Automatic Technology GDO-11 Ero Manuale utente

Sectional Door Opener

Instruction Manual

Doc # 160073_00

Part # 13459

Released 29/08/16

GDO-11 Ero™

GDO-11 Instruction Manual

Table of Contents

1. Installation Safety Warnings! 3

2. Before you Begin 4

Examine the conditions in the garage: 4

Test the following before commencing installation: 4

3. Tools Required 4

4. Kit Contents 5

5. Position 5

6. Fit the Opener 6

7. Bracket Position 6

Wall Bracket Position: 6

Mounting The Wall Bracket: 6

Attach The Rail To The Wall Bracket 6

8. Perforated Angle 7

Attach Perforated Angle or equivalent 7

Alternative Mounting Option 7

9. Mounting Brackets and Arms 8

Mounting The Door Bracket: 8

Attaching the Arms 8

10. Connect to Power 8

11. Setting Limits 9

Setting the Datum: 9

Set the Limit Positions: 9

Resetting the Door Limit Positions 9

Reset all Factory Defaults 9

Setting the PET Mode position 9

12. Safety Testing 10

Test the Close Cycle 10

Testing the Open Cycle 10

Test the Manual Door Operation 10

Adjusting Safety Obstruction Force 10

To Increase Force Pressure 10

To Decrease Force Pressure 10

To Recall Factory Set Force 10

To Recalculate Force Margins 10

13. Control Board & Accessories 11

Control Board Layout 11

Auxiliary Output 11

14. Coding a Transmitter 12

Storing the Transmitter Code 12

Coding a Transmitter to Enable Vacation Mode 12

Coding a Transmitter to enable AUX Output 12

Setting the Transmitter to Operate PET Mode 12

Coding a Transmitter to the Courtesy Light 12

Installation of the Wall Mounted Transmitter 13

Remotely Coding Transmitters 13

Erasing a Stored Transmitter Code 13

Erasing All Transmitter Codes 13

15. Home Owner Safety Warnings! 14

16. Opener Safety & Security 15

Your Door CAN NOT be used when: 15

Your Door CAN be used when: 15

To Disengage the Opener: 15

To Re-Engage the Opener: 15

17. Operating your Opener 15

18. User Operating Controls 16

19. Door Status Indicators 16

20. Specifications 17

21. Troubleshooting 18

22. Maintenance 20

23. Battery Replacement 20

24. Battery Disposal 20

25. Service Schedule 21

26. Warranty 22

27. Optional Accessories 23

Installation Instructions

Home Owner Instructions

GDO-11 Instruction Manual

1. Installation Safety Warnings!

WARNING! • The door may operate unexpectedly, therefore do not allow anything to stay in the path of

the door.

• When operating the manual release while the door is open, the door may fall rapidly due

to weak or broken springs, or due to being improperly balanced.

• The drive must not be used with a door incorporating a wicket door, unless the drive cannot

be operated with the wicket door open.

• The drive is intended to be installed at least 2.5m above the floor.

• Do not disengage the opener to manual operation with children/persons or any objects

including motor vehicles within the doorway.

• If the door is closing and is unable to re-open when obstructed, discontinue use. Do not

use a door with faulty obstruction sensing

• When using auto close mode, a Photo Electric beam must be fitted correctly and tested

for operation at regular intervals. Extreme caution is recommended when using auto close

mode. All safety rules must be followed.

ELECTROCUTION! • Place opener in protected area so that it does not get wet.

• Do not spray with water .

• Disconnect the power cord from mains power before making any repairs or removing covers.

Only experienced service personnel should remove covers from the opener.

• If the power supply cord is damaged, it must be replaced by an Automatic Technology

service agent or suitably qualified person.

• Connect the opener to a properly earthed general purpose 240V mains power outlet

installed by a qualified electrical contractor.

CAUTION:

Emergency Access • If garage has no pedestrian entrance door, an emergency access device should be

installed. This accessory allows manual operation of the garage door from outside in case

of power failure.

