Avdel Avbolt 07220 Manuale utente

Intent of Use

Tool Specification

Tool Dimensions

Specifications

The T10 Installation Tool is basically a Piston and Cylinder Assembly. When coupled Hydraulically and Electrically to a compatible

Hydraulic Power Source and the relevant Nose Assembly is attached, it is then used to install 3/8” Avdelok®, 5/16” to 3/8” Avbolt®and

16mm to 20mm Avseal®in Industrial Environments.

Refer to the table below for the list of applicable fasteners and associated nose equipment.

Refer to the datasheets listed in the table for the relevant nose assembly insructions.

158 mmA

118 mm

98 mm

60 mm

176 mm

Length 158 mm 6.25 in

Body Diameter 60 mm 2.36 in

Height 176 mm 6.93 in

Weight 3.5 kg 7.7 lbs

Stroke 25 mm 1 in

Pull-Force 58kN 13040 lbf

Pull pressure 55.2 mPa 8000 PSI

Return Pressure 20.7 mPa 3000 PSI

Hydraulic Oil ISO VG 46 OR EQUIVALENT

Fastener Range 5 to 10 mm incl. M.G. & Blind Fasteners

Noise Level Below reportable levels

Sound Power Below reportable levels

Vibration Below reportable levels

FASTENER

TYPE SIZE

NOSE ASSEMBLY

PART Nº HAT REF. DIM. ‘A’

NOSE ASSEMBLY

DATASHEET

DIM. ‘B’ PART Nº

07900-00919

07900-00905

07900-00840

73411-03100

73411-05200

73411-05400

16mm

16mm flanged

18mm

20mm

73411-03300

73411-03200

73411-05000

N11

Avbolt

Avseal

Avdelok 3/8î (10mm)

3/8”

5/16”

28mm89mm

27mm86mm

29mm86mm

27mm89mm

N10

This technical datasheet must be read with particular attention to the safety rules and operating instructions

listed in the 07220 (07900-00648), T10 (07900-00820) and T30 (07900-00821) Instruction Manuals, by any

person fitting or operating the Avbolt®nose assemblies and hand tools.

The Avbolt®nose assemblies in combination with the 07220, T10 and T30 tools are designed for placing Avdel®Avbolt®

structural fasteners only. The correct placing tool and nose assembly must be selected for each fastener size as shown in

Table 1 below.

I M P O R T A N T

The tools and nose assemblies must be used in accordance with the safety rules and fitting instructions

contained within this datasheet and the tool instruction manual. The placing of fasteners not included in this

datasheet could have a detrimental impact on the working life of the tool and nose assemblies and could

invalidate the warranty.

The Table 1 below provides a full list of part numbers, nose assemblies and base tools required to place each Avbolt®size.

This table should be used to select and order the correct placing equipment.

Please note that there are two variants of nose equipment available to fit either Avdel®or Huck®hand tools.

For the fitting and servicing instructions for each nose assembly refer to the page number provided in Table 1.

Avbolt®Nose Assembly Instructions

07220, T10 and T30 Tools

Safety Rules

Intent of Use

SIZE

1/4”

5/16”

3/8”

1/2”

5/8”

PART No REF. PAGE

NOSE ASSEMBLY

MODEL PART No

BASE TOOL

PART No

JAWS

07220-07500

07220-07600

07220-07700*

73411-03200

73411-03500

73412-03400

73412-03500

07220-07502

73411-03203

73412-03403

7220

HUCK®256

HUCK®2600

T10

HUCK®2600

T30

HUCK®585

07220-00200

73411-02000

73412-02000

73411-03303 7220*07220-00200*4

07220-07800 73411-033034

T10 73411-02000

73411-03300 73411-033036

73411-03400 73411-033036

*Please note: The 7220 tool is not suitable for high volume placement of 5/16”Avbolt

The tool is only

to be used for demonstration and/or low volume trial purposes.

AVBOLT

Table 1: Nose Equipment Part Numbers

1/4” Avbolt®Nose Assemblies - 07220-07500 and 07220-07600

I M P O R T A N T

The air supply must be disconnected when fitting or removing nose assemblies.

NOSE ASSEMBLY

for Avdel®07220 tool

part nº 07220-07500

ITEM DESCRIPTION PART Nº

1 ANVIL 07220-07501

2 COLLET 07220-07503

3 JAWS 07220-07502

4 SPRING GUIDE 07220-02104

5 SPRING 07220-02103

6 SPACER 07220-07504

7 PINTAIL TUBE 07220-07505

NOSE ASSEMBLY

for Huck®256 tool

part nº 07220-07600

ITEM DESCRIPTION PART Nº

1 ANVIL 07220-07501

2 COLLET 07220-07503

3 JAWS 07220-07502

4 SPRING GUIDE 07220-02104

5 SPRING 07220-02103

6 SPACER - HUCK

07220-07601

7 PINTAIL TUBE 07220-07505

Item numbers in bold refer to nose assembly components in the tables and illustration above.

•Lightly coat Jaws 3with Moly Lithium grease.

•Assemble Spring Guide 4and Spring 5and stand on end on a flat even surface.

•Balance the three Jaws 3on the upper Spring Guide 4.

•Carefully lower Collet 2over the assembled components.

•Holding the assembled collet pointing downwards insert Spacer 6behind the rear Spring Guide 4.

•Insert Pintail Tube 7into the tool head piston bore.

•Holding the tool pointing down, screw the assembled collet fully onto the tool head piston and tighten with a suitable

spanner.

Fitting Instructions

1/4” Avbolt®Nose Assemblies - 07220-07500 and 07220-07600

07220 Tool:

•Place Anvil 1over Collet 2and onto the tool, ensuring that the lugs on the body enter the slots in the

head extension of the tool.

•Turn the reducing adaptor body through 90° then turn the head extension ring until it springs into its position

in the slots of the head extension.

Huck®256 Tool:

•Place Anvil 1over Collet 2and into the tool. Slide the retainer nut over Anvil 1, screw fully onto the

tool and tighten by hand.

Servicing Instructions

Nose assemblies should be serviced at weekly intervals. You should hold some stock of all internal components

of the nose assembly as they will need regular replacement.

•Remove the nose assembly using the reverse procedure to the ‘Fitting Instructions’.

•Any worn or damaged part should be replaced.

•Clean and check wear on Jaws 3.

•Check that Spring 5and Spring Guides 4are not distorted.

•Clean and inspect components, renewing worn or damaged items.

•Assemble according to the ‘Fitting Instructions’.

Fitting Instructions

5/16”Avbolt®Nose Assemblies - 07220-07700 and 07220-07800

I M P O R T A N T

The air supply must be disconnected when fitting or removing nose assemblies.

Please note: The 7220 tool is not suitable for high volume placement of 5/16”Avbolt®. The tool is only to be used

for the demonstration and/or low volume trial purposes.

NOSE ASSEMBLY

for Avdel®07220 tool

part nº 07220-07700

ITEM DESCRIPTION PART Nº

1 ANVIL 07220-07701

2 COLLET 07220-07702

3 JAWS 73411-03303

4 FOLLOWER 07220-07703

5 SPRING 07220-06305

6 SPRING GUIDE 07220-07704 SPRING GUIDE 07220-07704

NOSE ASSEMBLY

for Huck®256 tool

part nº 07220-07800

ITEM DESCRIPTION PART Nº

1 ANVIL 07220-07701

2 COLLET 07220-07702

3 JAWS 73411-03303

4 FOLLOWER 07220-07703

5 SPRING 07220-06305

SHIM 07220-078017

SHIM 07220-07802

Item numbers in bold refer to nose assembly components in the tables and illustration above.

07220 Tool:

•Lightly coat Jaws 3with Moly Lithium grease.

•Assemble Spring Guide 6, Spring 5and Follower 4and stand on end on a flat even surface.

•Balance the three Jaws 3on Follower 4.

•Carefully lower Collet 2over the assembled components.

•Holding the tool pointing down, screw the assembled collet fully onto the tool head piston and tighten with a suitable

spanner.

•Place Anvil 1over Collet 2and onto the tool, ensuring that the lugs on the body enter the slots in the head extension of

the tool.

•Turn the reducing adaptor body through 90° then turn the head extension ring until it springs into its position

in the slots of the head extension.

Fitting Instructions

5/16”Avbolt®Nose Assemblies - 07220-07700 and 07220-07800

Huck®256 Tool:

•Lightly coat Jaws 3with Moly Lithium grease.

•Assemble Spring Guide 6, Shim 7, Sping 5and Follower 4and stand on end on a flat even surface.

•Balance the three Jaws 3on Follower 4.

•Carefully lower Collet 2over the assembled components.

•Holding the assembled collet pointing downwards, insert the Shim 8behind the Spring Guide 6.

•Holding the tool pointing down, screw the assembled collet fully onto the tool head piston and tighten with a suitable

spanner.

•Place Anvil 1over Collet 2and into the tool. Slide the retainer nut over Anvil 1, screw fully onto the

tool and tighten by hand.

Servicing Instructions

Nose assemblies should be serviced at weekly intervals. You should hold some stock of all internal components

of the nose assembly as they will need regular replacement.

•Remove the nose assembly using the reverse procedure to the ‘Fitting Instructions’.

•Any worn or damaged part should be replaced.

•Clean and check wear on Jaws 3.

•Check that Spring 5, Follower 4and Spring Guide 6are not distorted.

•Clean and inspect components, renewing worn or damaged items.

•Assemble according to the ‘Fitting Instructions’.

Fitting Instructions

5/16”Avbolt®Nose Assemblies - 73411-03300 and 73411-03400

I M P O R T A N T

Be sure the tool power supply is turned off before fitting or removing the nose assembly.

10 off

NOSE ASSEMBLY

for Avdel T10 tool

part nº 73411-03300

ITEM DESCRIPTION PART Nº

1 ANVIL 73411-03301

2 COLLET 73411-03302

3 JAWS 73411-03303

4 FOLLOWER 73411-03304

‘O’ RINGS 07003-00426

7 COLLET LOCK 73411-05004

SLEEVE 73411-03305

NOSE ASSEMBLY

for Huck 2600 tool

part nº 773411-03400

ITEM DESCRIPTION PART Nº

1 ANVIL-HUCK 73411-03401

2 COLLET-HUCK 73411-03402

3 JAWS 73411-03303

4 FOLLOWER 73411-03304

5 ‘O’ RINGS 07003-00426

6 SLEEVE 73411-03305

7 COLLET LOCK 73411-05004

Item numbers in bold refer to nose assembly components in the tables and illustration above.

•Lightly coat Jaws 3with Moly Lithium grease.

•On a flat work surface, assemble the Sleeve 6, ‘O’ Rings 5, Follower 4and Jaws 3by stacking vertically in that order.

•Place the Collet 2over the assembled stack, slide to the end of the work surface and with a finger, push the stack fully

inside the Collet.

T10 Tool:

•Holding the tool pointing down, screw the assembled collet fully onto the piston rod until it is flush with the end of the

collet adaptor.

•Insert Collet Lock 7into Collet 2. Rotate Collet 2on the piston rod in either direction until Collet Lock 7slots into the

nearest groove in the collet adaptor. The Collet Lock 7should be flush with the exterior of Collet 2.

•Slide Anvil 1over the collet and screw into the anvil adaptor until it is firm.

•There is a locking ‘O’ Ring which will create a resistance to the final few turns of the nose casing. It is imperative that the

nose casing be hand tightened up against the rear locking face.

Huck®2600 Tool:

•Holding the tool pointing downwards, screw the assembled collet onto the piston rod until it bottoms out.

•Insert Collet Lock 7into Collet 2. Rotate Collet 2 on the piston rod in either direction until Collet Lock 7slots into the

nearest groove on the piston rod. The Collet Lock 7should be flush with the exterior of Collet 2.

•Place Anvil 1over Collet 2and into the tool. Slide the retainer nut over Anvil 1, screw fully onto the tool and tighten by

hand.

Fitting Instructions

5/16”Avbolt®Nose Assemblies - 73411-03300 and 73411-03400

Servicing Instructions

Nose assemblies should be serviced at weekly intervals. You should hold some stock of all internal components

of the nose assembly as they will need regular replacement.

•Remove the nose assembly using the reverse procedure to the ‘Fitting Instructions’.

•Any worn or damaged part should be replaced.

•Clean and check wear on Jaws 3.

•Check that Follower 4, Sleeve 6and ‘O’ Rings 5are not distorted.

•Assemble according to the ‘Fitting Instructions’.

3/8”Avbolt®Nose Assemblies - 73411-03200 and 73411-03500

IMPORTANT

Be sure the tool power supply is turned off before fitting or removing the nose assembly.

NOSE ASSEMBLY

for Avdel®T10 tool

part nº 73411-03200

ITEM DESCRIPTION PART Nº

1 ANVIL 73411-03201

2 COLLET 73411-03202

3 JAWS 73411-03203

4 FOLLOWER 73411-03204

‘O’ RINGS 07003-00426

7 COLLET LOCK 73411-05004

SLEEVE 73411-03205

NOSE ASSEMBLY

for Huck®2600 tool

part nº 73411-03500

ITEM DESCRIPTION PART Nº

1 ANVIL-HUCK

73411-03501

2 COLLET-HUCK

73411-03502

3 JAWS 73411-03203

4 FOLLOWER 73411-03204

5 ‘O’ RINGS 07003-00426

6 SLEEVE 73411-03205

7 COLLET LOCK 73411-05004

10 off

Fitting Instructions

Item numbers in bold refer to nose assembly components in the tables and illustration above.

•Lightly coat Jaws 3 with Moly Lithium grease.

•On a flat work surface, assemble Sleeve 6, ‘O’ Rings 5, Follower 4and Jaws 3by stacking vertically in that order.

•Place Collet 2over the assembly stack, slide to the end of the work surface and with a finger, push the stack fully into

Collet 2.

T10 Tool:

•Holding the tool pointing down, screw the assembled collet onto the piston rod until it is flush with the end of the

collet adaptor.

•Insert Collet Lock 7into Collet 2. Rotate Collet 2on the piston rod in either direction until Collet Lock 7slots into the

nearest groove on the collet adapter. The Collet Lock 7should be flush with the exterior of Collet 2.

•Slide Anvil 1over Collet 2and screw into the anvil adaptor until it is firm.

•There is a locking 'O' ring which will create a resistance to the final few turns of the nose casing. It is imperative that the

nose casing be hand tightened up against the rear locking face.

Huck®2600 Tool:

•Holding the tool pointing down, screw the assembled collet onto the piston rod until it bottoms out.

•Insert Collet Lock 7into Collet 2. Rotate Collet 2on the piston rod in either direction until Collet Lock 7slots into the

nearest groove on the piston rod. The Collet Lock 7should be flush with the exterior of Collet 2.

•Place Anvil 1over Collet 2and into the tool. Slide the retainer nut over the Anvil 1, screw fully onto the tool and tighten by

hand.

3/8”Avbolt®Nose Assemblies - 73411-03200 and 73411-03500

Nose assemblies should be serviced at weekly intervals. You should hold some stock of all internal components of the nose

assembly as they will need regular replacement.

•Remove the nose assembly using the reverse procedure to the ‘Fitting Instructions’.

•Any worn or damaged part should be replaced.

•Clean and check wear on Jaws 3.

•Check that Follower 4, Sleeve 6and ‘O’ Rings 5are not distorted.

•Assemble according to the ‘Fitting Instructions’.

Servicing Instructions

Altri manuali per Avbolt 07220

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Avdel Utensili elettrici

Manuali Utensili elettrici popolari di altre marche

AEG

AEG OMNI-JS Manuale utente

SIP

SIP 01533 Manuale utente

Ribimex

Ribimex PRS499 Manuale utente

3M Fiber Optic Connector Crimp Tool Manuale utente

Ryobi

Ryobi P524 Manuale utente

ROJEK

ROJEK FSN 300A Manuale utente

Kemper

Kemper 1740PRO Manuale utente

WABCO

WABCO OptiTire Manuale utente

EINHELL

EINHELL TE-MS 18/210 Li Manuale utente

Orgapack

Orgapack OR-T 85 Guida rapida

TOUGHCUT

TOUGHCUT Diamond 400 Manuale utente

Yaros

Yaros PB-3603 Manuale utente

Fein

Fein BSS 2.0 E Guida all'installazione

Baileigh Industrial

Baileigh Industrial SS-2725 Manuale utente

Milwaukee

Milwaukee 2674-20 Manuale utente

Fein

Fein BLs 1.6 Manuale utente

Princess

Princess Electric Multi Sharpener Manuale utente

FOREDOM

FOREDOM K.1050 Manuale