Banner VE200G1B Manuale utente

Quick Start Guide

Self-contained Smart Camera with User-Friendly Vision Manager Software

This guide is designed to help you set up and install the VE Series Smart Camera. For complete information on programming, performance,

troubleshooting, dimensions, and accessories, please refer to the Instruction Manual at www.bannerengineering.com. Search for p/n 191666 to view

the Instruction Manual. Use of this document assumes familiarity with pertinent industry standards and practices. More details are available in the

online help.

WARNING: Not To Be Used for Personnel Protection

Never use this device as a sensing device for personnel protection. Doing so could lead to serious injury or death. This device

does not include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. A sensor

failure or malfunction can cause either an energized or de-energized sensor output condition.

CAUTION: Electrostatic Discharge

Avoid the damage that electrostatic discharge (ESD) can cause to the Sensor.

Always use a proven method for preventing electrostatic discharge when installing a lens or attaching a cable.

CAUTION: Hot Surface

Use caution when handling the camera. The surface of the camera may be hot during operation and immediately after use.

Models

Model 1Resolution Type

VE200G1A WVGA, 752 × 480 pixels grayscale Vision

VE201G1A 1.3 MP, 1280 × 1024 pixels grayscale Vision

VE202G1A 2 MP, 1600 × 1200 pixels grayscale Vision

VE205G1A 5 MP, 2592 × 2048 pixels grayscale Vision

VE200G1B WVGA, 752 × 480 pixels grayscale ID

VE201G1B 1.3 MP, 1280 × 1024 pixels grayscale ID

VE202G1B 2 MP, 1600 × 1200 pixels grayscale ID

VE205G1B 5 MP, 2592 × 2048 pixels grayscale ID

VE200G1C WVGA, 752 × 480 pixels grayscale Vision + ID

VE201G1C 1.3 MP, 1280 × 1024 pixels grayscale Vision + ID

VE202G1C 2 MP, 1600 × 1200 pixels grayscale Vision + ID

VE205G1C 5 MP, 2592 × 2048 pixels grayscale Vision + ID

Features

Figure 1. Sensor Features

1. Display

2. Buttons

3. Pass/Fail indicator (green/red)

4. Ready/Trigger indicator (green/amber)

5. Power/Error indicator (green/red)

6. Ethernet indicator (amber), not shown

7. Ethernet connection

8. Light connection

9. Power, Discrete I/O connection

1Model VE202G2A, 2 MP, 1600 × 1200 grayscale with 4-pin D-code M12 Ethernet connection is also available.

VE Series Smart Camera

Original Document

191667 Rev. J

17 March 2021

191667

Display

Figure 2. Display with Home Screen

The display is a 2-line, 8-character LCD. The main screen is the Home

Screen, which shows the name of the current inspection and the slot

number (inspection location). Use the display to view or change several

sensor settings.

Indicators

Four LED indicators provide ongoing indication of the sensing status.

Power/Error Indicator

Green = Normal operation

Red = System error

Ready/Trigger Indicator

Green = Ready for trigger

Yellow = Trigger is active

OFF = Not ready for a trigger, triggers will be missed

Pass/Fail Indicator

Green = Previous inspection passed

Red = Previous inspection failed

OFF = No trigger since power up

Ethernet Indicator

Amber solid = Ethernet connection

Amber ﬂashing = Ethernet activity

OFF = no connection

Buttons

Use the sensor buttons Down , Up , Enter , and Escape to conﬁgure several sensor settings and to access sensor information.

See Figure 11 on p. 9 for additional information on using the buttons.

Vision Manager Software

Set up the VE Series Smart Camera using the free Vision Manager Software, available for download at www.bannerengineering.com.

This easy-to-use image processing software provides a variety of tools and capabilities to solve a wide range of vision applications such as item

detection, part positioning, feature measurement, ﬂaw analysis, and barcode reading. Run-time editing allows you to make changes to an inspection

while the sensor is running, reducing costly downtime. Vision Manager also includes a full software emulator, allowing users to develop or

troubleshoot inspections ofﬂine, without a sensor.

