AU SAE J1939 Manuale utente

Au SAE J1939 Simulator (Gen II) 2.00A

User Manual

Rev. D

Au Group Electronics

May 2009

All copyrights are reserved by Au Group Electronics. 1994-2009

This document can NOT be freely distributed without written approval from Au Group Electronics.

Au Group Electronics Au SAE J1939 Simulator (Gen II) 2.00A User Manual Rev. D

Table of Contents

Table of Contents ...............................................................................................................................................................2

Chapter 1 Introduction ..................................................................................................................................................3

1.1. J1939-15 Network Topology with Au J1939 Simulator...............................................................................3

1.2. Six Editions of Au SAE J1939 Simulators...................................................................................................3

1.3. Major Hardware Features.............................................................................................................................4

1.4. Major Operating Features.............................................................................................................................5

1.5. Basic Functions of Each Edition...................................................................................................................5

1.6. License /Software Code Upgrade and Support Service................................................................................6

Chapter 2 Supported SAE J1939 Parameters................................................................................................................7

2.1. Engine Basic Edition(S) ...............................................................................................................................7

2.2. Engine Premium Edition(S)..........................................................................................................................8

2.3. Vehicle Platinum Edition(S).........................................................................................................................8

Chapter 3 Operating Instructions ..................................................................................................................................9

3.1. Power On......................................................................................................................................................9

3.2. Operating Modes (Static/Dynamic)..............................................................................................................9

3.3. Push Button Functions..................................................................................................................................9

3.4. LED Indicator Status ..................................................................................................................................11

Chapter 4 Au J1939 Simulator Remote Terminal.......................................................................................................14

4.1. Step 1: Connect To J1939 Simulator..........................................................................................................16

4.2. Step 2: Remote Control the J1939 Simulator.............................................................................................17

4.3. Display Panel – Engine Idle Shutdown (Is)................................................................................................18

4.4. Display Panel – Engine Protection System (EPS)......................................................................................18

4.5. Display Panel – A/C & Refrigerant Switch................................................................................................18

4.6. Display Panel – Engine Info and Warning Lamps .....................................................................................19

4.7. Display Panel – Abs Info and Warning Lamps ..........................................................................................19

4.8. Display Panel – Transmission Info and Warning Lamps ...........................................................................19

4.9. Display Panel – Engine Basic Parameters..................................................................................................20

4.10. Display Panel – Engine DM1.....................................................................................................................21

4.11. Display Panel – Engine DM2.....................................................................................................................21

4.12. Display Panel – Engine Configuration.......................................................................................................23

4.13. Display Panel – Abs DM1..........................................................................................................................24

4.14. Display Panel – Transmission Dm1 ...........................................................................................................24

Chapter 5 Data Configuration.....................................................................................................................................25

Appendex A - Remote Terminal Installation Guide.........................................................................................................39

Appendex B - License Management Toolset ...................................................................................................................41

Appendex C - Au PIC Serial Bootloader Application Note.............................................................................................45

C-1 What’s needed Before Install Au PIC Bootloader?....................................................................................45

C-2 How to Install Au PIC Bootloader..............................................................................................................45

C-3 How to Use Au PIC Bootloader .................................................................................................................46

Au Group Electronics Au SAE J1939 Simulator (Gen II) 2.00A User Manual Rev. D

Chapter 1 Introduction

Au SAE J1939 Simulator (Gen II) 2.00A (Figure 1-1), a family of well designed devices, are capable of simulating

majority of SAE J1939 signals on a vehicle network. They can be connected to vehicle network at the 9 pin “BUS”

connector. The pinout of the DB9 male "BUS" interface is illustrated in Figure 1-2.

Figure 1-1 Au J1939 Simulator (Gen II) Figure 1-2 BUS Side DB9 male connector

1.1. J1939-15 Network Topology with Au J1939 Simulator

A typical SAE J1939-15 network topology with Au SAE J1939 Simulator is illustrated in Figure 1-3.

