BBV Tx1000 Manuale utente
Installation Guide
Tx1000
Tx1000 Matrix and Tx1000 Keypad
BBV
STOP AND READ
BEFORE INSTALLING!
As 3rd party protocols are not under the control of BBV,
we cannot guarantee that this unit will provide the exact
functionality required.
It is strongly recommended that operation is confirmed
during prebuild testing before installing on site.
Please contact our customer support department
if you have any questions/issues:
Tel: + 44 (0) 1323 842727
Email: support@bbvcctv.com
DISCLAIMER:
BBV are not liable for any errors within this manual. If you nd an error,
please let us know immediately.
Scan for a quick tour of the BBV website:
www.bbvcctv.com
Contents
Pre-Installation checks and procedures 6
Tx1000 Telemetry Transmitter – Introduction 7
Simple Tx1000 system 8
Technical Specification 9
Layout of the Tx1000 keypad 10 - 11
Disabling/Enabling the program key 12 - 13
Keypad Functions 14 - 18
RS422 Telemetry 19
Tx1000 Series Alarm Output 20 - 23
Self Test on the Keypad 23
BBV Product List 26 - 27
6
Pre-installation checks and safety procedures
Unpacking - Inspect the packaging for signs of damage. If damage has occurred, advise the carrier and/or the suppliers
immediately. Unpack the receiver carefully and check that all the items are present and correct (see checklist on box). If any
item is missing contact the supplier.
Important safety precautions
Read & Retain Instructions - All relevant safety, installation and operating instructions should be read & retained before
attempting to install, connect or operate the unit.
Water and Moisture - Do not expose the internal electronics of this unit to water or dampness.
Power Sources - This unit should be operated only from the supplied power supply.
Servicing - Servicing of the unit should only be undertaken by qualied service personnel.
Damage Requiring Service - Servicing by qualied personnel should be carried out under the following conditions:
(a) When the power-supply cord or plug is damaged;
(b) If liquid has been spilled, or objects have fallen into, the unit;
(c) If the internal electronics of the unit have been exposed to rain or water;
(d) If the unit does not operate normally by following the operating instructions.
(e) If the unit has been dropped or the enclosure is damaged;
Replacement Parts - If replacement parts are required, ensure that only replacement parts recommended by the product
manufacturer are used.
Safety Check - Upon completion of any service or repairs to the unit, safety checks should be performed to ensure that the
unit is in proper operating condition.
Coax Grounding - If an outside cable system is connected to the unit, be sure the cable system is grounded.
Pre-installation Checks - It is recommended that the unit be bench-tested prior to installation on the site.
Adhere to Safety Standards - All normal safety precautions as laid down by British Standards and the Health and Safety at
Work Act should be observed.
WARNING
To prevent danger of re or shock, do not expose the internal components of this equipment to rain or moisture.
Version Update Release Date
v10 Manual updates 25.9.18
Manual version history
7
Tx1000 Telemetry Transmitter – Introduction
Unpacking
The Tx1000 is a simple to use telemetry transmitter for multi-camera CCTV systems. They are easily installed into either a new
or an existing system.
Up-the-coax telemetry allows upgrading of static cameras to PTZ without the need for additional cabling.
BBV RS422 telemetry is available as standard where up-the-coax telemetry is not suitable or not required. An optional 20mA
twisted pair unit (Tx/MK2/TPO) can be retro-tted to the Tx1000 for complete compatibility with existing Tx1000 sites.
The transmitter is a two part design: the base unit, which is wall or rack mounting; and the keypad which is connected by a
video cable and a bi-directional RS232 link running at 9600 baud, No parity, 8 data bits and 1 stop bit.
Inspect the packaging for signs of damage. If damage has occurred, advise the carriers and/or the suppliers immediately.
Unpack the transmitter carefully and check all the items are included:
Part Number Description Tx1000 Keypad 2x mounting
brackets
4x M4
screws
PSU Manual Warranty
Card
Tx1000/16 Telemetry transmitter for
16 cameras with 2 monitor
outputs, with joystick KBD
XXX XXXX
8
Simple Tx1000 system
9
Technical Specification
Power Supply 12V dc 1000mA
Inputs Data input to base unit is RS232 via 9-pin D connector RS232 port allowing remote control from PC (9600, N, 8, 1)
Outputs BBV up the coax
BBV RS422
Features 2 keypads supported
2 monitor outputs
8 – 16 camera inputs
Up-the-coax & RS422 telemetry supported
Can be powered off 12V vehicle supply
Installation Base unit is 2U 19in rack mountable metalwork or wall mounted via the xing brackets supplied
Dimensions Width Depth Height Weight
Tx1000/KBD 370mm 220mm 120mm 1.05 kg
Base Units:
Tx1000/16 427mm 55mm 90mm 4 kg
10
Layout of the Tx1000 keypad
Installing the Tx1000 Matrix & Keypad
1. Mount the base unit on the wall or in a rack.
2. Connect the keypad to 9 pin D connector to the relevant keypad socket on
the Matrix:
Monitor 1 – Keypad 1
Monitor 2 – Keypad 2
3. Connect a BNC cable from output M1 to the keypad, and connect the other keypad
BNC to the video monitor’s video input. Make sure that the monitor is terminated,
not Hi-Z.
4. If the keypad is remotely sited from the base unit, connect the 12Vdc plug
mounted power supply to the keypad via the 2.1mm power connector.
5. Connect either a second video monitor, or the second keypad to Output 2. Note
that even if both keypads are local to the main unit, the second keypad must be
powered from its own 12Vdc power supply.
6. Connect the BNC cables from the cameras/receivers to the upper BNC sockets in
each row, marked “VIDEO IN”.
7. Connect any other equipment requiring the camera video signals to the lower BNC
sockets marked “LOOP OUT”. Note that the action of connecting to the video out
socket removes the 75* termination.
8. If the user relay terminals are being used, connect these to the LOW VOLTAGE
equipment of your choice.
PIN 6 Normally closed
PIN 7 Common
PIN 8 Normally open
9. Plug in the Matrix 12Vdc power supply.
Altri manuali per Tx1000
2
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali BBV Trasmettitore
