Baxall DVS24 Manuale utente

Issue 1 HBEMC/LVD -A-1 Issue 1 : 1/97

English

Please read this in conjunction with the

Installation Instructions

PRODUCT SAFETY AND ELECTROMAGNETIC

COMPATIBILITY (EMC)

This product is intended for use in general purpose CCTV

applications in a residential, commercial or light industrial

EMC environment.

Refer to your agent before installing or using the product in

medical and/or intrinsically safe applications or in an

industrial EMC environment.

WARNING : This is a Class A product. In a domestic

environment this product may cause radio interference in

which case the user may be required to take adequate

measures.

The product must be installed in accordance with good

installation practice to enable the product to function as

intended and to prevent problems. Refer to your agent for

installation guidance.

Contact your agent to obtain a specification defining the

acceptable levels of product degradation with regard to EMC

immunity.

MANUFACTURER’S DECLARATION OF

CONFORMANCE

The manufacturer declares that the product supplied with this

document is compliant with the essential protection

requirements of the EMC directive 89/336 and the Low

Voltage Directive LVD 73/23 EEC. Conforming to the

requirements of standards EN 55022 for emissions, IEC801

parts 2, 3 and 4 for immunity and BS415 superseded by

EN60950 for Electrical Equipment safety.

Français

Cette note doit être lue et jointe aux

instructions d'installation.

SECURITE ET COMPATIBILITE

ELECTROMAGNETIQUE

Ce produit est destiné à être utilisé pour les applications

générales de télévision en circuit fermé dans des

environnements résidentiels, commerciaux ou d'industries

légères à compatibilité électromagnétique.

Prendre conseil auprès du revendeur avant d'installer ou

utiliser le produit pour des applications médicales et/ou à

sécurité intrinsèque ou dans un environnement industriel dans

lesquels des précautions doivent être prises dans le domaine

des interférences radioélectriques.

ATTENTION : Ce produit est rangé en Classe A. Dans un

environnement domestique il peut provoquer des

interférences radioélectriques. Dans ce cas, l'utilisateur

pourra être amené à prendre des mesures appropriées.

L'installation doit se faire en respectant les règles de l’art afin

de permettre le bon fonctionnement du produit et empêcher

que d’éventuels problèmes surgissent. Pour obtenir des

conseils sur l'installation, s’adresser au revendeur.

Pour obtenir une spécification définissant les niveaux

acceptables de dégradation du produit en relation avec la

compatibilité électromagnétique, s’adresser au revendeur.

DECLARATION DE CONFORMITE PAR LE

FABRICANT

Le fabricant déclare que le produit fourni est conforme aux

prescriptions de la directive 89/336 sur la compatibilité

électromagnétique et de la directive LVD 73/23 sur la basse

tension. Il est également conforme aux normes EN 55022 sur

les émissions, IEC801 sections 2, 3 et 4 sur la compatibilité et

BS415 remplacée par la norme EN60950 relative à la

sécurité des équipements électriques.

Deutsch

Bitte zusammen mit den

Installationsanweisungen lesen.

PRODUKTSICHERHEIT UND

ELEKTROMAGNETISCHE VERTRÄGLICHKEIT

(EMV)

Dieses Produkt ist für den Einsatz in allgemeinen CCTV-

Anwendungen in Wohn-, Geschäfts- oder leichtindustriellen

Umgebungen ausgelegt.

Wenden Sie sich bitte an Ihre Vertretung, bevor Sie das

Produkt in medizinischen und/oder eigensicheren

Anwendungen oder in einer industriellen EMV-Umgebung

installieren.

WARNUNG : Dies ist ein Produkt der Klasse A. In einer

Wohnumgebung kann dieses Produkt Funkstörungen

verursachen; in diesem Fall wird der Benutzer

möglicherweise geeignete Maßnahmen ergreifen müssen.

Das Produkt muß gemäß guten Installationsverfahren

installiert werden, damit es vorschriftsmäßig funktionieren

kann, und um Probleme zu verhindern. Richtlinien für die

Installation erhalten Sie von Ihrer Vertretung.

Eine Spezifikation, die das akzeptable Ausmaß der

Produktdegradation hinsichtlich EMV-Störfestigkeit festlegt,

können Sie von Ihrer Vertretung anfordern.

KONFORMITÄTSERKLÄRUNG DES HERSTELLERS

Der Hersteller erklärt hiermit, daß das mit diesem Handbuch

gelieferte Produkt die grundlegenden Schutzanforderungen

der EMV-Vorschrift 89/336 und der

Niederspannungsverordnung LVD 73/23 EEC erfüllt.