Figure 1-3 Typical SAE J1939-15 network topology for Au J1939 Simulator(s)

1.2. Six Editions of Au SAE J1939 Simulators

Six editions of Au SAE J1939 simulator (Gen II) 2.00A are provided to meet various users' needs (3 non-plus editions

and 3 plus editions). The Plus editions have all the functions of non-Plus editions, plus a PC Remote Terminal

program,which can be used to control and display detail information of simulated SAE J1939 signals on a PC screen

(detail information is available in chapter 4.)

Plus Edition =Non-plus Edition +PC Remote Terminal Program

This document will introduce major hardware features, important parameters, operating instruction, remote terminal

program and data configuration for all 6 editions of Au SAE J1939 Simulators (Gen II) 2.00A.

Au Group Electronics Au SAE J1939 Simulator (Gen II) 2.00A User Manual Rev. D

The part # for 6 editions of Au SAE J1939 simulator Gen II 2.00A and required accessories are listed in Table 1-1

Table 1-1Part # for Au SAE J1939 simulator (Gen II) 2.00A and necessary accessories

Au SAE J1939 Simulator (Gen II) 2.00A, Accessories, and Service Part #

Au J1939 Simulator (Gen II 2.00A) Engine Basic Edition SIMJ1939-007

Au J1939 Simulator (Gen II 2.00A) Engine Premium Edition SIMJ1939-008

Non-Plus Edition

Au J1939 Simulator (Gen II 2.00A) Vehicle Platinum Edition SIMJ1939-009

Au J1939 Simulator (Gen II 2.00A) Engine Basic Plus Edition SIMJ1939-010

Au J1939 Simulator (Gen II 2.00A) Engine Premium Plus Edition SIMJ1939-011

Plus Edition

Au J1939 Simulator (Gen II 2.00A) Vehicle Platinum Plus Edition SIMJ1939-012

RS232 Serial Extension Cable CBL-RS232-01

4-wire cable for power supply and CAN network connection CBL-CAN-01

Accessories

USB to RS232 Serial Adapter ADP-USB-232

Service 1 year support and minor upgrades for Au J1939 Simulator SVS-SIM-J1939

1.3. Major Hardware Features

Major hardware features of Au SAE J1939 Simulator (Gen II) 2.00A are listed below:

•SAE J1939-15 Type II ECU: contains an internal 120 ohm load resistor for easy network setup

•Common-Mode Choke and TVS (Transient Voltage Suppressor) protection on CAN bus

•Compact size: 4-1/8" L X 1-3/4"W X 7/8”H

•Enclosure color: Black or PC white

•Operating temperature: -4 ˚F to 185 ˚F (-20 ˚C to 85 ˚C)

•Power supply: +12V~+24V DC, 250mA max

•9 LED indicators: Power, Range, Warning, ▼0%, 20%, 40%, 60%, 80%,▲100%

•1 buzzer

•3 push buttons: The SAE J1939 simulated signal can be adjusted by push buttons: Menu, Down, Up

•1 DB9 Male "BUS" Interface (Figure 1-2):

A four-wire cable (Au Part#: CBL-CAN-01, order separately) can be used for power supply and SAE J1939 network

connection. One end of the cable "CBL-CAN-01" is a DB9 connector which will mate with the “BUS” connector on the

simulator. The other end of the cable consists of pigtail wires which can connect power supply and CAN network. The

color definition of each wire of the cable is illustrated in Table 1-2.

Table 1-2 Color definition of the 4-wire cable (CBL-CAN-01, order separately)

Color Signal

Red +12 V power supply

White CAN-H

Green CAN-L

Black Ground

•1 RS232 interface:

It is used for in field firmware update, license management and computer remote control (Plus editions only). Au J1939

Simulator Plus editions can be connected to the RS232 (serial) port of a PC, either through a RS232 serial extension

cable (Part#: CBL-RS232-01, order separately), as shown in Figure 1-4; or through a USB to RS232 serial Adapter with

USB extension cable (Part #: ADP-USB-232), as shown in figure 1-5. Please refer chapter 4 for detail information on

Remote Terminal Program.