Muscular strain • Practice correct lifting techniques (carton weighs approx 9kgs)

• Practice correct lifiting techniques when required to lift the door as per installation instructions.

Fall from ladder • Ensure ladder is the correct type for job.

• Ensure ladder is on flat firm ground that will take the weight without the legs sinking.

• Ensure user has 3 points of contact while on ladder.

Crush injury from unsecured

door

• Place a 2 metre exclusion zone around area under the door while it is unsecured.

• Follow the installation instructions

Garage Door • Examine the door installation, in particular, springs and mountings for signs of wear, damage

and imbalance.

• The garage door must be well balanced. Sticking or binding doors must be repaired by a

qualified garage door installer prior to installation of the opener.

• Remove or disengage all garage door locks and mechanisms prior to installation of the opener.

Entanglement • Never plug in and operate opener prior to installation.

• Keep hands and loose clothing clear of door and guides at all times.

Entrapment under

operating door

• DO NOT operate the opener unless the garage door is in full view and free from objects

such as cars and children/people. Make sure that the door has finished moving before

entering or leaving the garage

• In order for the opener to sense an object obstructing the door way, some force must be

exerted on the object. As a result the object, door and/or person may suffer minor damage

or injury.

• Ensure the garage door is in good working order by undertaking regular servicing.

• Install the optional wall transmitter in a location where the garage door is visible, but out

of the reach of children at a height of at least 1.5m.

• Photo Electric beams must be installed if the closing force at the bottom edge of the door

exceeds 400N (40kg)

This automatic garage door opener is designed and tested to offer safe service provided it is

installed and operated in strict accordance with the following safety warnings. Failure to comply

with the following instructions may result in death, serious personal injury or property damage.

GDO-11 Instruction Manual

3. Tools Required

2. Before you Begin

Test the following before commencing installation:

a. The door MUST BE in good operating condition.

b. Manually move the door up and down, the door should move freely without

binding or sticking.

c. The maximum force required to move the door should not exceed 15kg.

d. Lift the door to about halfway. When released, the door should stay in place.

DIY

DO NOT DO IT YOURSELF:

If any of the above door requirements are not met, DO

NOT attempt to fix yourself. Please contact a garage door

professional. (P) 1300 133 944

Examine the conditions in the garage:

a. Look at the ceiling:

i. Is it plastered? The opener is mounted to a perforated angle which MUST be securely fastened to a structural support.

You will need to locate the structural beams in the ceiling which are generally 400mm apart.

ii. does it have exposed beams? The opener is mounted to a perforated angle which must be securely fastened to a

structural support like the exposed beams. You may need to install a 40mm thick board (not supplied) between structural

supports.

b. Look at the wall above the garage door.

i. Is it brick? The wall bracket MUST be securely fastened to the wall with suitable screws and ensure it does not move.

Screwdrivers

Adjustable End Wrench

Sockets and Wrench

Pencil

Drill

2 x Screws

(M6 x 20mm)

Stepladder

Perforated Angle

Metal pieces

(32 x 32 x 1.5mm) x 1200mm length

4 x Screws

(M8 x 20mm)

4 x Bolts and Nuts

(M8)

Drill Bits

Pliers

Hack saw

Tape Measure

Level

ii. Is it timber? The wall bracket MUST be securely fastened to a structural

support. You may need to install a 40mm thick board (not supplied) between

structural supports to fasten the wall bracket to.