Password-protected user proﬁles are also available to enable different levels of access to the tools and data.

Use Vision Manager to conﬁgure Banner vision devices including iVu Vision Sensors and VE Smart Cameras.

Installation Instructions

Install the Accessories

Figure 3. Install the Accessories

1. VE sensor

2. O-ring (used with the sealed lens cover)

3. C-mount lens (available separately)

4. Filter (optional)

5. Sealed lens cover (optional)

An external light (optional) is not shown.

Note: A sealed lens cover and a ring light cannot be used together.

1. If you are using a sealed lens cover: Remove the black thread protector (not shown) from the sensor (1).

2. If you are using a sealed lens cover: Fit a single o-ring (2) into the undercut area behind the sensor threads.

3. Remove the yellow temporary imager cover (not shown) from the sensor.

CAUTION: Do not remove the imager cover until you are ready to install the lens. Do not touch the imager. Dirt or dust

on the imager can affect sensing reliability.

4. Remove any protective covers from the lens. Handle the lens carefully to avoid smudges and dirt on the optical elements.

5. Thread the lens (3) onto the sensor.

6. Make sure that the lens is focused; see Acquire a Good Image on p. 5.

7. Use the thumbscrews on the lens to lock the focus and aperture rings and to prevent movement that can occur during cleaning or

accidental contact.

8. If you are using a ﬁlter: Thread the ﬁlter (4) onto the front of the C-mount lens.

9. If you are using a linear polarization ﬁlter: Rotate the outer portion of the ﬁlter mount to determine the position where glare is reduced the

most, and use the locking thumbscrew to fasten the ﬁlter in position.

10. If you are using a sealed lens cover: Thread the sealed lens cover (5) onto the threaded portion of the sensor.

11. Or, if you are using an external light bracket: Attach an external light bracket to the sensor using the provided hardware kit.

VE Series Smart Camera

2 www.bannerengineering.com - Tel: + 1 888 373 6767 P/N 191667 Rev. J

Note: For optimal imaging, provide adequate dissipation of heat. A good heat conductor, such as aluminum, may be required.

Mount the Sensor

1. If a bracket is needed, mount the device onto the bracket.

2. Mount the device (or the device and the bracket) to the machine or equipment at the desired location. Do not tighten the mounting screws at

this time.

CAUTION: This device accepts M3×0.5-h6 screws. Engaging the screws more than 3.00 mm will damage the device.

3. Check the device alignment.

4. Tighten the mounting screws to secure the device (or the device and the bracket) in the aligned position.

Connect the Cables

Figure 4. Cable Connections

123

1. Power, Discrete I/O connection

2. Light connection

3. Ethernet connection

4. Ethernet indicator

1. Connect the Ethernet cable to the sensor (3) and to the computer or Ethernet switch.

2. Connect the power, discrete I/O cable to the sensor (1), and the leads to the appropriate locations. See Table 1 on p. 3 for the power,

discrete I/O connections.

3. Connect the external light cable (optional) to the light connection (2) if the light is powered by the sensor.

CAUTION: Use Appropriate Power

If the light is powered by the sensor, the sensor power source must be 24 V dc. This connection is for Banner lights

only.

Table 1: Power and I/O Pinouts

Pin Wire Color Description Direction

1 White Discrete I/O #3 Input/Output

2 Brown 12 V dc to 30 V dc Input

3 Green I/O output common

Important: For PNP (sourcing) outputs connect pin 3 to +V dc, for

NPN (sinking) outputs connect pin 3 to 0 V dc. The discrete I/O pins

are 1, 5, 8, 10, and 11.

