Baby Lock Model BLCS Manuale utente

SERVICE MANUAL

MODEL BLCS

Vol 3.1

From

Serial Numbers

For U.S.A. For Canada For Europe,

Australia,NZ

100061100390 100383

1.Construction of Covers

10.1

4.6

2.0

Distance of chain looper tip from

center of chain looper shaft

Distance of lower looper tip from

center of lower looper shaft

Distance of upper looper tip

from right side of overlock

right needle(O2)

Distance of lower looper tip

from right side of overlock

right needle(O2)

Distance of chain looper tip

from right side of chain

right needle(C3)

55.4

72.8

4.9 8.6

Height of

feed dog

Height of

presser foot

Height of overlock

right needle(O2)

Adjusting gauge

For BLE8

2. Adjustment of Needle,Chain lopper & Presser foot

Height of presser foot

4.8 +0.1

R72.4

0.1

Height of needle Chain looper adjustment

1.8 0

+0.1

ELx705CF 90/14 ELx705CF 90/14

ELx705CF 90/14

C3 Needle

Needle plate

12.5+0.05

C3 Needle

2.3+0.2

Chain

Needle

Chain

Needle

Needle guard adjustment

0.2-0.3

FRONT

SIDE

FRONT

SIDE

0-0.02

Chain needle

front needle

guard

Back

needle guard

C3Needle

Chain needle

& Chain looper

0-0.1

3. Height of feed dog

CORRECT HEIGHT – When feed dogs are top position, make sure the clearance

of 0.9mm between presser foot and needle plate.

4. Tension release & Dropped feed dog adjustment

4-1.Tension release

a) In case you replace face cover, make sure the tension release lever

catches the Tension release pin correctly (fig.A)

b) Double check disks are open perfectly when presser bar lifter is lifted.

4-2. Dropped feed dog adjustment

Make sure feed dog height is correct,before you adjust following items.

a) Loosen adjusting screw (B).

b) Lift the presser bar lifter and make sure feed dog is dropped position.

c) Rotate machine pully, Make sure Feed dog crutch arm (E) swings up and

down.

d) Tighten the screw (B) until Feed dog crutch arm does not swing.

e) Drop the presser bar lifter, make sure dropped feed dog mechanism does

work correctly when presser bar lifter is lift position.

0.9 +0.1

3.Height of feed dog

4.Tension release & Dropped feed dog adjustment

5. Checking threading steel pipe joint

a) Set the machine for looper threading.

b) Move the lock button release lever slightly to the right.

c) Check the connecting point whether the looper threading pipe joint and threading

steel pipe is fitted each other properly.

6. Checking pump

6-1 Checking deflate from pump

Holding the pump tube 6, push down the pump lever 15 and check if air is deflated

from pump or not.

6-2 Replacement of Piston Cap

a) Bring the pump lever to the lowest position and fix it with Scotch tape or something like that.

b) Remove bace plate.

c) Remove piston driving arm fixing screw 11 (SM3005IK).

d) Remove piston driving arm from piston driving shaft.

(It will be easy to remove the arm from the shaft, if you push the shaft to the rightward direction.)

e) Remove piston assembly from cylinder

(It will be easy to remove piston assenbly from cylinder, when the needle is in the lowest position.)

f) Replace piston cap.

g) Greace piston cap a little bit.(MOLYKOTE EM-50L)

h) Return piston assembly to cylinder.

i) Fit piston driving arm to piston driving shaft properly and tighten fixing screw SM3005IK firmly.

(It will be easy to fit the armto the shaft, if you push the shaft to the leftward direction.)

j) Check and confirm whether the pump works properly or not.

k) fix bace plate.

Threading steel

pipe

Proper position Unproper position

Joint

5.Checking thread

steel pipe joint

6.Checking pump

8. Trouble Shooting

7. Adjustment of thread take-up

7-1 NEEDLE THREADS ARE UN BALANCED ;

* Is the BLCS threaded correctly? See Instruction Book P.14,15.

* Are the threads snapped in the head guide? See Instruction Book P.15.

* Are the threads recommended high quality? See Instruction Book P.7.