GDO-11 Instruction Manual

4. Kit Contents

1. 1 x GDO-11 drive unit

2. 2 x Transmitters and batteries

3. 1 x Bent arm door attachment

4. 1 x Straight arm door attachment

5. 1 x Wall bracket TS01

6. 1 x Door bracket Locator

7. 1 x Door bracket

8. 3 x Pin Snap SSP 8 ZNU 31080

9. 2 x Hex Head screw M8x25

10. 1 x Pin 0890

11. 2 x Clevis Pin 0829

12. 2 x Hex Serration flange nut M8

13. 4 x Hex flange screw taptite ‘S’ M4 x 10

14. 1 x Visoclip

PLUS

15. 2 x Track Bracket

16. 1 x Pre-Assembled

Single Piece C-Rail

10.00°

min

DOORS HIGHEST

POINT

MINIMUM HEAD

ROOM FOR STEEL

RAIL 57mm

10 8

5. Position

Perforated

Angle

The Opener:

a. MUST BE installed in a dry position, protected from weather.

b. REQUIRES properly earthed 3 pin single phase power on the ceiling within an arms length of the opener.

c. Requires a MINIMUM HEADROOM of 57mm between the highest point of the door’s travel and the ceiling.

d. Use the diagram below as a reference when completing the installation.

118

GDO-11 Instruction Manual

6. Fit the Opener

Secure C-Rail to Opener:

a. Remove the Opener from the box and place onto towel.

b. Locate and insert the shaft of drive unit 1into the C-Rail’s sprocket.

c. Fix the two track brackets 15 with four (4) M4 x 8 screws 14 supplied in accessory pack.

d. Place drive unit back in packing box for protection.

Locate shaft into

the sprocket

14 WARNING! DO NOT

use tek screws to affix

rail. Only use the screws

provided, and fix these

into the pre-punched

and threaded holes in

the chassis.

7. Bracket Position

Wall Bracket Position:

a. Determine the centre of the door and mark this point with a line on the wall

above.

b. Raise the door and find the highest point of travel of the first (top) door panel.

60mm

Level

WARNING! The Opener must be securely fastened to structural

supports, otherwise opener failure may ensue causing serious

personal injury and / or property damage.

DO NOT DO IT YOURSELF: If sufficient structural support can not

be found, contact a door profressional for installation.

DIY

c. Using step ladder and a level, transfer this height to the wall above the door

and mark a line 60mm above it, across the centre line.

Mounting The Wall Bracket:

a. Draw two lines extending 21.5mm from each side of the centre point.

b. Centre the wall bracket 6over the intersection of these two lines. Mark

centres for at least two holes and ensure it is into a solid mounting point.

c. Drill holes in the wall with an appropriate bit.

d. Secure to the wall using:

i. IF CONCRETE OR BRICK:

8mm (5/6”) loxins/dynabolts.

ii. IF TIMBER:

wood screw #20 or similar (min. 50mm).

Attach The Rail To The Wall Bracket

a. Leave the drive unit in its packing box on the floor for protection and lift the

other end of the C-Rail.

b. Attach the C-Rail assembly 16 to the wall bracket 5with the

90mm long pin 10 and secure with the supplied pin snap 8.

GDO-11 Instruction Manual

8. Perforated Angle

Attach Perforated Angle (not supplied) or equivalent

a. Measure across the ceiling from the centre point 3177mm (+/- 150mm) to find a supporting beam.

b. Create a perforated angle which best suits your site. Use a hack saw to cut the L shape metal strips. Secure the perforated

angle to a supporting beam using diagrams shown below.

c. Raise the drive unit to the ceiling mounted perforated angle and secure with M8x20mm screws and nuts (not supplied). Strips

should not extend more than 18mm below centre of drive unit mounting holes.

d. To prevent moisture on the C-rail running into the powerhead it is recommended a strip of silicon sealant is placed across the

top of the C-rail just before the opener.

Ceiling Beams that run towards the door requires:

1 x perforated L shape metal strip and

2 x shorter perforate L shape metal drop down strips..

Ceiling Beams that run parallel to the door requires:

2 x perforated L shape metal strips and

2 x shorter perforate L shape metal drop down strips..

(Not supplied)

Drill hole at centre of

track (recommended

bolt size M6 or M8)

Ceiling

Aluminium rail

Shuttle VP2 assembly

Alternative Mounting Option

(for One piece door without track (Tilt Door / J-Type))

The opener can be fastened to the roof by driving a bolt

through the C-Rail into a structural timber support. The bolt

head’s height must not exceed 6mm.

GDO-11 Instruction Manual

9. Mounting Brackets and Arms

Mounting The Door Bracket:

a. The door bracket locator 6is placed over the door bracket

7, on the door’s centre line one-third down the top panel and

mounted using M6 or equivalent screws (not supplied),

b. STEEL DOORS ONLY: Bracket can be welded in place.

NOTE: If in doubt about the door’s strength, reinforcement

may be added to the door’s frame where necessary. Door

damage may occur if the bracket is installed on a panel

with insufficient strength. The opener’s warranty does not

cover damage caused to the door and/or door panels.

Attaching the Arms

a. Assemble the bent arm 3(connecting to the door) to the

right side of the straight arm 4with bolts 9and nuts 12

supplied in the accessory pack. Connect the straight arm 4to

10. Connect to Power

Initial Preparation:

a. Swing open the controls cover to gain the access to the controls panel and

swing back into it position when setup is completed.

b. Engage the C-Rail’s trolley (attached to the door via the arms) with the

chain index by moving the door.

c. If the trolley does not “click” firmly onto the chain index, ensure that

the manual release cord is not in the disengaged position by pulling it

backwards.

NOTE: This cover has a label that says “Do not remove” however, this only

applies during normal operation. This cover must be removed to setup the

opener. Remove the button cover with a blade screwdriver.

d. Switch power on to the opener. The red CLOSE LIMIT LED will be flashing.

e. Press and hold the MINUS (-) button - the door should start closing. If door

starts to close, release button.

NOTE: If the door opens, release the MINUS (-) button and press the OPERATE

button once to change the motor’s direction.

the shuttle with a clevis pin 11 and a pin snap 8. Always use both bent and straight arms.

b. Connect the assembled arm to the bracket with clevis pin 11 and pin snap 8. The angle “A” must be more than 10°.

GDO-11 Instruction Manual

11. Setting Limits

Set the Limit Positions:

The Limit Positions can vary due to site conditions, such as uneven

ground. When setting the Close limits, ensure the position is when

the door makes first contact with the ground. Alternatively for the

Open limits the position should be at the height of the garage

opening.

WARNING! In setting the close limit position, do not

force the door into the floor with excessive force, as

this can interfere with the ease of operation of the

manual release mechanism.

a. Press and hold MINUS (-) button until the door reaches your

desired close limit position. The rubber strip at the bottom of the

door should form a good seal with the ground.

b. Release the MINUS (-) button when the door is near the desired

closed position. Single presses of the MINUS (-) button will inch

the door closer to the ground.

c. If the door overshoots press the PLUS (+) button to move the

door in the open direction.

d. When the door is at the desired close position, press the LIMIT

SET button, the OPEN LIMIT LED will now flash.

e. Press and hold the PLUS (+) button until the door reaches your

desired open limit position. Single presses of the PLUS (+) button

will inch the door open.

f. If the door overshoots press the MINUS (-) button to move the

door in the close direction.

g. When the door is at the desired open position, press the LIMIT

SET button.

WARNING! The door will automatically close, open and

close again after the next step. Ensure that nothing is

in the door’s path.

h. The door will now automatically close and open to calculate the

safety obstruction settings.

Resetting the Door Limit Positions

Limit positions can be deleted by:

a. Press and hold MINUS (-) button for six (6) seconds until the

CLOSE LIMIT LED flashes quickly.

b. Release the MINUS (-) button.

NOTE: If no action is taken within 30 seconds, the opener will return

to normal operating mode and restore the original settings.

c. Follow steps a - f in Set the Limits Poisitions to set new limit

positions.

Reset all Factory Defaults

a. Turn power to the opener off.

b. Press and hold the SET Button.

c. Turn power on while holding the SET button.

