Automatic Technology Smart Phone Control Manuale utente

Wireless Smart Hub Installation Instructions

Smart Phone Control Kit

TRANSCEIVER KIT NTR-1V1 - ORDER NO. 14825

ITEM DESCRIPTION QTY

1NETWORK TRANSCEIVER NTR-1V1 AY 1

2 TIMING HARNESS 400MM VR12 AY 1

3 TAPTITE SCREW “P” M4 X 12 2

4 VELCRO 20 X 50 1

Garage Door Openers

Doc # 160064_04

Part # 13453

Released 28/11/18

This device allows for unattended operation of the door when not in line-of-sight of the door

opener.

The door may operate unexpectedly, therefore do not allow anything to stay in or near the path of the door.

When the door is not operating automatically, watch the door when it is moving and keep people away until

the door is completely opened or closed. Contact with the moving door can cause serious personal injury

or damage to property.

Your opener must be fitted with SAFETY BEAMS. Safety Beams detect any obstructions in the door’s

path and override automatic operation if one presents. These must be installed as in accordance

with UL 325 and CSA C222.2 No 247.

This is in addition to regular professional servicing, and monthly obstruction tests as detailed in your

opener’s Home Owners Manual.

CLASS B DEVICE CAN ICES-3 (B)/NMB-3 (B)

This equiment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and

on, the user is encourage to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or experienced radio/TV technician for help.

Changes or modifications not expressly

approved by the party responsible

for compliance could void the user’s

authority to operate the equipment.

To comply with FCC/IC RF exposure limits for general population / uncontrolled exposure, the antenna(s) used for this transmitter must be installed

to provide a separation distance of at least 7.87in (20cm) from all persons and must not be co-located or operating in conjunction with any other

antenna or transmitter.

The compliance to FCC radiation exposure limits for an uncontrolled environment, and a minimum

of 20cm separation between antenna and body.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

Mounting the Hub

a. Determine whether you are going to wall mount the hub.

ii.If hub is to be placed on bench, simply connect to power

supply, turn on and proceed to installing the Transceiver.

iii. If hub is to be wall mounted follow steps below.

d. To wall mount - Use wall bracket 3as template to mark

where to drill holes. Pre-drill holes.

i. For plaster walls - insert (2) two Plastic wall plugs into holes,

place wall bracket over holes and affix with (2) two self

tapping screws 5.

ii.For brick walls - place wall bracket 3over holes and affix

with (2) two self tapping screws 5.

c. Slide the hub 1over the bracket.

d. Connect the power supply and turn on.

This device must be connected to power at all

times. DO NOT disconnect power after setup.

Before going out to site, check the following with the customer:

a. The customer has a Smart Phone: Android (running 4.4 and above) or IPhone (running iOS8 and above)

b. An internet connection for remote operation is available.

c. A 2.4ghz WiFi network is set up.

d. We recommend the customer has a WPA2 encryption on the WiFi network as other network types are not as secure.

Installation

Important Safety Instructions

WARNING! • DO NOT attempt to disassemble, repair or modify the product. This will invalidate the

warranty.

• Do not allow children to play with the Base Station or your smart phone if the ATA phone

app has been installed.

ELECTROCUTION! • Keep the device away from water and other liquids. In the event that water or other liquids

enter the device, power off he product immediately and clean the device.

• To reduce the risk of fire or electric shock, do not expose this device to rain or moisture. The

device should not be exposed to dripping or splashing.

• DO NOT remove the cover as there are no user-serviceable parts inside.

CAUTION:

Fall from ladder • Ensure ladder is the correct type for job.

• Ensure ladder is on flat ground.

• Ensure user has 3 points of contact while on ladder.

Roller Door Opener Set Up

Preparation of Opener

a. Disconnect the power supply to the opener.

b. Remove the light diffuser via screw at the bottom.

c. Remove the grommet out of the back cover.

d. Cut (1) one side of the grommet with a knife or scissors.

e. Slide the network timing harness 2into the cut in the

grommet.

f. Refit grommet to back cover by sliding the harness

through hole before fitting grommet.

g. Connect the harness to the network pin on the control

board.

h. Refit the light diffuser.

Mount and connect Transceiver

a. Plug the other end of the harness into the transceiver 1.

b. Place the transceiver 1on the side of the opener to

the black, back cover so that the screw holes on the

transceiver line up with those on the back cover.

c. Secure transceiver using the (2) two Taptite M4 x 12

screws 3or velcro 4.

Re-setup and Test the Opener

a. Reconnect power and remove the button cover.

b. Setting Limits:

i. If limits have not been set, follow the openers

installation sheet to set limits.

ii.If limits were set previously, clear limits and follow

openers installation sheet to set limits.

c. Refer to the Smart Phone Control Kit User Guide to set up

network capabilities.