4 Yellow RS-232 TX (transmit) Output

5 Gray Discrete I/O #5 Input/Output

6 Pink Trigger input Input

7 Blue Common Input

8 Red Discrete I/O #2 Input/Output

9 Orange I/O input common

Important: For PNP (sourcing) inputs connect pin 9 to 0 V dc, for NPN

(sinking) inputs connect pin 9 to +V dc. The discrete I/O pins are 1, 5,

6, 8, 10, and 11.

10 Light Blue Discrete I/O #4 Input/Output

11 Black Discrete I/O #1 Input/Output

12 Violet RS-232 RX (receive) Input

Shield Bare metal Chassis ground -

VE Series Smart Camera

P/N 191667 Rev. J www.bannerengineering.com - Tel: + 1 888 373 6767 3

Wiring Diagrams

Figure 5. PNP Output

Output

Power

Supply

12–30 V dc

Output Common

VE Output

Load

Figure 6. NPN Output

12-30V dc

Output Common

VE Output

Load Output

Power

Supply

Figure 7. PNP Input

Input

Power

Supply

VE Input

Input Common

PNP Driver

12–30 V dc

Opto-isolator

Figure 8. NPN Input

Input Common

Input

Power

Supply

NPN Driver

VE Input

Opto-isolator

12–30 V dc

Install the Software

PC Requirements

Operating System

Microsoft®Windows®operating system version 7, 8, or 10 2

System Type

32-bit, 64-bit

Hard Drive Space

80 MB (plus up to 280 MB for Microsoft .NET 4.5, if not already installed)

Memory (RAM)

512 MB minimum, 1 GB+ recommended

Processor

1 GHz minimum, 2 GHz+ recommended

Screen Resolution

1024 × 768 full color minimum, 1650 × 1050 full color recommended

Third-Party Software

Microsoft .NET 4.5, PDF Viewer (such as Adobe Acrobat)

USB Port

USB 3.0, recommended if a USB to Ethernet adapter used to communicate with the

sensor

Important: Administrative rights are required to install the Vision Manager software.

1. Download the latest version of the software from www.bannerengineering.com.

2. Navigate to and open the downloaded ﬁle.

3. Click Next to begin the installation process.

4. Conﬁrm the software destination and availability for users and click Next.

5. Click Install to install the software.

6. Depending on your system settings, a popup window may appear prompting to allow Vision Manager to make changes to your computer.

Click Yes.

7. Click Close to exit the installer.

Getting Started

Power up the sensor, and verify that the power/error LED is ON green and that the Ethernet indicator is ON amber to verify the Ethernet

connection.

Connect to the Sensor

These instructions use Windows®operating system version 7, 8, or 10. 3

1. Conﬁrm the network connections.

a) Click the Start button, then on the Start menu, click Control Panel.

b) In Control Panel, click Network and Internet, then click Network and Sharing Center, and then click Change adapter settings.

c) Right-click on the connection that you want to change, then click Properties.

If you are prompted for an administrator password or conﬁrmation, enter the password or provide conﬁrmation.

d) In the connection properties, click Internet Protocol Version 4 (TCP/IPv4), and then click Properties.

e) In the Internet Protocol (TCP/IPv4) Properties, select Use the following IP address.

f) Make sure that the IP address is 192.168.0.2, and the subnet mask is 255.255.255.0.

2. Open Vision Manager from the desktop or the Start menu.

The Sensor Neighborhood tab displays and lists the available sensors.

2Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or other countries.

3Windows is a registered trademark of Microsoft Corporation in the United States and/or other countries.

VE Series Smart Camera

4 www.bannerengineering.com - Tel: + 1 888 373 6767 P/N 191667 Rev. J

3. From Sensor Neighborhood, click to connect to the desired sensor.

The status changes from Available to Connected and the Sensor screen displays. Click to disconnect from the sensor.

4. If the desired sensor is not listed, verify that:

• The network adapter connected to the sensor has the same subnet mask as the sensor (for example, 192.168.0.xxx); view the subnet

mask in the Network Adapters list at Home > Sensor Neighborhood > Network Adapters

• The Ethernet cable is the correct type

• The TCP/IPv4 settings are correct

Or, manually enter the sensor's IP address.

