BAFANG DP C244.CAN Manuale utente
1
BF-UM-C-DP C244-EN July 2022
USER MANUAL FOR DISPLAY
CONTENT
7.1 Important Notice 2
7.2 Introduction of Display 2
7.3 Product Description 3
7.3.1 Specifications 3
7.3.2 Functional Overview 3
7.4 Display 4
7.5 Key Definition 4
7.6 Normal Operation 5
7.6.1 Power ON/OFF 5
7.6.2 Power Assist Mode Selection 5
7.6.3 Multifunction Selection 6
7.6.4 Headlights / Backlighting 6
7.6.5 Walk Assistance 6
7.6.6 Battery Capacity Indication 7
7.6.7 USB Charge Function 7
7.6.8 Bluetooth Function 7
7.7 Settings 8
7.7.1 "Display Setting" 8
7.7.2 "Information" 10
7.8 Error Code Definition 12
7.9 Warn Code Definition 16
7 USER MANUAL FOR
DP C244.CAN/ DP C245.CAN
2BF-UM-C-DP C244-EN July 2022
7.2 INTRODUCTION OF DISPLAY
• Model: DP C244.CAN/ DP C245.CAN
• The housing material is ABS; the LCD display
windows is made of tempered glass:
• The label marking is as follows:
Note: Please keep the QR code label attached
to the display cable. The information from the
Label is used for a later possible software
update.
7.1 IMPORTANT NOTICE
• If the error information from the display
cannot be corrected according to the inst-
ructions, please contact your retailer.
• The product is designed to be waterproof. It
is highly recommended to avoid submerging
the display under water.
• Do not clean the display with a steam jet,
high-pressure cleaner or water hose.
• Please use this product with care.
• Do not use thinners or other solvents to
clean the display. Such substances can
damage the surfaces.
• Warranty is not included due to wear and
normal use and aging.
3
BF-UM-C-DP C244-EN July 2022
USER MANUAL FOR DISPLAY
7.3 PRODUCT DESCRIPTION
7.3.1 Specifications
• Operating temperature: -20℃~45℃
• Storage temperature: -20℃~60℃
• Waterproof: IP65
• Storage Humidity: 30%-70% RH
7.3.2 Functional Overview
• CAN communication protocol
• Speed indication (including the real-time
speed, max. speed and average speed)
• Unit switching between km and mile
• Battery capacity indicaton
• Automatic sensors explanation of the light-
ing system
• Brightness setting for backlight
• 6 power assist modes
• Mileage indication (including single-trip
distance TRIP and total distance ODO, the
highest mileage is 99999)
• Intelligent indication (including remaining
distance RANGE and energy consumption
CALORIE)
• Error code indication
• Walk assistance
• USB charge (5V and 500mA)
• Service indication
• Bluetooth Function (only in DP C245.CAN)
4BF-UM-C-DP C244-EN July 2022
7.5 KEY DEFINITION
Power On/Off
7.4 DISPLAY
1
7
8
6
5
1Headlight indication
2USB charge indication
3Service indication
4Bluetooth indication
(only light up in DP C245.CAN)
5Power assist mode indication
6Multifunction indication
7Battery capacity indication
8Speed in real-time
2 3 4
Up/ Headlight
Down/ Walk assistance
5
BF-UM-C-DP C244-EN July 2022
USER MANUAL FOR DISPLAY
7.6 NORMAL OPERATION
7.6.1 Power ON/OFF
Press and hold (>2S) to power on the HMI, and the HMI begin to show the boot up LOGO.
Press and hold (>2S) again to power off the HMI.
If the automatic shutdown time is set to 5 minutes (set in function "Auto Off"), the HMI will be auto-
matically turned off within this set time, when it is not operated.
7.6.2 Power Assist Mode Selection
When HMI powers on, briefly press or to select the power assist mode and change the
output power. The lowest mode is E, the highest mode is B (which can be set). On the default is
mode E, number “0”means no power assistance.
Mode Color Definition
Eco green the most economic mode
Tour blue the most economic mode
Sport indigo the sport mode
Sport+ red the sport plus mode
Boost purple the strongest sport mode
6BF-UM-C-DP C244-EN July 2022
7.6.3 Multifunction Selection
Briefly press button to switch the different function and information.
