Bausch Datacom Vega 56 PC2 Manuale utente
Vega 56 PC2 Users manual
07/06/1999 Bausch Datacom
1
Bausch Datacom nv/sa
Vega 56 PC2
Internal ISA-Voice/Fax Modem
Dual Standard V.90/K56Flex
Vega 56 PC2 Users manual
07/06/1999 Bausch Datacom
2
Users Manual
Vega 56 PC2 Users manual
07/06/1999 Bausch Datacom
3
Users Manual
1. Introduction
1.1 Modem caracteristics
2. Modem installation
3. Software installation
3.1 Windows 95/98 Driver Installation Procedure
3.1.1. Internal modem with Plug and Play setting enabled
3.1.1.1 If you have Windows 95 a
3.1.1.2 If you have Windows 95 b (or OSR2)
3.1.1.3 If you have Windows 98
3.1.2 Internal Modem with “Plug and Play” setting disabled
3.2 Modem Diagnostic in Windows 95/98
3.4 Installing Modem Drivers in Windows NT4.0
4. Trouble Shooting
Vega 56 PC2 Users manual
07/06/1999 Bausch Datacom
4
Appendix 1 Command Summary
Appendix 2 S-Register Summary
Appendix 3 Result Codes Summary
Vega 56 PC2 Users manual
07/06/1999 Bausch Datacom
5
1Introduction
You have chosen the Bausch Vega 56 PC2 modem to open the world of data
communication for your computer. By using this modems' advanced technology
and built-in quality, you can confidently communicate across town, across the
country, or even around the world via a fast 56.000 bps V.90 or K56Flex
connection to the Internet.
1.1 Modem caracteristics
Line Data Rate 56K/54K/52K/50K/48K/46K/44K/42K/40K/38K/36K/34K/*
33.6K/31.2K/28.8K/26.4K/24K/21.6K/19.2K/14.4K/12K/9.6K/
7.2K /14.8K/2.4K/1.2K/300/75bps
Modem Protocol ITU-T V.90, K56Flex, ITU-T V.34bis/ V.34/ V.32bis/
V.32/V.23/V.22bis/ V.22/ V.21
Voice Full-duplex speaker phone (optional)
Audio span (optional)
ASVD (optional)
Fax Compatibility 14400 bps send/receive, G3 compatible
Software Compatibility AT Command set compatible
Fax Command EIA Class 1 command compatible
Error Correction MNP 2-4 and V.42
Data Compression MNP 5 and V.42bis
Data Format
Serial, Binary, Asynchronous 7 or 8 data bits, odd, even or no
parity one or two binary serial synchronous stop bit, totally 10
bits length
DTE to Modem Data Rate
MAX. 115200bps
Operation Dial-Up
Data Interface ISA Bus compatible
Dialing Touch Tone
Audio Monitoring Mini speaker with programmable volume control
Line Interface RJ-11 modular jack
Vega 56 PC2 Users manual
07/06/1999 Bausch Datacom
6
2. Modem installation
?? See next page for internal modem jumper settings.
?? Remove the computer case and insert the modem card into a spare 16-bit
ISA expansion slot.
?? Close the case.
?? Insert the supplied phone cord into the line jack on the rear of the modem,
and the phone plug into the wall socket.
?? Proceed to Software installation.
Vega 56 PC2 Users manual
07/06/1999 Bausch Datacom
7
Vega 56 PC2 Users manual
07/06/1999 Bausch Datacom
8
Vega 56 PC2 Users manual
07/06/1999 Bausch Datacom
9
3. Software installation
3.1 Windows 95/98 Driver Installation Procedure
3.1.1 Internal modem with Plug and Play setting enabled
Turn on your computer and allow the system to boot to Windows 95. The modem
should be auto-detected by Windows 95/98 Plug and Play.
3.1.1.1 If you have Windows 95 a
(1) Insert the driver disk supplied with the modem into the Floppy or CD-ROM
drive and choose Driver from disk provided by hardware manufacturer.
Then click OK.
(2) Use Browse to select or fill in the drive letter of the Floppy or CD-ROM drive
(for example: A:\or D:\) and click OK.
Vega 56 PC2 Users manual
07/06/1999 Bausch Datacom
10
If you install from the
floppy, type “
A:
\
”
Vega 56 PC2 Users manual
07/06/1999 Bausch Datacom
11
(3) Select ‘Vega 56 PC2 internal’ and click OK.
3.1.1.2 If you have Windows 95 b (or OSR2)
(1) Click Next.
Vega 56 PC2 Users manual
07/06/1999 Bausch Datacom
12
(2) Windows will find the updated driver ‘Vega 56 PC2 internal’. Then click
Finish.
(3) Click Next.
Vega 56 PC2 Users manual
07/06/1999 Bausch Datacom
13
3.1.1.3 If you have Windows 98
(1) Click Next.
(2) Click Search for the best driver… Then click Next.
(3) Select Floppy disk drives or CD-ROM drive and click Next.
Vega 56 PC2 Users manual
07/06/1999 Bausch Datacom
14
(4) Windows will find the ‘Vega 56 PC2 internal’. Then click Next.
(5) Click Finish.
If you install from the
floppy, select
Vega 56 PC2 Users manual
07/06/1999 Bausch Datacom
15
Vega 56 PC2 Users manual
07/06/1999 Bausch Datacom
16
3.1.2. Internal Modem with “Plug and Play” setting disabled
A special procedure must be followed to install a Non Plug and Play internal
modem. Please check the Hardware installation to setup the jumpers for non
Plug and Play. If you want to set the modem in COM2/IRQ3, please disable the
BIOS of Serial port 2.
(1) Go to Start > Settings > Control Panel and double-click on the Add New
Hardware icon.
Vega 56 PC2 Users manual
07/06/1999 Bausch Datacom
17
(2)Click Next.
(3)Select Yes [Recommended] and click Next.
(4)Click Next.
Vega 56 PC2 Users manual
07/06/1999 Bausch Datacom
18
(5) Windows will take several minutes to detect the new hardware. When the
progress is finished, click Details to check the new hardware.
(6)Check to see if Windows detected the Communication Port. Click Finish.
Vega 56 PC2 Users manual
07/06/1999 Bausch Datacom
19
Vega 56 PC2 Users manual
07/06/1999 Bausch Datacom
20
(7) Go to Control Panel and double-click on the Modems icon.
(8)Select Don’t detect my modem; I will select it from a list and click Next.
Indice
Altri manuali Bausch Datacom Modem
Bausch Datacom
Bausch Datacom Proxima ISDN Lite Manuale utente
Bausch Datacom
Bausch Datacom DinBox Manuale utente
Bausch Datacom
Bausch Datacom DinBox GSM M4 Manuale utente
Bausch Datacom
Bausch Datacom DinBox RTU M4 Manuale utente
Bausch Datacom
Bausch Datacom InduBox PSTN III Foglio di istruzioni
Bausch Datacom
Bausch Datacom DinBox PSTN Manuale utente
Bausch Datacom
Bausch Datacom InduBox GSM M4 Foglio di istruzioni