Entspricht den Anforderungen der Normen EN 55022 für

Emissionen, IEC801, Teil 2, 3 und 4, für Störfestigkeit und

BS415, ersetz durch EN60950 für die Sicherheit von

Elektrogeräten.

Installation and Operating Instructions English

Dual Monitor Desk Video Switcher 1–10

Read these instructions first!

Manuel d’installation et d’utilisation Français

Console de commutation pour deux écrans 11 – 20

Veuillez lire ces instructions avant de commencer!

Installations- und Betriebsanweisungen Deutsch

Tisch-Videoumschalter mit zwei Monitoren 21 – 31

Bitte zuerst diese Anweisungen lesen!

DVS24

DVS28

BLANK

Page 2

English

For Safety

Please follow these instructions as you install your DVS2 and

have them available during the life-time of the DVS2. Ifyou have

any problems contact your supplier or telephone Baxall’s

Technical Support Department on +44 (0)161 406 6611.

WARNING: INSTALLATION IS ONLY TO BE CARRIED OUT BY

SUITABLY QUALIFIED AND EXPERIENCED

PERSONNEL

WARNING: ONLY USE THE DVS2 WITH THE CLASS 2 POWER

SUPPLY PROVIDED AND DO NOT ATTEMPT TO USE

THE POWER SUPPLY FOR ANY OTHER PURPOSE

The DVS2 is designed for use in general purpose CCTV

applications and must not be usedfor intrinsicallysafe or medical

applications.

Do not exceed the voltage and temperature limits given in the

specifications. Only use the DVS2 in a clean, dry, dust-free

environment.

Unpacking

Keep your packaging for use if your DVS2 is stored for a time or

needs to be returned for whatever reason. The packaging should

contain:-

»The switcher, either:- the DVS24 with 6 keys,

or the DVS28 with 10 keys.

»A mains-socket mounting +12V DC power supply (class 2)

»These instructions

If any of the items are missing or damaged then inform the

suppliers and carriers immediately, and do not attempt to use

your DVS2.

English

Page 3

The DVS2

Your DVS2 takes either 4 or 8 camera inputs which it switches to

two monitors. You can select cameras by pressing the relevant

numbered key. There is also an AUTO key which starts an

automaticsequenceonthecurrentmonitor.Thissequencedisplays

all the cameras in numerical order and automatically skips any

unused inputs.

You can sequence both monitors at the same time, with each

displaying its own sequence. The time spent on each camera in a

sequence is called the dwell-time, this can be varied from 1 to 60

seconds. On the main monitor you can change the dwell-time for

each camera separately, however on the spot monitor the same

dwell-time applies to all cameras in the sequence. This is called a

global dwell time.

You can also link the DVS28 to 8 alarm inputs (the DVS24 to 4)

by using it with the AL8. The available response options are

described later in these instructions.

Figure 1. A Typical switcher Arrangement (DVS28)

Page 4

English

Connecting your DVS2

Make all the video connections using 75ohm coaxial cable with

BNC connectors on each end.

When you are ready to connect your DVS2, refer to figure 2 and

follow the instructions given below:-

»Connect a cable from the connector labelled MAIN to your monitor

or VCR.

»Connect cables from the cameras to the numbered video-input

BNCs.

»Plug the jack-plug from the 12V DC power supply into the

jack-socket marked 12V DC.

»Plug the power supply into a suitable mains power outlet.

»Switch on the cameras, monitor and DVS2 (at the mains power

outlet).

Note: We have provided a supplementary earth terminal on the

rear panel, please ask Baxall Technical Support if you need

further information.

Switching On the Power

When you switch the power on, your DVS2 may start by

displaying a sequence or a single camera. If it cannot find any

camera inputs then it scans rapidly through the camera selection

LEDs but does not display a picture.

87654321MAIN SPOT ALARM 12V

Earth Terminal

Figure 2. Rear Panel Connections

English

Page 5

Operating Your DVS

To select a camera on the MAIN monitor ... simply press a

numbered key.

To select a camera on the SPOT monitor ... press and hold the

SPOT key and press a numbered key.

To start the sequence on the MAIN monitor ... press and release

<AUTO>.

To stop the sequence on the MAIN monitor ... press and release

a numbered key.

To start the sequence on the SPOT monitor ... press and hold

<SPOT> press and release <AUTO>.

To stop the sequence on the SPOT monitor ... press and hold

<SPOT> press and release a numbered key.

To set a dwell-time on the MAIN monitor ... select the camera

you want to change, press and hold <AUTO>. The dwell-time for

the current camera is displayed on the main monitor in seconds.

Use <1> to decrease the dwell-time and <2> to increase it, when

you are satisfied release <AUTO>.

Repeat this for all the cameras you need to change.

To set the global dwell-time on the SPOT monitor ... Press and

hold <SPOT> and <AUTO>. The dwell-time is displayed on the

main monitor in seconds.

Use <1> to decrease and <2> to increase the global dwell-time,

when you are satisfied release <AUTO> then <SPOT>.

NOTE: Switching off the power does not erase any settings.

To position the caption on the screen ... Remove the power plug

from the back of your DVS2. Press and hold <AUTO> and

re-insert the power plug.

Keep <AUTO> held throughout this procedure.

Page 6

English

The caption should now be displaying the model number and

software version.

Use <1> to move the caption up and <2> to move it down.

Press <4> and the display changes to the software date.

Use <1> to move the caption left and <2> to move it right.

Release <AUTO>.

To display the software version ... follow the instructions for

positioning a caption on the screen (above.)

ToRESETyourDVS2tofactorydefaults...Removethepower

plug from the back of your DVS2. Press and hold <AUTO> and

<SPOT> re-insert the power plug, wait for 3 seconds then release

<AUTO> and <SPOT>.

Using the DVS2 with Alarms

TheAL8has 8 alarminputs, itsfunction istotell theDVS2 which

of the alarms are active. The DVS2 assumes that

alarm 1 = camera 1, alarm 2 = camera 2 and so on. When only

one alarm is active the DVS2 shows the alarmed-camera on the

main monitor. If two or more alarms are active it can either:

•only display the most recent alarmed camera or,

•introduce the alarmed camera into a special sequence with a 2

second dwell-time.

Then, once the alarms are all cleared it can either:

•hold the last alarmed camera on the main monitor,

•start the normal sequence on the main monitor or,

•return to the settings it had before the first alarm.

A flashing LED indicates that the corresponding alarm is active

or has been active. Pressthe numbered key to cancel this once the

alarm is cleared.

English

Page 7

To Install the AL8

Firstly, follow the instructions supplied with the AL8, then set the

alarm options on your DVS2

To set the alarmoptions on the DVS2 ... Remove the power plug

from the backof your DVS2. Pressand hold <SPOT> and re-insert

the power plug. Press the numbered keys 1 to 3 to toggle the

options on and off (an asterisk represents on). The options are as

follows:-

Option 1 : start the normal sequence on the main monitor once all

the alarms are cleared.

Option 2 : return the MAIN monitor to its original settings once

all the alarms are cleared.

Option 3 : Sequence the active alarms on the MAIN monitor.

With Options 1 and 2 OFF : your DVS2 holds the last alarmed

camera on the main monitor.

Note: You cannot select both option 1 and option 2 together.

Page 8

English

Specifications

DVS24 : 4 video inputs, 2 video output (6 keys.)

DVS28 : 8 video inputs, 2 video output (10 keys.)

Video Signals

All video 1 V pk-pk composite video via 75ohm coaxial cable with BNC connectors.

Inputs AC coupled, maximum DC offset +/- 2.7 V

Main-Monitor Sequencing Operations

Sequences camera inputs in numerical order skipping unused inputs.

Dwell time is adjustable for each camera between 1 and 60 seconds

Spot-Monitor Sequencing Operations

Sequences camera inputs in numerical order skipping unused inputs.

Dwell time is globally adjustable between 1 and 60 seconds

Alarm Response Functions

Compatible with the Baxall AL8 alarm module the DVS2 has 3 options which apply to

the main monitor:

Option 1: Sequence the main monitor after alarms are cleared

Option 2: Return to previous state after alarms are cleared

Option 3: Sequence the current alarms on the main monitor

If no options are selected it displays the alarmed camera as it receives the alarms.

Power

Power Consumption: Maximum 2.4VA

Voltage range 12V DC +/-10%. Maximum 200mA

Power Supply Units:

230V AC +/-10% to +12V DC +/- 10% (class 2)

Dimensions

DVS24 : 181 x 88 x 36.5mm

DVS28 : 266 x 88 x 36.5mm

Weights

DVS24 : 0.4 kg

DVS28 : 0.6 kg

Material

ABS endcaps with aluminium and mild steel shell

Colour

Graphite-grey, blue lettering and keys

Temperature Specification

Operational temperature limits:-

-10ºC to +50ºC

at 10% to 80% relative humidity (non-condensing)

Storage temperature limits:-

-20ºC to +60ºC

at 10% to 95% relative humidity (non-condensing)

English

Page 9

Questo manuale è adatto per i seguenti modelli

Indice

Lingue:

Altri manuali Baxall Interruttore

Baxall

Baxall DVS14 Manuale utente

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente