Audix AP62 Manuale utente

PERFORMANCE SERIES WIRELESS

AP61 & AP62 USER GUIDE | SCAN. SYNC. PLAY! TM

TABLE OF CONTENTS

Safety Instructions & Certiﬁcations 2

Introduction 3

Quick Set Up Guide 4

R61 Receiver Front Panel 8

R61 Receiver Back Panel 9

R61 LCD Display 10

H60 Handheld Transmitter 11

B60 Bodypack Transmitter 13

Receiver Operating Instructions / Menu Functions 14

Using the H60 Handheld Transmitter 18

Using the B60 Bodypack Transmitter 20

Performance Tips 22

Rackmounts 23

Rackmount Installation 24

Troubleshooting 26

Group/Channel Charts 27

Speciﬁcations 28

SAFETY INSTRUCTIONS

Please read this instruction manual to ensure proper use and care of your system.

Quick Safety Tips

Unplug the receiver from the wall socket when not in use

Use only with the power supply provided

Keep away from water, moisture, heat generating devices and direct sunlight

Clean only with dry cloth

Do not block the receiver from ventilation

Use only with accessories produced by Audix

Operate and store in a safe temperature range 0°C (32°F) - 43°C (110°F)

CERTIFICATIONS

This product complies with FCC Part 74 regulations and conforms to CE standards.

Documentation available upon request. Operation of wireless devices may require a

license in your area. Please comply with regulations pertaining to your area. Users of

wireless microphones in the USA, on frequencies listed under FCC part 74.801, must

comply with eligibility and licensing requirements under FCC Part 74.834.

INTRODUCTION

Congratulations on the purchase of the Performance Series Wireless system from Audix!

Your system is jam packed with features that will enable you to ﬁne-tune the system as

needed. However, the best part of our design is that the system is simple to use. For most

applications, simply refer to the Quick Set Up Guide to get up and running (pgs 4-7).

Please take a few minutes and read through this manual in order to familiarize yourself

with the system components and the menus. The menus are very intuitive and most

questions about operating the system will be answered by understanding the structure of

the menus.

2. Attach antennas to the back of the receiver. Keep each antenna straight while

screwing it into the connector (2a). After attached, bend antennas into position (2b).

2a 2b

QUICK SET UP GUIDE

Follow these instructions to get up and running in very little time.

1. Install 2 AA batteries in the handheld transmitter and bodypack. Refer to the

diagrams on the equipment to ensure batteries are positioned correctly.

1a 1b

a.) Handheld transmitter: Unscrew bottom portion of the transmitter to expose

battery holder. Push the ﬁrst battery up through the housing with negative side

up. Place the second battery below the ﬁrst with negative side up. The batteries are

spring loaded and will settle into place. Screw the cover back into place.

b.) Bodypack transmitter: With bodypack face down, push the spring release to

the right to open. Place left battery negative side up, and the right battery negative

side down. Snap the battery cover to close.

3. Connect power supply. Loop cable through the metal strain relief as shown above

prior to connecting power supply to receiver. Plug into power outlet.

4. Connect receiver to mixer or ampliﬁer. Make sure audio levels on the mixer are

muted or oﬀ. For guitar, use the 1/4" AF output (line level unbalanced, 4b). For all other

applications use the XLR output (mic level, 4a).

4a 4b

5. Turn on transmitter.

6. Turn on receiver.

7. On receiver, press and hold the UP or DOWN button to trigger Scan for a clear

Group/Channel. After 8-20 seconds a Group/Channel˝ will appear on the receiver.

8. Sync handheld transmitter to

receiver. Unscrew the battery cover and

locate the window housing infrared

device. From a close proximity (6 inches

/ 152.40 mm), point the infrared window

(located on the opposite side of the

batteries) towards the infrared sensor next

to the SYNC button and press the SYNC

button. Within a few seconds the

transmitter Group/Channel and

Frequency will match the receiver.

9. Sync bodypack transmitter to

receiver. Unscrew the battery cover

and locate the window housing infrared

device. From a close proximity

(6 inches / 152.40 mm) point the window

below the LCD screen on the bodypack

towards the infrared sensor next to the

SYNC button and press the SYNC button.

Within a few seconds the transmitter

Group/Channel and Frequency will match

the receiver.

QUICK SET UP GUIDE

Setting up multiple systems utilizes the Scan – Sync functions described to the left. In

general, compatible channels for synchronized use are organized by Group. (See the

Group/Channel chart on page 27.)

Be sure all receivers and transmitters are powered OFF.

1. Power up receiver #1 and matching transmitter: Run the standard Scan and Sync

routine as described in the previous section (Quick Set Up Guide). Leave the system ON.

Move the transmitter at least 6 feet (2 meters) away from the receiver.

2. Power up receiver #2 and matching transmitter: Run the Scan and the receiver

will ﬁnd a clear channel in the same Group as the previous system. Sync the transmitter to

the receiver.

Adding more systems will follow the same procedure as above.

IMPORTANT: Be sure that all transmitters are at least 6 feet (2 meters) from each other as

you set up multiple systems.

Hint: If you are using more than one frequency band, be sure to set up all systems in the

same band before moving to the next.

MULTIPLE SYSTEMS

1 POWER switch. Press for instant ON.

Press and hold for 3 seconds to turn

system OFF.

2 SYNC button. Automatically synchronizes

the transmitter to the receiver.

3 Infrared sensor. Sends data from receiver

to transmitter when SYNC function

is engaged.

4 High contrast LCD display. See Menu

Functions on page 14 for more details.

5 UP button. Only active in Menu mode.

Scrolls forward through menus. Also acts

as hot key for autoscan when pushed

and held.

6 DOWN button. Only active in Menu

mode. Scrolls backwards through

menus. Also acts as hot key for

autoscan when pushed and held.

7 SET button. Press and hold to enter

the Menu mode. Also used to save

settings, exit the Menu mode and tog-

gle between Frequency˝ and Group/

Channel˝ for quick reference.

FRONT PANEL

R62 DUAL RECEIVER

1 2 3 4 5

55 77 44

12 2

3 3

R61 SINGLE RECEIVER

1 BNC connector for Antenna B.

2 Ground lift switch to help eliminate

ground loops or noise from

other sources.

3 Mic level balanced XLR output for

connecting receiver to an audio mixer.

4 Unbalanced ¼ inch output for

connecting receiver to an ampliﬁer.

5 Metal strain relief. Allows power cable

to loop through for added security.

6 DC power jack for external

power supply (12 V).

7 BNC connector for Antenna A.

BACK PANEL

1 7

2 2

3 3

4 4

R62 DUAL RECEIVER

R61 SINGLE RECEIVER

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Audix Sistema microfonico

Audix

Audix Performance AP41 Manuale utente

Audix

Audix SMU1 Manuale utente

Audix

Audix PERFORMANCE Series Manuale utente

Audix

Audix alpha Manuale utente

Audix

Audix MicroPod Series Manuale utente

Audix

Audix AP61 Manuale utente

Audix

Audix RAD-360 Manuale utente

Audix

Audix RAD-360 Manuale utente

Audix

Audix M1255B Series Manuale utente

Manuali Sistema microfonico popolari di altre marche

Paso

Paso R824 Manuale utente

Naxa

Naxa NAM-982 Manuale utente

Motorola

Motorola PMNN4461 Manuale utente

Xvive

Xvive U3 Manuale utente

Tekon

Tekon DUOS Manuale utente

Heyuan Intelligence

Heyuan Intelligence IOT-G2S-01 Manuale utente

Devine

Devine WMD-IE Manuale utente

LG LF-D7150 Manuale utente

GE S768DAV Manuale utente

LD U305 HBH 2 Manuale utente

Chainway

Chainway URA8 Manuale utente

ORATOR

ORATOR D860TD Manuale utente

Sennheiser

Sennheiser Evolution Wireless Digital EW-DX EM 2 Manuale utente

Alpha Technologies

Alpha Technologies RBMS Manuale utente

SWIT Electronics Co.,LTD.

SWIT Electronics Co.,LTD. CW-S150 Manuale utente

Shure

Shure UA844 Manuale utente

Panasonic

Panasonic SHFX70 - DVD HOME THEATER WIRELESS SYSTEM Manuale utente

Pyle

Pyle PDWM5000 Manuale utente