Au Group Electronics Au SAE J1939 Simulator (Gen II) 2.00A User Manual Rev. D

Figure 1-4 Connection of Au J1939 Simulator plus editions to PC with RS232 port

Figure 1-5 Connection of Au J1939 Simulator Gen II plus editions to PC with USB port

1.4. Major Operating Features

•Smart features: Recall last operating mode at power-on, capable of generating dynamic data, etc.

•Ease of use: Easy-to-operate design with production line operator and sales person in mind. No software setup

experience or CAN protocol configuration skill is required. After a network is physically connected, it will

dynamically generate J1939 data when it enters dynamic mode.

•Static mode and dynamic mode:

oStatic mode output static J1939 signal. In this mode, signal can be changed manually

oDynamic mode automatically changes the output value of SAE J1939 signal

oTwo modes can be switched easily

•"Remote Terminal" software available ("Plus" editions only):Display simulated J1939 signal on a computer

screen.

•All push button control functions are available on PC "Remote Terminal" software ("Plus" editions only)

•Easy in-field license upgrade feature with Au License Management Tool. The Basic Edition(s) and Premium

Edition(s) can be easily upgraded to Platinum Edition(s)

•In-field firmware update capability for minor upgrades (SVS-SIM-J1939) and major upgrades (FIRJ1939-00x)

•Annual support and minor upgrade services are available (SVS-SIM-J1939)

•Major firmware upgrade capability available (FIRJ1939-00x)

•Custom design is available upon request

1.5. Basic Functions of Each Edition

Engine Basic Edition(s):

•"Statically" or "dynamically" generate most of the basic engine data

•Push buttons (Up & Down) are used in "static mode" to adjust data outputs

•In "dynamic mode", data cycles automatically in its SAE defined range

•LEDs indicate the control step value and reflect push button operations

Au Group Electronics Au SAE J1939 Simulator (Gen II) 2.00A User Manual Rev. D

•Buzzer sound also reflects push button inputs, and can be enabled/disabled

Engine Premium Edition(s):

•Includes all Engine Basic Edition functions

•Plus water in fuel indicator On/Off control

•Plus Premium features on SAE J1939 Transport Protocols with the following diagnostic messages:

oEngine DM1/DM2 warnings (support single packet and multi-packets)

oEngine “Red Stop” and “Amber” lamp warnings

oEngine DM3

Vehicle Platinum Edition(s):

•Includes all Engine Premium Edition functions

•Plus Vehicle Network features (3 controller applications have been implemented):

oABS related signals

oTransmission related signals

oEngine Configurations

1.6. License /Software Code Upgrade and Support Service

License upgrading and annual service for the 6 editions of SAE J1939 Simulator are summarized in Figure 1-5.

Figure 1-5 License upgrade and service for Au J1939 Simulators (Gen II) 2.00A

•Simulator license can be in-field upgraded to higher editions with a license management toolset: e.g. upgrade

an Au J1939 Simulator from Engine Basic Edition to Engine Premium Edition (LICJ1939-001) or from premium

edition to platinum edition (LICJ1939-002). "Non-Plus" edition is also able to be upgraded to plus editions

(LICJ1939-003).

•Software code (firmware) can be in-field updated with Au PIC Bootloader, for instance, updated firmware code

or custom-made codes can be re-programmed to gain new or special features.

•One year support and minor upgrade service is available (SVS-SIM-J1939).

Au Group Electronics Au SAE J1939 Simulator (Gen II) 2.00A User Manual Rev. D

Chapter 2 Supported SAE J1939 Parameters

2.1. Engine Basic Edition(S)

Au SAE J1939 Simulator Gen II 2.00A Engine Basic Edition(s) support the majority of SAE J1939 engine parameters:

•Engine Speed (RPM) (SPN190)

•Wheel-Based Vehicle Speed (MPH) (SPN 84)

•Engine Oil Pressure(PSI) (SPN 100)

•Engine Coolant Temperature(F) (SPN 110)

•Battery Potential (Voltage), Switched (SPN 158)

•Fuel Level (%) (SPN 96)

•Engine Turbocharger Boost Pressure (PSI) (SPN 102)

•Engine Instant Fuel Economy (SPN 184)

•Engine Fuel Rate (SPN 183)

•Accelerator Pedal Position 1 (SPN 91)

•Engine Intake Manifold 1 Temperature (F) (SPN 105)

•Engine % Load at Current Speed (SPN 92)

•Engine Trip Distance (SPN 244)

•Total Vehicle Distance (SPN 245)

•Engine Total Hours of Operation (Hr) (SPN 247)

•Response for Engine Hour Request

•Engine Clock (HH:MM) (SPN 961, 960)

•Response for Engine Clock Request

•Engine Clock setup (SPN 1605, 1604)

•Cruise Light (SPN 595)

•SAE J1939 Acknowledge protocol (ACK, NACK)

•Engine Address Claimed

•Engine Address CANNOT Claim

•Response for Address Claim Request

•Address Conflict Response with Contention

•Engine DM1 Red Stop Lamp OFF status (SPN 623)

•Engine DM1 Amber Lamp OFF status (SPN 624)

•Engine DM1 (Health-heart-beat) *

•Water-in-Fuel (WIF) Indicator (Health-heart-beat)* (SPN 97)

•Engine Oil Temperature 1 (SPN 175)

•Engine Fuel Temperature (F) (SPN 174)

•Engine Oil Level (%) (SPN 98)

•Engine Coolant Pressure (PSI) (SPN 109)

•Engine Coolant Level (%)(SPN 111)

•Engine IS (Idle Shutdown) has Shutdown Engine (SPN 593)

•Engine IS Driver Alert Mode (SPN 594)

•Engine IS Timer Override (SPN 592)

•Engine IS Timer State (SPN 590)

•Engine IS Timer Function (SPN 591)

•A/C High Pressure Fan Switch (SPN 985)

•Refrigerant Low Pressure Switch (SPN 875)

•Refrigerant High Pressure Switch (SPN 605)

•Engine Wait to Start Lamp (SPN 1081)

•EPS (Engine Protection System)has Shutdown Engine (SPN 1110)

•EPS Approaching shutdown (SPN 1109)

•EPS Timer Override (SPN 1108)

•EPS Timer State (SPN1107)

•EPS Configuration (SPN 1111)

•Engine Alarm Acknowledge (SPN 2815)

Au Group Electronics Au SAE J1939 Simulator (Gen II) 2.00A User Manual Rev. D

•Engine Alarm Output Command Status (SPN 2814)

•Engine Air Shutoff Command Status (SPN 2813)

•Engine Overspeed Test (SPN 2812)

•Engine Air Inlet Pressure (SPN 106)

•Engine Exhaust Gas Temperature (SPN 173)

•Actual Engine - Percent Torque (SPN 513)

•Nominal Friction - Percent Torque (SPN 514)

•Engine Exhaust Gas Recirculation (EGR) Mass Flow Rate (MFR) (SPN 2659)

•Engine Inlet Air Mass Flow Rate (MFR) (SPN 132)

•Vehicle Identification Number (VIN) (SPN 237)

•Response for VIN global request

•Response for VIN specific request

•SAE-J1939 Transport Protocol: TP.CM.BAM, TP.DT

•SAE-J1939 Transport Protocol: TP.CM.RTS, TP.CM.CTS, TP.DT, TP.CM.EndOfMsgACK, TP.Conn.Abort

* Health-heart-beat: normal signal only, no warning. Signal repeats at SAE defined “heart-beat” rate.

