Austlift 141102 Manuale utente
USER MANUAL
RING PANEL LIFTER
141102, 141105, 141110
Lifting Your Business to A Higher Level
1300 100 120
www.austlift.com.au
AUSTRALIAN LIFTING CENTRE PTY LTD
2
ALC UIM Panel Lifter_19
Australian Lifting Centre
USER INSTRUCTION MANUAL RING PANEL LIFTER
141102, 141105, 141110
D
C
B
A
E
L
Ring Panel Lifter
Austlift ring panel lifters are a lifting device which is used together with
Austlift cast plate anchors. Ring lifters are used for lifting large precast
concrete panels. The ring head of the lifter has a locking bolt, which helps
to safely lock into plate anchors while the concrete panels are in the lifting
process. Austlift panel lifters are available in a variety of lifting capacities
to suite your work.
Ring Panel Lifter Specifications
• All ring panel lifters are proof loaded.
• Batch tested, test certificates available with each unit.
Regularly Check Table*
WLL (T)
M max (mm)
N min (mm)
0.7-2.5 13 12
3.0-5.0 19.5 15.5
5.3-10.0 23.5 22.5
WLL
(T)
CODE Wt.
(kg)
DIMENSIONS (mm)
A B C D E L
0.7-2.5 141102 1.6 52 92 70 74 30 285
3.0-5.0 141105 3.5 71 120 86 98 36 285
5.3-10.0 141110 990 156 112 139 50 353
D
C
B
A
E
L
M
N
* Ring lifters should be checked regularly. Follow the regularly check table.
ANCHOR AND LIFTER MUST BE MATCHED
WARNING
Capacities
2.5-10t
Safety Factor
5-1
Certied
AS/NZS
3850
3
ALC UIM Panel Lifter_19
www.austlift.com.au
USER INSTRUCTION MANUAL RING PANEL LIFTER
141102, 141105, 141110
BEFORE USE
You must:
• You must check that the anchor is the same size as the ring panel lifter.
• The length of the lifting slings should be at least twice the distance
between the anchors in order to achieve 60° angles between the sling
legs. A lifting calculation needs to be done if the angle is greater than
60°. It's always better to use a |ifting beam.
• The concrete strength must be greater or at least equal to 15N/mmz2.
• You must check that the locking bolt is leaning on the concrete.
• When tilt up, the locking bolt must not be on the upper position,
You Must not:
• You must not break ’concrete around the anchor. The ring clutch hooks
the anchor without doing anything else, ~ You must not weld neither
the anchor nor the ring clutch whatever the reason you may have,
IN USE
• The ring clutch is used for all load directions. Maximum load of anchor
and clutch must be considered. Angle pull caused by spreaded chain
suspension is limited by a maximal 60°.
• During the transportation, if the anchor point is being used as a tie-
down point, this could shock or impact it caused by snatch or travelling
on rough ground. A pre lifting check of those anchor points is needed,
• When the anchors are used to lift a unit from a mould, the adhesion
between the freshly cast concrete and the mould Increase the load on
the anchors,
MAINTENANCE
• All ring clutches must be inspected at least once a year by an qualified
person. The casting head must not be deformed,
• The ring panel lifter cannot be repaired.
GENERALITY
• The ring panel lifter must be used only for lifting precast concrete units.
• People who use ring panel lifters have to know the usage and safety
instructions.
• All usage and safety instructions must be respected when you lift
elements.
4
ALC UIM Panel Lifter_19
Australian Lifting Centre
USER INSTRUCTION MANUAL RING PANEL LIFTER
141102, 141105, 141110
DEMOULD THE RECESS FORMER
To demould the recess former, insert two rods into
the holes and levered out with a scissor action. This
procedure can avoid damage to the recess former.
Attempting to remove the recess former using the
tip of a carpenter’s hammer will destroy it.
LOCKING THE PANEL LIFTER
The ring panel lifter is positively locked by a simple
hand-operated movement of the locking bolt
resulting in a safe connection of the ring panel lifter
to be able to move in any direction. The precast panel
can now be lifted out of the mould for transporting.
FITTING THE PANEL LIFTER
To transport the concrete panel, an appropriate ring
panel lifter should be inserted over the anchor head
which is in the concrete recess. The load ranges are
designed to mismatch-proof.
RELEASE THE PANEL LIFTER
The ring panel lifter can be released manually by pushing
back the locking bolt once the device is off-load.
USING THE PANEL LIFTER
The ring panel lifter is used for all load directions.
Maximum load of anchor and ring panel lifter must
be considered. Angle pull caused by spreaded chain
suspension is limited by a maximal 60°.
≤60°
≤60°
≤90°
≤90°
≥90°
Wholesale of Lifting, Rigging, Load Restraint
& Height Safety products
Copyright Australian Lifting Centre
Specifications and dimensions subject to change without notice.
1300 100 120
AUSTRALIAN LIFTING CENTRE
www.austlift.com.au
Head Office (NSW)
43 Frank Street
Wetherill Park, NSW 2164
Ph: 02 9757 2277
WA Office
42 Mulgul Road
Malaga, WA 6090
Ph: 08 9248 6674
VIC Office
47 Technology Drive
Sunshine West, VIC 3020
Ph: 03 9314 5525
QLD Office
7 Durbell Street
Acacia Ridge, QLD 4110
Ph: 07 3272 0777
ALC UIM Panel Lifter_19
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Austlift Sistema di sollevamento
Manuali Sistema di sollevamento popolari di altre marche
Genie
Genie Z-60/34 Manuale utente
Screen Technics
Screen Technics INTERFIT Vertical Up Lift Manuale utente
Mortuary Lift
Mortuary Lift ULTIMATE 1000 Manuale utente
Custom Equipment
Custom Equipment Hy-Brid 3 Series Manuale di programmazione
Custom Equipment
Custom Equipment Hy-Brid Lifts 2 Series Manuale di programmazione
Hy-Brid Lifts
Hy-Brid Lifts HB-P3.6 Manuale di programmazione