7-2 LOOPER THREADS ARE UNBALANC ED ;

* Is the BLCS threaded correctly? See Instruction Book P.14,15.

* Are the threads snapped in the head guide? See Instruction Book P.15.

* Are the threads recommended high quality? See Instruction Book P.7.

7-3 THREAD BREAKS ;

* Is the BLCS threaded correctly? See Instruction Book P.14,15.

* Are the threads snapped in the head guide? See Instruction Book P.15.

* Are the threads recommended high quality? See Instruction Book P.7.

7-4 JET AIR THREADER DOES NOT WORK

*Is air deflated from pump? See P.13.

*Are pipes connected properly? See P.13.

*Are there any lints or thread in pipes?

BLCS3

Correct Position

(Thread take-up is

lowest position.)

CORRECT POSITION: When thread take-up is lowest position, thread take-up and

thread guide are same position. See illustration below.

a). Rotate the machine pully and bring thread take-up at the lowest position.

b). Loosen thread take-up height position adjusting screws.

c). Adjust the thread take-up to correct position. See illustration below.

d). Tighten the fixing screws.

Thread take-up

height position

adjusting screws

Altri manuali per Model BLCS

Indice

Altri manuali Baby Lock Macchina da cucire

Baby Lock

Baby Lock Molly BL30A Manuale tecnico

Baby Lock

Baby Lock Symphony BLSY Manuale utente

Baby Lock

Baby Lock zeal BL35B Manuale tecnico

Baby Lock

Baby Lock Enterprise Guida all'installazione

Baby Lock

Baby Lock Elissimo & Elissimo GOLD BLSO-BF2 Manuale utente

Baby Lock

Baby Lock Model BLCS Manuale utente

Baby Lock

Baby Lock Sashiko BLQK Manuale tecnico

Baby Lock

Baby Lock BLE1 Manuale utente

Baby Lock

Baby Lock Quest BLQ2 Manuale tecnico

Baby Lock

Baby Lock embellisher EMB12 Manuale tecnico

Baby Lock

Baby Lock Anna BL20A Istruzioni per il montaggio

Baby Lock

Baby Lock Sashiko Manuale utente

Baby Lock

Baby Lock ellegante BLG guid Manuale tecnico

Baby Lock

Baby Lock BLSA2 Manuale tecnico

Baby Lock

Baby Lock imagine Manuale utente

Baby Lock

Baby Lock imagine wave BLE3ATW Manuale utente

Baby Lock

Baby Lock emore BLMR Manuale tecnico

Baby Lock

Baby Lock Ellure (BLR) Manuale tecnico

Baby Lock

Baby Lock Pro Line BL4-838D Manuale utente

Baby Lock

Baby Lock A-LINE Lauren BL450A Manuale tecnico

Baby Lock

Baby Lock A-LINES Sofia BL137A Manuale utente

Baby Lock

Baby Lock Pro-Stitcher Lite BLPS-LITEG-VF Manuale utente

Baby Lock

Baby Lock Flourish BLMFO Manuale utente

Baby Lock

Baby Lock Elizabeth BL200A Manuale utente

Manuali Macchina da cucire popolari di altre marche

Riccar

Riccar RL634DE Manuale utente

Singer

Singer 2517 Manuale utente

Pfaff

Pfaff 3307-1 SERIES Manuale utente

Janome

Janome Quilt Maker Pro 18 VERSA Manuale utente

Siruba

Siruba C007JP Manuale utente

Husqvarna Viking

Husqvarna Viking Designer SE Manuale utente

Singer

Singer 148-5 Manuale utente

IKEA

IKEA SY Manuale utente

Pfaff

Pfaff 571 Manuale utente

Singer

Singer 15-91 Manuale utente

Brother

Brother BB370 Manuale utente

Pegasus

Pegasus WT100 Series Manuale utente

Reliable

Reliable 7100DB Manuale utente

Pfaff

Pfaff 937 Manuale utente

Singer

Singer 6038 Manuale utente

Singer

Singer 413K Manuale utente

Pfaff

Pfaff 1471 E1 Manuale utente

Kenmore

Kenmore 16677 - Serger Sewing Machine Manuale utente