2.2. Engine Premium Edition(S)

Au SAE J1939 Simulator Engine Premium Edition(s) support all the SAE J1939 parameters listed with Engine Basic

Edition(s), plus the following SAE J1939 parameters and new features:

•Engine DM1 Warning On/Off control

•Engine DM2 On/Reset control

•Engine Red Stop Lamp On/Off

•Engine Amber Lamp On/Off

•Water In Fuel Indicator On/Off

•Engine DM1 Single-Packet warning

•Engine DM1 Multi-Packet warnings

•Engine DM2 Single-Packet warning

•Engine DM2 Multi-Packet warnings

•Response for DM2 global request

•Response for DM2 specific request

•Engine DM3 and Engine DM2 On/Reset control

•SAE J1939 TP.CM.BAM, TP.DT protocol

•SAE J1939 TP.CM.EndOfMsgAck, TP.CM.RTS, TP.CM.CTS, TP.Conn.Abort, TP.DT protocol

2.3. Vehicle Platinum Edition(S)

Au SAE J1939 Simulator vehicle Platinum Edition(s) support all SAE J1939 parameters listed with Engine Premium

Edition(s), and the following SAE J1939 parameters and new features:

•Engine Configuration

•ABS address claimed

•ABS Address CANNOT Claim

•ABS Response Request for Address Claim

•ABS Address Conflict Response with Contention

•ABS Red Stop Lamp On/Off

•ABS Amber Lamp On/Off

•ABS DM1 (No warning or 1 warning)

•ABS Heart-beat PGN-EBC1

•Transmission Address Conflict Response with Contention

•Transmission address claimed

•Transmission Address CANNOT Claim

•Transmission Response Request for Address Claim

•Transmission Red Stop Lamp On/Off

•Transmission Amber Lamp On/Off

•Transmission DM1 (No warning or 1 warning)

•Transmission Oil Temperature

•Transmission Heart-beat PGN-ETC

Au Group Electronics Au SAE J1939 Simulator (Gen II) 2.00A User Manual Rev. D

Chapter 3 Operating Instructions

All editions of Au SAE J1939 Simulator (Gen II) can be operated by just controlling 3 push buttons. It generates SAE

J1939 signals for product developers, testers, operators and manufacturers.

3.1. Power On

Plug in a 4-wire cable (e.g. Au Part#: CBL-CAN-01) to the Au SAE J1939 Simulator (Gen II) DB9 male connector (on

BUS side). When the CBL-CAN-01 cable is used, connect the Red wire to +12 ~ +24V DC power supply, Black wire to

ground, White wire to CAN-H, Green wire to CAN-L. The Power LED on simulator will light up, and simulator will

resume the last saved operating mode (static mode or dynamic mode).

Note: the 4-wire cable (CBL-CAN-01) is color coded as shown in Table 1-2 (Chapter 1) and is ordered separately.

3.2. Operating Modes (Static/Dynamic)

After power on, Au SAE J1939 Simulator will work in either static mode or dynamic mode.

•Static mode: Au SAE J1939 Simulator (Gen II) generates steady SAE J1939 signals. In this mode, two push

buttons (Up and Down) can be used to change the data outputs. When no button is pushed, all data will stay at

the last value.

•Dynamic mode: The value of all data will change automatically in SAE J1939 defined range.

•Switch between dynamic mode and static mode: press and hold both Menu and Up buttons until a long beep is

heard if buzzer is enabled; or both the "▼0% LED" and the "▲100% LED" flip their status (from on to off or vice

versa)

There are 3 push buttons (Menu, Down, Up) and 9 LEDs (Figure 3-1). Each LED is named after its function.

Figure 3-1 Position of push buttons and LEDs

3.3. Push Button Functions

The push button functions are summarized in Table 3-1.

Table 3-1 Summary of push button functions

Push Button Operation Function

Press Down button Decrease all simulated data until they reach the lowest value

Press Up button Increase all simulated data until they reach the highest value

Press Menu button DM1 Warning On/Off control (N.A. for Engine Basic Edition(s))

Press & hold Menu button when power

Simulator will enter Bootloader mode, if no communication is detected from

a PC Bootloader program within 10 seconds, it’ll resume normal modes

Press & hold both Down + Up button Buzzer ON/OFF control

Press & hold both Menu + Up button Switch between Static/Dynamic mode

Press & hold both Menu + Down button Engine DM2 ON/Reset control (N.A. in Engine Basic Edition)

•Press Menu button:

Au Group Electronics Au SAE J1939 Simulator (Gen II) 2.00A User Manual Rev. D

oMenu button is used to control Warning LED on/off. A single press on Menu button will turn on the Warning

LED if the Warning LED was off, and vice versa.

oThe Menu button function is available only on Engine Premium Edition(s) and Vehicle Platinum Edition(s). In

Engine Basic Edition(s), Menu button is not used, Warning LED is constantly off.

oIf buzzer is enabled, a short beep will be heard upon a press on the Menu button.

In dynamic mode, the simulator automatically adjusts the control step value by itself. This will generate dynamic J1939

signals. In static mode, all* simulated SAE J1939 signal will be controlled by the control step value, which is still able to

be manually controlled by the Up and Down buttons.

Note: * The Engine Clock is not controlled by the control step value and push buttons; it runs all by itself just like a real

clock.

•Press Down button:

oDown button is used to decrease the values of all J1939 signals. A single press will decrease all data one

step from previous values until they reach the minimum values. ▼0% LED will be triggered on or off.

oIf ▼0% LED is on, press Down button one time, ▼0% LED will be off.

oIf ▼0% LED is off, press Down button one time, ▼0% LED will be on.

o80% LED blinks when control step value equals to 80%,

o60% LED blinks when control step value equals to 60%,

o40% LED blinks when control step value equals to 40%,

o20% LED blinks when control step value equals to 20%,

o▼0% LED blinks when control step equals to 0%,

oIf buzzer is enabled, a short beep will be heard upon a press on Down button.

•Press Up button:

oUp button is used to increase the values of all J1939 signals. A single press will increase all simulated data

one step to next data level until they reach the maximum values, ▲100% LED will be triggered on or off.

oIf ▲100% LED is on, press Up button one time, ▲100% LED will be off.

oIf ▲100% LED is off, press Up button one time, ▲100% LED will be on.

o20% LED blinks when control step value equals to 20%,

o40% LED blinks when control step value equals to 40%,

o60% LED blinks when control step value equals to 60%,

o80% LED blinks when control step value equals to 80%,

o▲100% LED blinks when control step value equals to the highest value, 100%.

oIf buzzer is enabled, a short beep will be heard upon a press on Up button.

•Press and hold both Down + Up button for more than 1 second:

oDown + Up buttons are used to turn buzzer on/off.

oIf buzzer is on, press and hold Down + Up for more than 1 second will silent buzzer thereafter.

oIf buzzer is mute, press and hold Down + Up for more than 1 second will enable the buzzer thereafter.

oBoth ▲100% and ▼0% LED will flip their on/off status as a visual indication of this dual-button input.

oIf buzzer is enabled, a long beep will be heard to reflect the input of Down + Up button.

•Press and hold both Menu + Down button for more than 1 second:

oMenu + Down buttons are used to turn Engine DM2 warning on/Reset.

oBoth ▲100% LED and ▼0% LED will flip their status as a visual indication of this dual-button input.

oIf buzzer is enabled, a long beep will be heard to reflect the input of Menu + Down button.

oThe Engine DM2 warning messages (available only at premium editions and platinum editions) are always

on after power-on. It can be reset when an Engine DM3 PGN is received.

oFor continuous test purpose, after an Engine DM3 PGN is received, either re-power-on the simulator or

press and hold both Menu + Down button for more than 1 second will turn on the Engine DM2 warning

again.

Altri manuali per SAE J1939

Indice

Altri manuali AU Interruttore

AU SAE J1939 Manuale utente

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente