood may

refund the purchase price, less an amount for depreciation. The acceptance

(For ease of installation without disassembly of light.)

Product Part Number

1/4" Snap Base 3300 (Black)

3301 (White)

3302 (Gray)

3304 (Cream)

1" Snap Base 3310 (Black)

3311 (White)

3312 (Gray)

3314 (Cream)

Gasket 912010

(Installs between Light Assy and Snap Base)

Light Assembly

Mounting Screws

(Not Supplied)

Connecting Posts

Snap Base 1/4" or 1"

(6mm or 25mm)

Boat Centerline

Forward

1016 N. Monroe Street, Lowell, MI 49331-0260 www.attwoodmarine.com

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Attwood Illuminazione marina

Attwood

Attwood 3800 Series Manuale utente

Attwood

Attwood 6510 Series Manuale utente

Attwood

Attwood 6375D Manuale utente

Attwood

Attwood 6316 Manuale utente

Attwood

Attwood 6556 Manuale utente

Attwood

Attwood 911339 Manuale utente

Attwood

Attwood 91041 Manuale utente

Attwood

Attwood 66318 Manuale utente

Attwood

Attwood Pulsar 5040 Manuale utente

Attwood

Attwood 6320 Series Manuale utente

Attwood

Attwood 3560 Manuale utente

Attwood

Attwood 3830 Manuale utente

Attwood

Attwood 5300 Series Manuale utente

Attwood

Attwood 5530 Series Manuale utente

Attwood

Attwood 7800 Series Manuale utente

Attwood

Attwood 3592 Manuale utente

Attwood

Attwood 5550 Series Manuale utente

Attwood

Attwood 6340 Series Manuale utente

Attwood

Attwood 14060 Manuale utente

Attwood

Attwood 5100 Series Manuale utente

Attwood

Attwood 6510SS1 Manuale utente

Attwood

Attwood Quasar 3200 Manuale utente

Attwood

Attwood 3500 Series Manuale utente

Attwood

Attwood 91020 Manuale utente

Manuali Illuminazione marina popolari di altre marche

Francis Searchlights

Francis Searchlights FX560 Manuale utente

Glamox

Glamox aqua signal TX20 Series Manuale utente

Imtra

Imtra BCM California 60 Manuale utente

Sealite

Sealite SL60 Supplemento

Hella marine

Hella marine NAVILED PRO 2NM Manuale utente

ACR Electronics

ACR Electronics 3940 Istruzioni per l'installazione

ETI Solid State Lighting

ETI Solid State Lighting 504081020 Manuale utente

Sea gull lighting

Sea gull lighting Traverse Lyte Retrofit Kit Manuale utente

Sealite

Sealite SL-15 Supplemento

Daniamant

Daniamant W3-1 Manuale utente

Sabik Marine

Sabik Marine carmanah 800 Series Manuale utente

Tranberg

Tranberg TEF 2438N Manuale utente

Weems & Plath

Weems & Plath 700 Manuale utente

Hella marine

Hella marine NaviLED 360 2LT 980 960-0 Series Manuale utente

Hella marine

Hella marine NaviLED 360 PRO 2LT 980 910 Series Manuale utente

Hurley Marine

Hurley Marine LED Sea-Vue Manuale utente

Sealite

Sealite SL-300-2D5 Series Supplemento

ACR Electronics

ACR Electronics MS-2000(M) Istruzioni per l'installazione