Note: The sensor's IP address and subnet mask are also available from the sensor display.

Sensor Screen

The Sensor screen displays the information needed to create or modify an inspection.

Figure 9. Sensor Screen

1. Screens—Home, Sensor, Inspection Logs, Inspection Management, System Settings

2. Manual Trigger button—Click to manually trigger the sensor

3. Inspection list—Select the desired inspection to start, and to view or modify the inspection

4. Summary pane—Includes the Inspection Summary, the I/O Summary, and the Test Summary

5. Parameters pane—Includes user-adjustable Inputs parameters or Test parameters for the tools in an inspection, depending on what is selected in the Tools and Results pane

6. Tools and Results pane—Includes Tools and Results, Tools Only, and All Results, which display the camera tool, the tools that are included in the current inspection, and the

results of the inspection

7. Image Pane Parameters panel—Includes ROI view buttons, zoom, x and y coordinates, grayscale value, settings button, and full image display button, as well as sensor

messages

8. Image pane—Displays the current image captured by the sensor; this includes the region of interest (ROI) for the tool for the selected inspection

Acquire a Good Image

The sensor needs to capture a good image of each part to ensure that it correctly passes good parts and fails bad parts.

1. Make sure that the lighting is appropriate for your target. Use supplementary lighting, such as a ring light, if necessary.

2. Click the Sensor screen.

3. Click the camera tool on Tools and Results.

The Inputs parameters display.

4. Set the trigger.

a) Expand the Trigger parameters.

VE Series Smart Camera

P/N 191667 Rev. J www.bannerengineering.com - Tel: + 1 888 373 6767 5

b) In the Trigger Mode list, click Internal (continuous images).

5. Run Auto Exposure.

a) Expand the Imager parameters.

b) Expand the Auto Exposure parameters, and click Start to run.

6. Check the lighting on the part.

• Make sure that the lighting is constant and consistent (unchanging over time, no shadows or hot spots)

• Capture the shape and form of the target object with lighting that optimizes its contrast and separates the feature of interest from the

background. Depending on the target, consider other Banner lights

• Adjust the mounting angle to provide the clearest image of the part features you are inspecting

7. After checking and adjusting the lighting, run Auto Exposure a second time or adjust the exposure manually by expanding the Exposure

parameters and moving the slider or entering a speciﬁc exposure time.

8. Adjust the focus.

a) Place the part so that the area to be focused appears in the center of the Image pane.

b) Expand the Focus Info parameters.

c) Make sure that the Focus Info checkbox is selected.

d) Adjust the focus of the lens while monitoring the focus number.

The focus number is a number between 1 and 255. Use the Image pane to determine when the image is sharp enough, or use the focus

number as a guide. Turn the focus ring on the lens until the focus number is at the highest possible number between 1 and 255. The

focus number is also available on the sensor display.

Note: There is no optimal value for this number, but it can be used as a guide if you are setting up more than one

sensor that are focused on the same target.

e) Tighten the locking thumbscrews to secure the lens at the desired focus.

Set Up an Inspection

Vision Manager allows you to set up or make changes to an inspection while the sensor is running. Changes are automatically saved as they are

made.

1. From the Sensor screen, click in the upper right corner to view the inspection list.

2. Click Add New Inspection.

A new inspection is added to the list, the Image pane updates, and the Tools & Results tab shows only the camera tool.

3. Add tools and adjust them as needed for the inspection.

Add a Tool

1. Click on the Tools & Results tab.

The Add Tool window opens.

2. Click the desired tool.

Note: Not all tools are available for all VE models, with the exception of Vision + ID models.

Tool Name Description

Available on:

Vision Models ID Models

Average Gray

Evaluates pixel brightness within an ROI and computes the average grayscale value. x

Bead

Inspects parts for uniformity of adhesive or sealant material, or for uniformity of a gap. x

Barcode

Finds and reads 1D and 2D barcodes. x

Blemish

Determines whether ﬂaws are present on a part, or detects whether a feature exists on a part. x

Blob

Detects and counts/locates groups of connected light or dark pixels within the ROI and

designates them as blobs (Binary Large Objects). After blobs are found, they can be

characterized by size and shape.

Circle Detect

Detects a single circle or piece of a circle (arc). x

Edge

Detects and counts transitions between bright and dark pixels (edges). Counts the total

number of edges, and determines the position of each edge.

Line Detect

Locates a single, straight line segment by ﬁnding edge points along bright or dark pixel

transitions and ﬁtting a line to those points.

Locate

Finds the ﬁrst edge on a part and compensates for translation and rotation of downstream

tools (if selected).

x x

Match

Veriﬁes that a pattern, shape, or part in any orientation matches a reference pattern. Can also

compensate for translation and rotation of downstream tools (if selected).

Object

Detects the edges of dark and bright segments and locates their midpoints. Counts dark and

bright segments, and measures the width of each dark and bright segment.

Math

Performs mathematical operations using tool data or user-supplied constants. Includes basic

arithmetic, inequality expressions, and statistical information.

x x

VE Series Smart Camera

6 www.bannerengineering.com - Tel: + 1 888 373 6767 P/N 191667 Rev. J

Tool Name Description

Available on:

Vision Models ID Models

Measure

Measures distance, calculates angles, and creates points and lines for use as inputs to other

tools.

Logic

Uses Boolean logic to combine or convert tool results, or to drive discrete outputs from tool

results. Logic tool data can be used to evaluate the results of a single tool or multiple tools.

x x

The tool is added to Tools & Results and the region of interest (ROI) appears on the Image pane.

3. Conﬁgure the tool as needed for your application.

a) Resize and rotate the ROI around the feature to be analyzed.

b) Deﬁne or view parameters for the tool on the Input tab, such as ROI shape, threshold, or view the histogram.

c) Deﬁne pass or fail criteria on the Test tab, such as the count, size, or match.

Save an Inspection to a Computer, Network Drive, or Storage Device

Vision Manager automatically saves inspections to the VE as they are created and modiﬁed. Save a copy of the inspection to your computer or

another network location if you want to be able to go back to previous settings.

Use the following procedure to save a copy of an inspection to your computer or a network location.

1. On the Inspection Management screen, click Transfer.

2. Change the destination folder, if desired.

a) Click above the right column.

An explorer window opens.

b) Navigate to the desired location, network location, or storage device.

c) Click Select Folder.

The folder is selected and the window closes.

The path to the location displays above the right column.

3. Select the desired inspection from the inspection list in the left column.

4. Click .

Inspection name.idb

displays in the right column and the inspection is transferred (saved) to the selected location.

Conﬁgure the Discrete I/O

From the System Settings screen, select Discrete I/O to change the discrete I/O settings.

Figure 10. Discrete I/O

For more details, see the Instruction Manual.

Sensor Display

The LCD display on the top of the sensor provides access to view or change several settings without using Vision Manager. The display provides

limited programming options:

•ETHER—Ethernet settings

•PCHANGE—Product change

•IO—Input/Output settings

VE Series Smart Camera

P/N 191667 Rev. J www.bannerengineering.com - Tel: + 1 888 373 6767 7

•IMAGE—Image settings

•INFO—Sensor information

•SYSERROR—System errors, if present

•DISPLAY—Display settings

•REBOOT—Reboot

Access the sensor menu by pressing Enter from the Home Screen on the sensor display.

Note that when User Proﬁles are enabled, the sensor display is available as read-only. No editing can be done directly from the sensor until User

Proﬁles are disabled for that sensor.

See the Instruction Manual, p/n 191666, for more information.

Sensor Display Interface

Down and Up Buttons

Press Down and Up to:

• Navigate the menu systems

• Change programming settings

When navigating the menu systems, the menu items loop.

Enter Button

Press Enter to:

• Access the Sensor Menu

• Access the submenus

• Save changes

In the Sensor Menu, a check mark in the lower right corner of the display indicates that pressing Enter accesses a submenu.

Escape Button

Press Escape to:

• Leave the current menu and return to the parent menu

• Leave the current menu and return to the Home Screen from any menu

Important: Pressing Escape discards any unsaved changes.

In the Sensor Menu, a return arrow in the upper left corner of the display indicates that pressing Escape returns to the parent

menu.

Press and hold Escape for 2 seconds to return to the Home Screen from any menu.

VE Series Smart Camera

8 www.bannerengineering.com - Tel: + 1 888 373 6767 P/N 191667 Rev. J

Sensor Menu

Figure 11. Menu Map

Enter Shortcuts Menu

Yes

100 HD

100 FD

FOCUS#

Home

Screen ETHER

PCHANGE

VE Series User Interface

Enter

Top Menu

IMAGE

INFO

Sub Menus

Go Back to Parent Menu

Select Menu Item

Press to Save Setting

Press and Hold to Go Back

to Home Screen

SPEED

LINK

SUBNET

GATEWAY

STATUS

PSELECT

TRIGGER

INPUT

MAC

MAX SPD

By NUM

OUTPUT

FW VER

BOOT

NAME

MODEL

HOUR

SERIAL

SLEEP

VIEW

Ethernet Menu

Product Change by Slot No.

Bit Representation of

Input/Output States

View Current

Focus No.

Sensor Info

(read-only)

DISPLAY

Display Settings

CLEAR

VIEW

SYSERR

System Error

Yes

REBOOT

Reboot Device

Return to Top

Yes

FOCUS#

TRIGGER 1000 FD

VE Series Smart Camera

P/N 191667 Rev. J www.bannerengineering.com - Tel: + 1 888 373 6767 9

Speciﬁcations

Power

12 V dc to 30 V dc (24 V dc ± 10% if a Banner light source is powered by the sensor)

Current: 400 mA maximum (exclusive of load and lights)

Use only with a suitable Class 2 power supply, or current limiting power supply rated

12 V DC to 30 V DC, 1 A

Supply Protection Circuitry

Protected against reverse polarity and transient overvoltages

Discrete I/O

1 Trigger IN

5 Programmable I/O

Output Conﬁguration

Optically isolated

Output Rating

Output Resistance: < 2 Ω

Strobe Output Resistance: < 13 Ω

Programmable Output: 100 mA

External Strobe Output: 100 mA

Off-State Leakage Current: < 100 µA

External Light Maximum Current Draw

350 mA

Exposure Time

0.01 ms to 500 ms

Memory

Device Settings and Inspection Storage Memory: 500 MB

Number of inspection ﬁles: 999

Acquisition

256 grayscale levels

Model Frames Per Second 4Image Size

VE200G1x 60 fps, maximum 752 × 480 px

VE201G1x 60 fps, maximum 1280 × 1024 px

VE202Gxx 50 fps, maximum 1600 × 1200 px

VE205G1x 22 fps, maximum 2592 × 2048 px

Torque—Tapped Holes for Mounting Screws

8 lbf·in (0.9 N·m) maximum torque

Construction

Housing: Aluminum

Display Label: Polyester

Connections

Ethernet: M12, 8-pin A-code or 4-pin D-code Euro-style female

Light Connector: M8, 3-pin Pico-style female

Power, Discrete I/O: M12, 12-pin Euro-style male

Imager

VE200G1x: 6.9 mm × 5.5 mm, 8.7 mm diagonal (1/1.8-inch CMOS)

VE201G1x: 6.9 mm × 5.5 mm, 8.7 mm diagonal (1/1.8-inch CMOS)

VE202Gxx: 7.2 mm × 5.4 mm, 9.0 mm diagonal (1/1.8-inch CMOS)