Network Pin

Light diffuser

Grommet

Light diffuser

screw

Aerial slot

Affix with screw here

Preparation of Opener

a. Disconnect the power supply to the opener.

b. Open the side cover on the right hand side (looking from

back of unit).

c. Connect the harness 2to the network / programmer pin on

the control board.

d. Place the transceiver 1inside the cover, threading the aerial

through the slot provided and affix with one (1) Taptite Screw

e. Refit the side cover.

Re-setup and Test the Opener

a. Reconnect power and remove the button cover.

b. Setting Limits:

i. If limits have not been set, follow the openers installation

sheet to set limits.

ii.If limits were set previously, clear limits and follow operators

installation manual to set limits.

c. Refer to the Smart Phone Control Kit Quick Set Up Guide to

set up network capabilities.

NOT available with AM-800

(optional for AM-808)

Sectional Door Opener Set Up

Automatic Technology America

VIneyard Centre II, 1452 Hughes Road, Grapevine, Texas 76051, United States of America

P: +1 817 873 5076 W: www.automatictechnology.com

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and

Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.

2. This device must accept any interference, including interference that may cause undesired operation of the

device.

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation,

Sciences et Développement économique Canada applicables aux appareils radio exempts de licence.

L’exploitation est autorisée aux deux conditions suivantes :

1. L’appareil ne doit pas produire de brouillage;

2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en

compromettre le fonctionnement.

Warranty

WARRANTY PERIOD

ACCESSORIES 1 Year

This Warranty is to be read in conjuction with the owner’s copy of the operator installation instruction

Indice

Altri manuali Automatic Technology Apriporta da garage

Automatic Technology

Automatic Technology SecuraLift GDO-9v3 Manuale utente

Automatic Technology

Automatic Technology GDO-10v1 Toro Manuale utente

Automatic Technology

Automatic Technology GDO-10V3L2 Toro Manuale utente

Automatic Technology

Automatic Technology AM-808 Manuale utente

Automatic Technology

Automatic Technology Hiro GDO-12V1 Manuale utente

Automatic Technology

Automatic Technology SecuraLift GDO-7V1 Guida rapida

Automatic Technology

Automatic Technology Axess Pro Series 1101 Guida rapida

Automatic Technology

Automatic Technology GDO-11V3 Ero Manuale utente

Automatic Technology

Automatic Technology 62717 Manuale utente

Automatic Technology

Automatic Technology GDO-6 EasyRoller Manuale utente

Automatic Technology

Automatic Technology GDO-9V1 SecuraLift Manuale utente

Automatic Technology

Automatic Technology PA1000V1 Manuale utente

Automatic Technology

Automatic Technology GDO-6 v2 Manuale utente

Automatic Technology

Automatic Technology Axess Pro Series Manuale utente

Automatic Technology

Automatic Technology GDO-4 EasyRoller Manuale utente

Automatic Technology

Automatic Technology GDO-6 EasyRoller Manuale utente

Automatic Technology

Automatic Technology Ero GDO-11v2 Manuale utente

Automatic Technology

Automatic Technology Toro GDO-10v2 Manuale utente

Automatic Technology

Automatic Technology NeoSlider TrioCode 128 NES-500 Manuale utente

Automatic Technology

Automatic Technology SecuraLift Trio Manuale utente

Automatic Technology

Automatic Technology Toro GDO-10V2L2 Manuale utente

Automatic Technology

Automatic Technology GDO-8 ShedMaster Guida utente

Automatic Technology

Automatic Technology GDO-2 SecuraLift Manuale utente

Automatic Technology

Automatic Technology GDO-11 Ero Manuale utente

Manuali Apriporta da garage popolari di altre marche

Dorma

Dorma ES 90 Manuale utente

Garaga

Garaga SECURITY+ 3265GCM 1HP Manuale utente

Chamberlain

Chamberlain Whisper Drive SECURITY+ WD822K Series Manuale utente

Chase Doors

Chase Doors DuraShield Manuale utente

CSI

CSI Classic Manuale utente

HATO

HATO 120 Manuale utente

Chamberlain

Chamberlain Elite 3575S Manuale utente

Richmond

Richmond GTR156 Manuale utente

Raynor

Raynor 1280RGD Manuale utente

CAME

CAME F4000 Series Manuale utente

B&D

B&D Controll-A-Door 5 Manuale utente

BFT

BFT PRV AA SL Manuale utente

Craftsman

Craftsman 139.53924 Manuale utente

Chamberlain

Chamberlain MyQ 940ESTD Manuale utente

Westfalia

Westfalia 19 36 07 Manuale utente

Chamberlain

Chamberlain HD520EVP Manuale utente

Cardin

Cardin BL Series Manuale utente

Chamberlain

Chamberlain 8355 - 1/2 hp Manuale utente