AutomationDirect PRODUCTIVITY 2000 Manuale utente

Sales 800-633-0405 www.productivity2000.com

1 OVER

2J 0526

3E 1000

4 UNDER

5 OVER

6 21.35

7 1.245

8 SPARE

2000

P2-08THM Analog Input

The P2-08THM Thermocouple Input Module

provides eight differential channels for receiving

thermocouple and voltage input signals for use

with the Productivity2000 System.

General Specifications ...................... 1

T/C Input Specifications ..................... 2

Voltage Input Specifications .................. 2

Configuration/Diagnostics .................... 2

Wiring Diagram and Schematic................ 3

Module Installation Procedure................. 4

QR Code ................................. 4

Hot Swap Information ....................... 4

Wiring Options............................. 5

Module Configuration ....................... 5

Typical Application Example .................. 6

OLED Panel Display Menus .................. 7

Warning .................................. 8

Removable Terminal Block Specifications. . . . . . . . 8

General Specifications

Operating Temperature 0º to 60ºC (32º to 140ºF)

Storage Temperature -20º to 70ºC (-4º to 158ºF)

Humidity 5 to 95% (non-condensing)

Environmental Air No corrosive gases permitted

Vibration IEC60068-2-6 (Test Fc)

Shock IEC60068-2-27 (Test Ea)

Field to Logic Side Isolation 1800VAC applied for 1 second

Heat Dissipation 500mW

Enclosure Type Open Equipment

Agency Approvals UL508 File E139594, Canada & USA

CE (EN61131-2*)

Module Keying to Backplane Electronic

Module Location Any I/O slot in a Productivity2000 System

Field Wiring

Removable terminal block (included).

The P2-08THM module is not compatible with the

ZIPLink wiring system.

EU Directive

See the “EU Directive” topic in the Productivity2000

Help File. Information can also be obtained at:

www.productivity2000.com

Connector Type (included) 18-position removable terminal block

Weight 90g (3.2 oz)

*Meets EMC and Safety requirements. See the D.O.C. for details.

Terminal Block Included. Not Compatible with ZIPLink.

Warranty: Thirty-day money-back guarantee. Two-year limited

replacement. (See www.productivity2000.com for details).

2Tech Support 770-844-4200www.productivity2000.com

T/C Input Specifications

Input Channels 8 Differential

Data Format Floating Point

Common Mode Range ±1.25 V

Common Mode Rejection 100dB @ DC and 130dB @ 60Hz

Input Impedance >5MΩ

Maximum Ratings Fault protected inputs to ±50V

Resolution 16-bit, ±0.1°C or °F

Thermocouple Input Ranges

Type J -190° to 760°C (-310° to 1400°F);

Type E -210° to 1000°C (-346° to 1832°F);

Type K -150° to 1372°C (-238° to 2502°F);

Type R 65° to 1768°C (149° to 3214°F);

Type S 65° to 1768°C (149° to 3214°F);

Type T -230° to 400°C (-382° to 752°F);

Type B 529° to 1820°C (984° to 3308°F);

Type N -70° to 1300°C (-94° to 2372°F);

Type C 65° to 2320°C (149° to 4208°F);

Cold Junction Compensation Automatic

Thermocouple Linearization Automatic

Accuracy vs. Temperature ±50ppm per °C (maximum)

Linearity Error ±1°C maximum (±0.5°C typical)

Monotonic with no missing codes

Maximum Inaccuracy ±3°C maximum (excluding thermocouple error)

(including temperature drift)

Warm-up Time 30 minutes for ±1% repeatability

2 minutes to reach voltage specifications

Sample Duration Time 270ms

All Channel Update Rate 2.16 s

Open Circuit Detection Time Within 2s

Conversion Method Sigma-Delta

External DC Power Required None

Voltage Input Specifications

Linear mV Device Input Ranges

0-39.0625 mVDC,

+/-39.0625 mVDC,

+/-78.125 mVDC,

0-156.25 mVDC,

+/-156.25 mVDC,

0-1250 mVDC

Max Voltage Input Offset Error 0.05% @ 0°- 60°C, typical 0.04% @ 25°C

Max Voltage Input Gain Error 0.06% @ 25°C

Max Voltage Input Linearity Error 0.05% @ 0°- 60°C, typical 0.03% @ 25°C

Max Voltage Input Impedance 0.2% @ 0° - 60°C, typical 0.06% @ 25°C

Configuration/Diagnostics

Burn-out Detection: High Side/Disable 1 bit per module

°C/°F (T/C Only) 1 bit per module

Module Diagnostics Failure 1 bit per module

Burn-out (on if T/C input is open – no connection

between TCn+ and TCn-) 1 bit per channel

Channel Under-range (T/C only) 1 bit per channel

Channel Over-range (T/C only) 1 bit per channel

Sales 800-633-0405 www.productivity2000.com

AC or DC

Thermocouple Input CircuitsVoltage Input Circuits

Excitation

Power Supply

Transmitter

Power Supply

Ungrounded/Shielded

Thermocouple TC+

TC-

TC+

TC-

TC+

TC-

Grounded/Shielded

Thermocouple

Infrared

Thermocouple

4-wire

Voltage

Transmitter

Load Cell

Strain Gauge

Voltage Divider

TC+

TC-

TC+

TC-

TC+

TC- TC1+

TC1-

TC2+

TC2-

TC3+

TC4+

TC3-

TC4-

TC5+

TC8+

TC8-

CH1 T/C

INPUT

INTERNAL

MODULE CIRCUITRY

TC5-

TC6+

TC6-

TC7+

TC7-

CH2 T/C

INPUT

CH3 T/C

INPUT

CH4 T/C

INPUT

CH5 T/C

INPUT

CH6 T/C

INPUT

CH7 T/C

INPUT

CH8 T/C

INPUT

12345678910 11 12 1813 14 15 16 17

Wiring Diagram Schematic

NOTES:

1. Connect shield to thermocouple signal/ground only. Do not connect to

both ends.

2. Install jumper wire on each unused input,

TC+ to TC-.

3. With grounded thermocouples, take precautions to prevent having a

voltage potential between thermocouple tips. A voltage of 1.25V or

greater between tips will skew measurements.

4. Use shielded, twisted thermocouple extension wire that matches the

thermocouple type. Use thermocouple-compatible junction blocks.

TC+

TC-

4Tech Support 770-844-4200www.productivity2000.com

Module Installation QR Code

Use any QR Code reader application to

display the module’s product insert.

Important Hot-Swap Information

The Productivity2000 System supports hot-swap!

Individual modules can be taken offline, removed, and

replaced while the rest of the system continues con-

trolling your process. Before attempting to use the hot-

swap feature, be sure to read the hot-swap topic in the

programming software’s help file or our online documen-

tation at AutomationDirect.com for details on how to plan

your installation for use of this powerful feature.

1 Align

with slot

2rotate

to seated

position

WARNING: Do not apply field power until

the following steps are completed. See

hot-swapping procedure for

exceptions.

WIRE STRIP

LENGTH

WIRE STRIP

LENGTH

Step One: Align module

catch with base slot and

rotate module into

connector.

Locked Unlocked

Step Two: Pull top locking tab

toward module face. Click indi-

cates lock is

engaged.

Step Three: Attach field wiring to terminal block.

Caution: If possible, remove field power prior to

proceeding. If not, then EXTREME care MUST be taken

to prevent damage to the module, or even personal injury

due to a short circuit from the live terminal block.

Sales 800-633-0405 www.productivity2000.com

Using the Hardware Configuration tool in the Productivity Suite

programming software, drag and drop the P2-08THM module

into the base configuration.

Select Automatic Module Verification or No Verification and

Enable Hot Swap. Specify Temperature Scale and Burnout

Detection, and use the drop down menu to select module range

and resolution. If desired, assign a User Tagname to each input

point (channel) selected and to each Status Bit Item.

Wiring Options

1Screw Terminal Block (Included)

P2-RTB

(Quantity 1)

2Spring Clamp Terminal Block

P2-RTB-1

(Quantity 1)

Module Configuration

6Tech Support 770-844-4200www.productivity2000.com

Typical Application Example

Process

Variable

(feedback)

Heat

Controller Heater

PID

Output

Oven

Temperature

User’s Desired

Setpoint

Thermocouple

to P2-08THM

P2-08THM

Module

Sales 800-633-0405 www.productivity2000.com

Power On

Appears

initially

These screens will

then auto cycle

This screen will

auto cycle with

status information

PASSED

SELF

TEST

DISPLAY

SETUP

INFO

DISPLAY

UNITS

DECIMAL

COUNTS

DISPLAY

STATUS

INFO

P2-08THM

Fw. Rev.

1.00

16-BIT

7 CH

ENABLED

End of

Status

List

MISSING

CONFIG

DATA

End of

Status

List

SELFTEST

FAIL

REPLACE

MODULE

Hold SEL button down to cycle through primary screens. Release

button to

select

screen.

Error Messages:

An existing error

will be inserted

into the cycling

Status Info screen.

Momentarily

Press SEL

button to

toggle

through

secondary

displays

Note: Volts, Celsius, or

Fahrenheit values are

specified with the P2-08THM

Module Options configuration

dialog box in Productivity Suite

software.

Note: SPARE denotes

deselected channel.

1J 000°F

2E 000°F

3 00.0mV

4 0.000V

5 00.0mV

6 00.0mV

7 00.0mV

8 SPARE

1J 000°F

2E 000°F

3 00.0mV

4 0.000V

5 00.0mV

6 00.0mV

7 00.0mV

8 SPARE

Fault Messages

–

Appear in place

of data during a

fault condition.

Measured temperature > max. temperature of selected range.

Measured temperature < min. temperature of selected range.

Input signal is OPEN circuit. (Thermocouple only)

1 OVER

2 UNDER

3 OPEN

OLED Panel Display

8Tech Support 770-844-4200www.productivity2000.com

Document Name Edition/Revision Date

P2-08THM-DS 1st Ed. 8/15/2014

WARNING: To minimize the risk of potential safety problems, you should

follow all applicable local and national codes that regulate the installation

and operation of your equipment. These codes vary from area to area and

it is your responsibility to determine which codes should be followed, and

to verify that the equipment, installation, and operation are in compliance

with the latest revision of these codes.

Equipment damage or serious injury to personnel can result from the

failure to follow all applicable codes and standards. We do not guar-

antee the products described in this publication are suitable for your

particular application, nor do we assume any responsibility for your

product design, installation, or operation.

If you have any questions concerning the installation or operation of this

equipment, or if you need additional information, please call Technical

Support at 770-844-4200.

This publication is based on information that was available at the time it

was printed. At AutomationDirect.com®we constantly strive to improve

our products and services, so we reserve the right to make changes to

the products and/or publications at any time without notice and without

any obligation. This publication may also discuss features that may not be

available in certain revisions of the product.

Removable Terminal Block Specifications

Part Number P2-RTB (included) P2-RTB-1

Number of

positions 18 Screw Terminals 18 Spring Clamp Terminals

Wire Range

30 - 16 AWG (0.051 - 1.31 mm²)

Solid / Stranded Conductor

3/64 in. (1.2 mm) Insulation Maximum

1/4 in (6 - 7 mm) Strip Length

28-16 AWG (0.081 - 1.31 mm²)

Solid / Stranded Conductor

3/64 in (1.2 mm) Insulation Maximum

19/64 in (7 - 8 mm) Strip Length

Conductors Use Thermocouple Extension wire for thermocouples.

Use copper conductors, 75°C or equivalent for millivolt inputs.

Screw Driver

Width 1/8 in (3.8 mm) Maximum

Screw Size M2 N/A

Screw Torque 2.5 lb·in (0.28 N·m) N/A

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali AutomationDirect Sistema I/O

AutomationDirect

AutomationDirect D2-16ND3-2 Manuale utente

AutomationDirect

AutomationDirect Productivity2000 P2-08AD-1 Manuale utente

AutomationDirect

AutomationDirect T1K-08ND3 Manuale utente

AutomationDirect

AutomationDirect DL405 Manuale utente

AutomationDirect

AutomationDirect Productivity2000 P2-04AD-1 Manuale utente

AutomationDirect

AutomationDirect Terminator Manuale utente

AutomationDirect

AutomationDirect Productivity2000 P2-8AD4DA-2 Manuale utente

AutomationDirect

AutomationDirect Stride SIO-MB12CDR Manuale utente

AutomationDirect

AutomationDirect Stride SIO-MB04RTDS Manuale utente

AutomationDirect

AutomationDirect DL205 Manuale utente

AutomationDirect

AutomationDirect DL305 Manuale utente

AutomationDirect

AutomationDirect Productivity2000 P2-16DAL-1 Manuale utente

AutomationDirect

AutomationDirect Productivity2000 P2-16DA-2 Manuale utente

AutomationDirect

AutomationDirect DL205 Series Manuale del proprietario

AutomationDirect

AutomationDirect T1K-08ND3 Manuale utente

AutomationDirect

AutomationDirect T1F-08DA-2 Manuale utente

AutomationDirect

AutomationDirect Productivity2000 P2-16ADL-1 Manuale utente

AutomationDirect

AutomationDirect Stride SIO-MB04RTDS Manuale utente

Manuali Sistema I/O popolari di altre marche

WAGO

WAGO 750-344 Manuale utente

Teknim

Teknim TWM-1887 Manuale di istruzioni

Intelligent Appliance

Intelligent Appliance IA-2662-E Manuale utente

BERGHOF

BERGHOF ECC DIO 16/16 Manuale di istruzioni

Advantech

Advantech PCM-27J3AU Manuale di installazione e funzionamento

Festo

Festo CP-E08-M12-CL Manuale utente

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manuale utente

Hitachi

Hitachi HX-RIO3 Series Manuale utente

NUUO

NUUO SCB-A08 Manuale utente

M-system

M-system R3Y-RS8 Manuale utente

jablotron

jablotron JB-110N Manuale utente

Omron

Omron SYSMAC C200H Manuale utente

DOLD

DOLD SAFEMASTER M Manuale utente

ABB

ABB OPT-MF-001 Manuale utente

Omron

Omron SYSMAC C2000H Manuale utente

Helmholz

Helmholz TB20 Manuale utente

ICP DAS USA

ICP DAS USA tM-AD2 Manuale utente

Automationdirect.com

Automationdirect.com DL305 Manuale utente