Audio Ltd. Envoy En2 Manuale utente
User guide for the En2 PTX plug-on
transmitter
Installing and removing batteries
To open the battery compartment, slide the battery compartment catch away from
the edge. This will unlock it and the batteries can be placed inside with the positive
end outermost (see Fig.1. below).
To close the battery compartment, gently push down the flap until you hear a
clicking sound. The transmitter is now ready to use.
Fig.1
Fig.2.
Switching the transmitter on and off
On/Off Button
Navigation switch
Battery compartment catch
Locking ring
OLED display
To turn the transmitter on, press the On/Off button for one second and the OLED
display and blue ‘On’ led will turn on. To turn the transmitter off, press and hold the
On/Off button for three seconds.
Default screen
Key
1 Battery level icon
2 Menus Locked icon
3 Current gain setting
4 LF Cut active icon
5 RF Output Power icon (Only displayed when ‘Low’ setting selected)
6 48V phantom/Dynamic setting
7 AF level indicator
8 Frequency
9 Frequency selection mode (P = PRESET, U = USER, TUNE = TUNE
mode).
10 Selected channel number (PRESET or USER modes only).
11 Overload indicator.
Enter Main Menu
To access the various transmitter parameters press and hold the navigation switch (see
Fig.2) for 2 seconds to enter the menu. The main menu will be displayed.
Accessing the Frequency option
After accessing the main menu, use the navigation switch to scroll to the Frequency
option. Once the frequency option is highlighted, press down on the navigation switch
to enter the frequency menu to view the range of frequencies.
A range of frequencies will be displayed and the desired one can be highlighted using
the scroll. To confirm the desired frequency press down on the navigation switch to
make the selection. The transmitter will then return to the main menu.
AF Gain option
After accessing the main menu, use the navigation switch to scroll to the AF gain
option. Once the AF gain option is highlighted, press the navigation switch to select
one of 10 AF gain settings.
Use the navigation switch to highlight the desired AF Gain option. To confirm this
choice press navigation switch and the transmitter will save the setting and return to
the main menu.
LF Cut option
After accessing the main menu, use the navigation switch to scroll to the LF Cut
option.
Select the required filter setting.
Options
After accessing the main menu, use the navigation switch to scroll to the Options
menu. When the Options icon is highlighted, press the navigation switch.
On doing so, the Options menu will be displayed as shown below:
Frequency Mode
In selecting the frequency mode the user can select one of three frequency modes,
Factory set Preset, User, or manual Tune.
Preset
In Tune mode the user can select any frequency within the switching bandwidth of
the frequency table in 25kHz steps and then save them to the User memory. The User
memory is initially programmed with a copy of the Preset frequencies until the user
selects and saves a frequency in Tune mode.
Tune
Frequency tables
Units which are programmed with multiple tables will show frequency table selection
on the menu. Entering the frequency table selection screen will show the frequency
table number. The user can select any one of up to 10 tables.
Sub-options menu
RF Power
In selecting the RF Power from the Sub-options menu the user can select High or Low
power settings. In selecting the low power setting the user will extend the battery life
of the transmitter.
Blue LED on/off
Selecting this option allows the user to turn the blue ‘On’ indicator LED, on or off.
The default setting is on.
AF Mute setting
Selecting this option allows the user to configure the On/Off button as a momentary
mute button. This might prove useful in an interview situation where the presenter
wants to keep the transmitter on, but wishes to turn the audio off momentarily.
Note: The On/Off function remains active whilst the button is used as a mute
function, but if the user wants to the turn the transmitter off the button just needs to be
held down for a longer period.
Display settings option
Brightness
The brightness menu selection allows the user to set the brightness of the OLED
display. There are 5 selectable levels available.
Screensaver
The OLED display can be placed into screen saver mode to extend battery life and
also reduce light emission from the transmitter.
There are 4 settings available :–
X - display on all the time
5 - screen enters screen saver after 5 seconds
20- screen enters screen saver after 20 seconds
60 - screen enters screen saver after 60 seconds
Left/Right hand setting
The PTX can be setup to allow right-handed or left-handed operation by the user.
Restore
If for any reason, the user wants to restore the transmitter to the original factory
supplied settings then the user can use the restore function. Please note this will
overwrite any user memory settings and gain settings.
Information option
From the top level menu the Info provides the serial number, Firmware revision and
frequency table information.
After accessing the main menu, use the navigation switch to scroll to the Info option.
Once the Information option is highlighted, press the navigation switch to view the
options.
To view the information for any of these, there is no need to press down the middle
button. Simply scrolling from left to right will enable you to view the data for any of
the three headings. Pressing down on the navigation switch will instantly take the
Altri manuali Audio Ltd. Trasmettitore
