Bafo BF-120 Manuale utente
USER’S MANUAL
USB TO IrDA ADAPTER
BF-120
USB To Irda Adapter User’s Manual 1
CONTENT
1. Introduction----------------------------------------------------------------------------------2
2. Application & Connection-------------------------------------------------------------2
3. Package Content--------------------------------------------------------------------------2
4. Product Features--------------------------------------------------------------------------2
5. System Requirements-------------------------------------------------------------------3
6. Driver Installation-------------------------------------------------------------------------3
6.1 Windows®98 Driver Installation---------------------------------------------------3
6.2 Windows®ME Driver Installation--------------------------------------------------6
6.3 Windows®2000 Driver Installation------------------------------------------------9
6.4 Windows®XP Driver Installation-------------------------------------------------11
7. Disclaimer-----------------------------------------------------------------------------------13
8. FCC Statement----------------------------------------------------------------------------14
9. Technical Support-----------------------------------------------------------------------14
USB To Irda Adapter User’s Manual 2
1. Introduction
USB to IrDA bridge adapter is for enabling IrDA wireless data communication
through a standard USB port. Powered from USB bus, this product does not require
any external power adapter. It supports SIR (2.4Kbps to 115.2Kbps), MIR (576Kbps
to 1152Kbps), and FIR(4Mbps) modes. The effective data transmission distance is
from 0 to 1M. The reception or viewing angle in a typical environment is 30o (+ / -15o).
Use the product; you could transfer data with wireless connection for PC, PDA,
digital camera, scanner andprinter.
2. Application & Connection
Wireless data transfer between desktop PC and notebook PC, PDA, Digital Camera,
Scanner and Printer
Files Sharing, Photo transfer, Printing, Data Exchange and Synchronization
3. Package Content
Hardware
§USB to IrDA Adapter, USB Cable
Software
§Software driver on CD
§User’s Manual
4. Product Features
§Easily enable IrDA function on the desktop PC through USB port
§USB Plug and Play convenience
§Fully compatible with IrDA 1.1 and USB 1.1 specification
§Compatible with FIR 4Mbps, MIR, SIR and ASK 56Kbps
§No power adapter required
§Low power consumption
USB To Irda Adapter User’s Manual 3
5. System Requirements
§IBM PC 486DX4-100 MHz or higher or compatible system
§Available USB port
§CD-ROM drive
§Windows®98, Windows®ME, Windows®2000, Windows®XP.
6. Driver Installation
NOTICE: Before you install the driver to your computer, please do not connect
the USB to IrDA Adapter to your computer.
6.1 Windows®98 Driver Installation
Following the steps below to install driver of USB to IrDA Adapter:
6.1.1 Power on the computers that you will connect the USB to IrDA Adapter
and make sure the USB port is enabled and can working properly.
6.1.2 Put the driver CD into the CD-ROM and run theD:\Driver\BF-120
\Infineon\Windows\SETUP.EXE or D:\Driver\BF-120\Vishay 6101E
\Windows\SETUP.EXE or D:\Driver\BF-120\Vishay 6102F\Windows
\SETUP.EXE. (According with the different transceiver type, you
have to install the different driver.)
6.1.3 As the windows appear as below, click “NEXT” to continue.
USB To Irda Adapter User’s Manual 4
6.1.4 You can choose the destination folder that you want to install or use the
default setting (C:\WINDOWS\Sigmatel\USB-IR).
6.1.5 The windows will install the driver into your system.
6.1.6 As the Windows appear as below, please plug theUSB to IrDA
Adapter into the USB port.
6.1.7 Windows will detect the new device, in this procedure you may have to
put your Win98CD into the CD-ROM
6.1.8 Windows will detect the new device (Sigma Tel USB-IrDA Dongle) and
install the driver.
USB To Irda Adapter User’s Manual 5
6.1.9 As the windows appear as below, you have to reboot your computer.
6.1.10 After the windows restart, you have to check “My Computer”-“Control
Panel”-“System”-“Device Manager”, you can see a new “Infrared
Communication Device” appear and “SigmaTel USB-IrDA Dongle”
under the Network Adapter, “Virtual Infrared COM Port” and “Virtual
Infrared LPT Port” under the Ports (COM &LPT)item.
USB To Irda Adapter User’s Manual 6
6.2 Windows®ME Driver Installation
Following the steps below to install driver of USB to IrDA Adapter:
6.2.1 Power on the computers that you will connect the USB to IrDA Adapter
and make sure the USB port is enabled and working properly.
6.2.2 Put the driver CD into the CD-ROM and run theD:\Driver\BF-120
\Infineon\Windows\SETUP.EXE or D:\Driver\BF-120\Vishay 6101E
\Windows\SETUP.EXE or D:\Driver\BF-120\Vishay 6102F\Windows
\SETUP.EXE. (According with the different transceiver type, you
have to install the different driver.)
6.2.3 As the windows appear as below, click “NEXT” to continue.
6.2.4 You can choose the destination folder that you want to install or use the
default setting (C:\WINDOWS\Sigmatel\USB-IR).
USB To Irda Adapter User’s Manual 7
6.2.5 The windows will install the driverinto your system..
6.2.6 As the Windows appear as below, please plug theUSB to IrDA
Adapter into the USB port.
6.2.7 Windows will detect the new device (Sigmal Tel USB-IrDA Dongle) and
install the driver for the new device.
6.2.8 As the windows appear as below, you have to reboot your computer.
USB To Irda Adapter User’s Manual 8
6.2.9 After the windows restart, you have to check “My Computer”-“Control
Panel”-“System”-“Device Manager”, you can see a new “Infrared
Communication Device” appear and “SigmaTel USB-IrDA Dongle”
under the Network Adapter, “Virtual Infrared COM Port” and “Virtual
Infrared LPT Port” under the Ports (COM&LPT)+
USB To Irda Adapter User’s Manual 9
6.3 Windows®2000 Driver Installation
Following the steps below to install driver of USB to IrDA Adapter USB cable:
6.3.1 Power on the computers that you will connect the USB to IrDA Adapter
and make sure the USB port is enabled and can working properly.
6.3.2 Put the driver CD into the CD-ROM and run theD:\Driver\BF-120
\Infineon\Windows\SETUP.EXE or D:\Driver\BF-120\Vishay 6101E
\Windows\SETUP.EXE or D:\Driver\BF-120\Vishay 6102F\Windows
\SETUP.EXE. (According with the different transceiver type, you
have to install the different driver.)
6.3.3 As the windows appear as below, click “NEXT” to continue.
6.3.4 You can choose the destination folder that you want toinstall or use the
default setting (C:\WINNT\SigmaTel\USB-IR), thenclick “NEXT” to
continue.
Indice
Altri manuali Bafo Adattatore