Circularly show single trip distance (TRIP,km) →total distance (ODO,km) →maximum speed (MAX,k-
m/h) →average speed (AVG,km/h) →remaining distance (Range,km) →riding cadence (Cadence,rpm)
→energy consumption (Cal,KCal) →riding time (TIME,min) →cycle.
7.6.4 Headlights / Backlighting
Press and hold (>2S) to turn on the headlight and reduce the backlight brightness.
Press and hold (>2S) again to turn off the headlight and increase the backlight brightness.
The brightness of backlight can be set in function“Brightness” within 5 levels.
7.6.5 Walk Assistance
Note: The walk assistance can only be activated with a standing pedelec.
Briefly press button until this symbol appears. Next keep pressing the button until the
walk assistance is activated and the symbol is flashing.(If no speed signal is detected, the
real-time speed is shown as 2.5km/h.) Once releasing the button, it will exit the walk assistance
and the symbol stops flashing. If no operation within 5s, the display will automatically return to
0 mode.
7
BF-UM-C-DP C244-EN July 2022
USER MANUAL FOR DISPLAY
7.6.6 Battery Capacity Indication
The percentage of current battery capacity
and total capacity is displayed from 100% to
0% according to the actual capacity.
7.6.7 USB Charge Function
When the HMI is off, insert the USB device
to the USB charging port on the HMI, and
then turn on HMI to charge. When the HMI
is on, it can direct charge for USB device. the
maximum charging voltage is 5V and the
maximum charging current is 500mA.
7.6.8 Bluetooth Function
Note: Only DP C245.CAN is the Bluetooth
version.
DP C245 equipped with Bluetooth 5.1 can
be connected to the Bafang Go+ APP.
This display can be connected to the SIGMA
heartbeat band and shows it on display, and
can also send data to the mobile phone.
The data that can be sent to the mobile
phone are as follow:
No. Function
1 Speed
2 Battery capacity
3 Support level
4 Battery info.
5 Sensor signal
6 Remaining distance
7 Energy consumption
System part info.
9 Current
10 Heartbeat
11 Single distance
12 Total distance
13 Headlight status
14 Error code
(Bafang Go+ for AndroidTM and iOSTM )
8BF-UM-C-DP C244-EN July 2022
7.7 SETTINGS
After the HMI powered on, press and hold
and button (at the same time) to enter into
the setting interface. Briefly press (<0.5S)
or button to select “Setting”,“Information”
or “Exit” , then briefly press (<0.5S) button
to confirm.
7.7.1 “Setting” interface
After the HMI powered on, press and hold
and button to enter into the setting
interface. Briefly press (<0.5S) or to
select "Setting" and then briefly press
(<0.5S) to confirm.
7.7.1.1 “Unit” Selections in km/Miles
Briefly press or to select “Unit”, and
briefly press to enter into the item. Then
choose between “Metric” (kilometer) or
“Imperial” (mile) with the or button.
Once you have chosen your desired
selection, press the button (<0.5S) to
save and exit back to the "Setting" interface.
Note: If you choose "Metric", all the data
displayed on the HMI are metric.
7.7.1.2 “Auto Off” Set automatic Off time
Briefly press or to select “Auto Off”,
and briefly press to enter into the item.
Then select the automatic Off time as “OFF”/
“1”/“2”/“3”/“4”/“5”/“6”/“7”/“8”/“9”/“10”
with the or button. Once you have
chosen your desired selection, press the
button (<0.5S) to save and exit back to the
"Setting" interface.
Note: “OFF” means the "Auto Off" function
is off.
7.7.1.3 “Brightness” Display brightness
Briefly press or to select “Bright-
ness”, and briefly press to enter into the
item. Then select the percentage as “100%”
/ “75%” / “50%” / “25%” with the or
button. Once you have chosen your
desired selection, press the button
(<0.5S) to save and exit back to the "Setting"
interface.
7.7.1.4 “AL Sensitivity” Set light sensitivity
Briefly press or to select “AL
Sensitivity”, and briefly press to enter
into the item. Then select the level of the
light sensitivity as “OFF”/“1”/ “2”/“3”/“4”/“5”
with the or button. Once you have
chosen your desired selection, press the
button (<0.5S) to save and exit back to the
"Setting" interface.
9
BF-UM-C-DP C244-EN July 2022
USER MANUAL FOR DISPLAY
Note: “OFF” means light sensor is off. Level
1 is the weakest sensitivity and level 5 is the
strongest sensitivity.
7.7.1.5 “TRIP Reset” Set reset function for
single-trip
Briefly press or to select “TRIP
Reset”, and briefly press to enter into the
item. Then select “NO”/“YES” (“YES”- to
clear, “NO”-no operation) with the or
button. Once you have chosen your
desired selection, press the button
(<0.5S) to save and exit back to the "Setting"
interface.
Note: The riding time(TIME), average speed
(AVG) and maximum speed (MAXS) will be
reset simultaneously when you reset TRIP.
7.7.1.6 “Service” Turn on/off the Service
indication
Briefly press or to select “Service”,
and briefly press to enter into the item.
Then select “OFF”/“ON” (“ON” means
Service indication is on; “OFF” means Service
indication is off) with the or button.
Once you have chosen your desired
selection, press the button (<0.5S) to
save and exit back to the "Setting" interface.
Note: The default setting is OFF. If the ODO
is more than 5000 km, the "Service" indica-
tion and mileage indication will flash for 4S.
7.7.2 "Information"
After the HMI powered on, press and hold
and to enter into the setting
function. Briefly press (<0.5S) or to
select "Information" and then briefly press
(<0.5S) to confirm.
Note: All information here cannot be changed, it is
to be viewed only.
7.7.2.1 “Wheel Size”
After entering the "Information" page, you
can see "Wheel Size --Inch" directly.
7.7.2.2 “Speed Limit”
After entering the "Information" page, you
can see "Speed Limit --km/h" directly.
7.7.2.3 “Battery Info”
Briefly press or to select “Battery
Info”, and briefly press to enter, then
briefly press or to view the battery
data (b01 → b04 → b06 → b07 → b08 → b09
10 BF-UM-C-DP C244-EN July 2022
→ b10 → b11 → b12 → b13 → d00 → d01 →
d02 → … → dn).
Press the button (<0.5S) to exit back to
the "Information" interface.
Note: If the battery doesn't have commu-
nication function, you won’t see any data
from battery.
View the battery information
View the hardware and software version of battery
Code Code Definition Unit
b01 Current temperature ℃
b04 Battery voltage mV
b06 Current mA
b07 Remaining battery
capacity mAh
b08 Battery capacity of
Full charged mAh
b09 Relative SOC %
b10 Absolute SOC %
b11 Cycle Times times
b12 Max Uncharge Time Hour
b13 Last Uncharge Time Hour
Code Code Definition Unit
d00 The number of cell
d01 Voltage Cell 1 mV
d02 Voltage Cell 2 mV
dn Voltage Cell n mV
NOTE: If no data is detected, "--" will be displayed.
7.7.2.4 “Display Info”
Briefly press or to select ”Display
Info”, and briefly press to enter, briefly
press or to view“Hardware Ver” or
“Software Ver”.
Press the button (<0.5S) to exit back to
the "Information" interface.
7.7.2.5 “Ctrl Info”
Briefly press or to select ”Ctrl Info”,
and briefly press to enter, briefly press
or to view“Hardware Ver” or
“Software Ver”.
Press the button (<0.5S) to exit back to
the "Information" interface.
7.7.2.6 “Sensor Info”
Briefly press or to select ”Sensor
Info”, and briefly press to enter, briefly
press or to view“Hardware Ver” or
“Software Ver”.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali BAFANG Monitor
BAFANG
BAFANG M300 Manuale utente
BAFANG
BAFANG DP C07.CAN Manuale utente
BAFANG
BAFANG DP C01.UART Manuale utente
BAFANG
BAFANG UB400 Manuale utente
BAFANG
BAFANG DP E12.UART Manuale utente
BAFANG
BAFANG DP C230.CAN Manuale utente
BAFANG
BAFANG DP C010.CB Manuale utente
BAFANG
BAFANG Luna X-1 Manuale utente
BAFANG
BAFANG Ebike Essentials DPC18 Manuale utente
BAFANG
BAFANG C961 Manuale utente