Continue to hold until all LED’s are off.

d. This will not erase transmitter codes stored in

memory.

Setting the PET Mode position

When activated, PET mode drives the door to a preset

position from the close position, therefore allowing a

pet or parcel to go under the door.

a. Drive and stop the door at the deisred PET mode

open position by pressing the transmitter button

coded for Open/Stop/Close operation.

b. Press and hold the PLUS (+) button on the opener

for six (6) seconds until the OPEN and CLOSE LED’s

are lit to record the new PET position.

c. Release the PLUS (+) button.

Setting the Datum:

a. Press and hold the MINUS (-) or PLUS (+) buttons to move the door to the

halfway position. Ensure that the door, shuttle and chain index are engaged.

b. Using a small blade screw driver turn the datum adjust screw slowly until the

yellow status LED just illuminates.

NOTE: If the status LED is already illuminated when power is connected then

turn the datum adjust screw until the LED goes off then turn back one notch to

illuminate again.

AUX

OSC

EB2

EB1

V+

WARNING! The safety obstruction detection system

is inoperable while MINUS (-) and PLUS (+) drive

buttons are being used and travels limits are not set.

GDO-11 Instruction Manual

12. Safety Testing

Test the Close Cycle

a. Press the OPERATE button to open the door.

b. If the door closes, press the OPERATE button to stop the door,

then press OPERATE again to open.

c. Place a piece of timber approximately 40mm high (or the openers

cardboard box) on the floor directly under the door.

d. Press the OPERATE button to close door.

e. The door should strike the object and re-open.

f. Remove the timber or cardboard box.

Testing the Open Cycle

a. Press the OPERATE button to close the door.

b. Press OPERATE again to open the door.

c. When the door reaches approximately half way, firmly grab the

door’s bottom rail - the door should stop.

If the door does not reverse readily when closing, or stop when

opening, put the door into manual by pulling down on the manual

release string to diesengage the motor and contact 1300 133 924

for support.

Test the Manual Door Operation

Periodically disengage the opener and manually operate the door.

The door must be smooth to operate by hand. The force required on

the bottom rail should not exceed 15 kg.

CAUTION: Take care when completing a

safety test. Failure to follow this warning

can result in serious personal injury and/or

property damage.

WARNING! If the door is closing and is unable

to re-open when obstructed, discontinue use.

Do not use a door with faulty obstruction sensing.

Wood 40mm

high or opener

cardboard box

To Recall Factory Set Force

a. Holding down the FORCE MARGIN SET button

and the LIMIT SET button for two seconds.

b. Release both buttons. The default setting should

now be recalled.

To Recalculate Force Margins

a. Press and hold the FORCE MARGIN SET Button for

six (6) seconds, the beeper will sound once.

b. The door will start to move and re-calculate force

margins. The door can move between the open and

close limit positions up to four (4) times (depending

on the position of the door and the power up

condition).

c. A single beep will be heard once the process is

complete.

d. Test the force again as per Testing Close Cycle and

Testing Open Cycle.

Adjusting Safety Obstruction Force

The Safety Obstruction Force is calculated automatically during

setup. Adjusting this is normally only necessitated by environmental

conditions such as windy or dusty areas, and areas with extreme

temperature changes.

To Increase Force Pressure

a. Hold down the FORCE MARGIN SET button.

b. While holding the FORCE MARGIN SET button, press the PLUS

(+) button. Each press will increases the force margin.

c. The OPEN LIMIT LED will flash each time the PLUS (+) button is

pressed to indicate an increase in force.

d. If the OPEN LIMIT LED flashes continuously when the PLUS (+)

button is being pressed, this indicates that the maximum force

setting has been reached.

e. Test the force again as per Testing Close Cycle and Testing Open

Cycle.

To Decrease Force Pressure

a. Hold down the FORCE MARGIN SET button.

b. While holding the FORCE MARGIN SET button, press the MINUS

(-) button. Each press will decrease the force margin.

c. The CLOSE LIMIT LED will flash each time the MINUS (-) button is

pressed to indicate a decrease in force.

d. If the CLOSE LIMIT LED flashes continuously when the MINUS

(-) button is being pressed, this indicates that the minimum force

setting has been reached.

e. Test the force again as per Testing Close Cycle and Testing Open

Cycle.

WARNING! If the door fails these tests,

put the opener into manual mode, only

operate the door by hand and call for

service.

Altri manuali per GDO-11 Ero

Indice

Altri manuali Automatic Technology Apriporta da garage

Automatic Technology

Automatic Technology GDO-9v2 Enduro Gen 2 Manuale utente

Automatic Technology

Automatic Technology GDO-9v2 Enduro Gen 2 Manuale utente

Automatic Technology

Automatic Technology GDO-9 Dynamo Gen 2 Manuale utente

Automatic Technology

Automatic Technology GDO-9V1 SecuraLift Manuale utente

Automatic Technology

Automatic Technology Axess Pro Series Manuale utente

Automatic Technology

Automatic Technology AM-808 Manuale utente

Automatic Technology

Automatic Technology GDO-6 v2 Manuale utente

Automatic Technology

Automatic Technology GDO-10v1Toro Manuale utente

Automatic Technology

Automatic Technology HiRO GDO-12 Manuale utente

Automatic Technology

Automatic Technology SecuraLift Rhino Manuale utente

Automatic Technology

Automatic Technology GDO-2 SecuraLift Manuale utente

Automatic Technology

Automatic Technology Dominator AM800 Manuale utente

Automatic Technology

Automatic Technology GDO-6v4 EasyRoller Manuale utente

Automatic Technology

Automatic Technology GDO-8 Shed Master Manuale utente

Automatic Technology

Automatic Technology Hiro GDO-12V1 Manuale utente

Automatic Technology

Automatic Technology iOpener RD40 Manuale utente

Automatic Technology

Automatic Technology GDO-6 EasyRoller Manuale utente

Automatic Technology

Automatic Technology SecuraLift GDO-9v3 Manuale utente

Automatic Technology

Automatic Technology GDO-9 Dynamo Gen 2 Manuale utente

Automatic Technology

Automatic Technology GDO-4 EasyRoller Manuale utente

Automatic Technology

Automatic Technology Axess Pro Series 1101 Manuale utente

Automatic Technology

Automatic Technology GDO-2 SecuraLife Manuale utente

Automatic Technology

Automatic Technology GDO-8v1 EasyRoller II Manuale utente

Automatic Technology

Automatic Technology Smart Phone Control Manuale utente

Manuali Apriporta da garage popolari di altre marche

Dorma

Dorma ES 90 Manuale utente

Garaga

Garaga SECURITY+ 3265GCM 1HP Manuale utente

Chamberlain

Chamberlain Whisper Drive SECURITY+ WD822K Series Manuale utente

Chase Doors

Chase Doors DuraShield Manuale utente

CSI

CSI Classic Manuale utente

HATO

HATO 120 Manuale utente

Chamberlain

Chamberlain Elite 3575S Manuale utente

Richmond

Richmond GTR156 Manuale utente

Raynor

Raynor 1280RGD Manuale utente

CAME

CAME F4000 Series Manuale utente

B&D

B&D Controll-A-Door 5 Manuale utente

BFT

BFT PRV AA SL Manuale utente

Craftsman

Craftsman 139.53924 Manuale utente

Chamberlain

Chamberlain MyQ 940ESTD Manuale utente

Westfalia

Westfalia 19 36 07 Manuale utente

Chamberlain

Chamberlain HD520EVP Manuale utente

Cardin

Cardin BL Series Manuale utente

Chamberlain

Chamberlain 8355 - 1/2 hp Manuale utente