VE205G1x: 12.4 mm × 9.8 mm, 15.9 mm diagonal (1-inch CMOS)

Lens

C-mount

Pixel Size

VE200G1x: 5.3 µm

VE201G1x: 5.3 µm

VE202Gxx: 4.5 µm

VE205G1x: 4.8 µm

Communication

10/100/1000 5Mbps Ethernet

Communication Protocols

Ethernet/IP™, Modbus/TCP, PCCC, PROFINET®, TCP/IP, FTP, and RS-232

Environmental Rating

IEC IP67 with an optional sealed lens cover properly installed

Operating Conditions

Operating Temperature: 0 °C to +50 °C (+32 °F to +122 °F)

95% maximum relative humidity (non-condensing)

Stable Ambient Lighting: No large, quick changes in light level; no direct or reﬂected

sunlight

Storage Temperature: –30 °C to +70 °C (–22 °F to +158 °F)

Vibration and Mechanical Shock

Meets EN 60947-5-2: IEC 60068-2-27 (Shock: 30G); IEC 60068-2-6 (Vibration: 10 Hz

to 60 Hz, 1 mm amplitude)

Certiﬁcations

Information

Technology

Equipment

E365235

Banner Engineering Corp. Software Copyright Notice

This software is protected by copyright, trade secret, and other intellectual property laws. You are only granted the right to use the software and only for the purposes described by Banner. Banner reserves all

other rights in this software. For so long as you have obtained an authorized copy of this software directly from Banner, Banner grants you a limited, nonexclusive, nontransferable right and license to use this

software.

You agree not to use, nor permit any third party to use, this software or content in a manner that violates any applicable law, regulation or terms of use under this Agreement. You agree that you will not

reproduce, modify, copy, deconstruct, sell, trade or resell this software or make it available to any ﬁle-sharing or application hosting service.

Disclaimer of Warranties. Your use of this software is entirely at your own risk, except as described in this agreement. This software is provided "AS-IS." To the maximum extent permitted by applicable law,

Banner, it afﬁliates, and its channel partners disclaim all warranties, expressed or implied, including any warranty that the software is ﬁt for a particular purpose, title, merchantability, data loss, non-interference

with or non-infringement of any intellectual property rights, or the accuracy, reliability, quality or content in or linked to the services. Banner and its afﬁliates and channel partners do not warrant that the services

are secure, free from bugs, viruses, interruption, errors, theft or destruction. If the exclusions for implied warranties do not apply to you, any implied warranties are limited to 60 days from the date of ﬁrst use of

this software.

Limitation of Liability and Indemnity. Banner, its afﬁliates and channel partners are not liable for indirect, special, incidental, punitive or consequential damages, damages relating to corruption, security, loss or

theft of data, viruses, spyware, loss of business, revenue, proﬁts, or investment, or use of software or hardware that does not meet Banner minimum systems requirements. The above limitations apply even if

Banner and its afﬁliates and channel partners have been advised of the possibility of such damages. This Agreement sets forth the entire liability of Banner, its afﬁliates and your exclusive remedy with respect to

the software use. You agree to indemnify and hold Banner and its afﬁliates and channel partners harmless from any and all claims, liability and expenses, including reasonable attorney's fees and costs, arising

out of your use of the Services or breach of this Agreement (collectively referred to as "Claims"). Banner reserves the right at its sole discretion and at its own expense, to assume the exclusive defense and

control of any Claims. You agree to reasonably cooperate as requested by Banner in defense of any Claims.

Additional Copyright Information

Redistribution and use in source and binary forms, with or without modiﬁcation, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

3. All advertising materials mentioning features or use of this software must display the following acknowledgement: This product includes software developed by the University of California, Berkeley

and its contributors.

4. Neither the name of the University nor the names of its contributors may be used to endorse or promote products derived from this software without speciﬁc prior written permission.

THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,

SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS

INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT