BEC MX-221P Manuale utente

BEC MX-221P

Triple-SIM 4G/LTE Router

Quick Start Guide

BEC MX-221P Triple-SIM 4G/LTE Router

Package Contents

✓BEC MX-221P 4G/LTE Router * 1

✓This Quick Start Guide * 1

✓RJ-45 Ethernet Cable * 1

✓4G/LTE Antenna * 2

✓DC Power Adapter * 1

NOTE:ALL IMAGES SHOWN ARE FOR ILLUSTRATION PURPOSE ONLY.

PACKAGE CONTENTS MAY DIFFER FROM ACTUAL PRODUCTS.

Warning

⚫Do not use the router in high humidity or at high temperature.

⚫Do not use the same power source for the router as other equipment.

⚫Do not open or repair the case yourself. If the router is too hot, turn off

the power immediately and have it repaired at a qualified service center.

⚫Avoid using this product and all accessories outdoors.

Attention

⚫Place the router on a stable surface.

⚫Only use the power adapter that comes with the package. Using a

different voltage rating power adapter may damage the router.

PLEASE READ THE QUICK START GUIDE AND FOLLOW THE

STEPS CAREFULLY. THIS QUICK START GUIDE WILL HELP YOU

INSTALL THE DEVICE PROPERLY AND AVOID IMPROPER USAGE.

IF YOU NEED MORE INFORMATION ON THIS SOFTWARE

CONFIGURATION, PLEASE REFER TO THE ONLINE USER

MANUAL.

Quick Start Guide

Front Panel LEDs

LED

STATUS

DESCRIPTION

Power

Green

System is up and ready

Red

Boot failure

Ethernet Port

LAN 1 - 2

Green

Transmission speed is at Gigabit speed (1000Mbps)

Orange

Transmission speed is at 10/100Mbps

Blinking

Data being transmitted/received

LTE

(Received Signal

Strength

Indicator)

Green

RSSI greater than -69 dBm. Excellent signal condition

Green

Flashing

quickly

RSSI from -81 to -69 dBm. Good signal condition

Orange

Flashing

quickly

RSSI from -99 to -81 dBm. Fair signal condition

Orange

Flashing

slowly

RSSI less than -99 dBm. Poor signal condition

Orange

No signal. The cellular module is in service

Off

No LTE module or LTE module fails

Green &

Orange

MX-221P is either in debug mode or in upgrading firmware process

Internet

Green

IP address has received, and traffic is passing thru the device

Red

IP address request has failed

Off

MX-221P is either in bridged mode or WAN connection is not ready

BEC MX-221P Triple-SIM 4G/LTE Router

Rear Panel Connectors

INTERFACE

MEANING

4G/LTE Antenna

Connectors

(Main/Aux)

SMA female connectors.

Manually screw the cellular antennas tight to the female connectors

Connect to Main if decide to use single antenna instead of two

Power Source

Power ON/OFF switch

(1) Power Switch ON: if want to power up by the supplied DC power adapter

(2) Power Switch OFF: if want to power up by a PoE injector

Power Jack

(DC IN)

Connect the supplied Power Adapter to this jack

RESET

After the device is powered on, press it 6 seconds or above: to restore to factory

default settings (this is used when you cannot login to the router, e.g. forgot your

password)

Gigabit Ethernet

(LAN 1 / PoE)

Ethernet LAN: Connect to a 10/100/1000Mbps Ethernet device

Ethernet PoE:Connect to an 802.3at Gb PoE injector to provide power to the

MX-221P.

Gigabit Ethernet

(LAN 2 / WAN)

Ethernet LAN: Connect to a 10/100/1000Mbps Ethernet device

Ethernet WAN: Software configurable in the GUI. Connect to a broadband device

such as a cable modem, ADSL/VDSL modem or fiber modem

SIM Card Slots

SIM 1 : Insert the mini SIM card (2FF) with the gold contact facing down

SIM 2 : Insert the mini SIM card (2FF) with the gold contact facing up

SIM 3 : Insert the mini SIM card (2FF) with the gold contact facing down

Push the mini SIM card (2FF) inwards to eject it

* Power off the MX-221P before inserting or removing the SIM card(s)

Quick Start Guide

Application Diagrams

I. WAN: 4G/LTE | Power Source: DC Power (ON) | LAN: Ethernet Devices

II. WAN: 4G/LTE | Power Source: PoE Injector (OFF).

LAN1: Connect to the PoE injector | LAN2: Ethernet Device (notebook, switch, etc.)

III. WAN: Ethernet WAN (LAN2) |Power Source: DC Power Adapter (ON).

LAN1: Ethernet Device (notebook, switch, etc.) | LAN2: Wireline Modem

BEC MX-221P Triple-SIM 4G/LTE Router

Hardware Installation

1. Power Connection

Select power source from using a (1) DC power adapter or (2) PoE Injector

1.1 Using the Supplied DC Power Adapter

Plug in the supplied power adapter to the wall jack, the other side to the MX-221P then

power it ON the by pressing the Power On/Off button.

1.2 Using a PoE Injector

Power OFF the power source button then plug an Ethernet cable (RJ-45) to the

LAN 1/PoE IN port and the other end of the cable directly to the Data+Power of a PoE

injector.

Quick Start Guide

2. LAN Connection

Plug the RJ-45 Ethernet cable to one of the Ethernet ports, and the other side to the PC’s

Ethernet interface.

3. WAN Link Interface and Connection

BEC MX-221P supports failover and failback to another WAN interface, 4G/LTE or Ethernet

WAN. <Please refer to user manual for detailed setup>

3.1 Mobile 4G/LTE Connection

Slide SIM card(s) into SIM tray starting with (default) SIM1 / SIM2 / SIM3. Make sure that the

SIM card is inserted correctly and slid into the bottom of the slot with a click sound. When

removing the SIM card, press the SIM card again it will be ejected from the card slot.

SIM 1 & SIM 3: Gold part of the SIM faces down on the tray.

SIM 2: Gold part of the SIM faces up on the tray.

WARNING: Please power off the device before inserting or removing the SIM

card.

BEC MX-221P Triple-SIM 4G/LTE Router

3.2 Ethernet WAN Connection

Connect RJ-45 Ethernet cable to the WAN port and connect the other side to another

alternative broadband device, such as Cable Modem, VDSL, Fiber Modem, or PON optic line.

Quick Start Guide

Access and Configure Your BEC MX-221P

The default IP of modem is 192.168.1.254 with subnet 255.255.255.0. Make sure the attached

PC to this router is in the same subnet and has an IP address in the range between 192.168.1.1

~ 192.168.1.253.

Open a web browser and type http://192.168.1.254 in the URL address bar.

The login prompt will appear. Input the default username and password.

*This username / password may vary by different Internet Service Providers.

Quick Setup Your Router

Use the Quick Start for fast connection setup.

Step 1: Change administration password

Setup a new password for “admin” account for device management. The default password is

“admin”. Click Continue to go on to the next step.

*The password may vary by different Internet Service Providers.

Step 2: Time Zone configuration

Enable and select your Time Zone then click Continue to go on to the next step.

URL Address bar: type

http://192.168.1.254

Time Zone: select your time zone

Next Step: click Next

Wired Broadband Connection - before start configuring the MX-221P, make sure you

have the LAN2/WAN connect to your Internet box or fiber line.

New Password: assign a new,

unique password

Confirm Password: re-enter the

new password again

Next Step: click Next

Indice

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

Cisco

Cisco NCS 540 Manuale

XAVi

XAVi X8821e Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

Cisco

Cisco ASR 1000 Series Manuale dell'operatore

EnGenius

EnGenius ESR-9710 Manuale utente

Cisco

Cisco 805 Series Istruzioni operative e di sicurezza

LevelOne

LevelOne FBR-1416 Manuale utente