BEC V8E2G Manuale utente

-1-

BEC V8E2G

8-Port VDSL2 + 2 Gigabit Combo

VDSL2 30a CO Switch

User Manual

-2-

The information in this guide may be changed without notice. The

manufacturer assumes no responsibility for any errors which may appear in

this guide.

Ethernet is a trademark of XEROX Corporation. Microsoft, Windows and

Windows logo are trademarks of Microsoft Corporation.

maybe transmitted or reproduced in any form or by any means without the

written permission of BEC Technologies, Inc..

The revision date for this guide is Jan. 2010,

Version 1.0I

FCC Statement

This product has been tested and found to comply with the limits for a Class A

digital device pursuant to Part 15 of FCC Rules. These limits are designed to

provide reasonable protection against such interference when operating in a

commercial environment. This equipment generates uses and can radiate

radio frequency energy, and if not installed and used according to the

instructions, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause interference,

in which the case user, at his or her own expense will be required to take

whatever measures to correct the interference.

CE Mark Warning

This is a Class A product. In a domestic environment, this product may cause

radio interference in which case the user may be required to take adequate

measures.

-3-

Contents

1. Introduction................................................................................................4

1.1. Package Contents............................................................................4

1.2. How to Use this Guide .....................................................................4

2. Installation..................................................................................................5

2.1. Product Description Overview..........................................................5

2.2. Switch Front and Rear Panel ...........................................................5

2.3. LED Function ...................................................................................6

2.4. Installing the Switch .........................................................................6

2.4.1. Pre-Installation Considerations............................................7

2.4.2. Desktop or Shelf Mounting ..................................................7

2.5. Rack- Mount Placement...................................................................7

3. Configuration .............................................................................................9

3.1. Login ................................................................................................9

3.1.1. Power-On Self-Testing ........................................................9

3.1.2. Console Login .....................................................................9

3.1.3. Login with a Web Browser...................................................9

3.2. Web User Interface ........................................................................10

3.2.1. Home.................................................................................10

3.2.2. Administration....................................................................10

3.2.3. L2 Features .......................................................................23

3.2.4. Access Control List............................................................41

3.2.5. Security .............................................................................46

3.2.6. QoS ...................................................................................49

3.2.7. Monitoring..........................................................................50

3.2.8. Profile configuration...........................................................51

3.2.9. Reset System ....................................................................53

3.2.10. Reboot...............................................................................53

4. Specifications ..........................................................................................54

4.1. Cable specifications .......................................................................54

4.2. Technical Specifications ................................................................56

4.2.1. Software Specification.......................................................56

4.2.2. Hardware specification ......................................................57

4.3. Environments Specification............................................................58

4.4. Standard Conformance..................................................................58

5. Warranty statement .................................................................................59

6. Product Support & Contact.....................................................................59

-4-

1. Introduction

Thank you for choosingVDSL2 Product

These products are cost-effective

switching solution idea for small business and the network edge. It provides

the Quality of Service (QoS) features, like 802.1p, DSCP and Rate Control etc,

to ensure the traffic is prioritized properly to deliver real-time applications like

voice and video and also have a good control in network bandwidth usage.

The 802.1Q feature enables you separate the network traffic easily and quickly.

The Network Security features, like ACL, Port Security, Storm Control, 802.1X

and Management IP List etc, enables you to prevent unauthorized access to

company network and block intentional or inadvertent network traffic. The

Spanning Tree Protocol (STP) provides you a loop-free network. The IGMP

snooping enables you to have efficient network usage in IP multicast

environment. The one-to-one or many-to-one Port Mirroring feature of the

switch enables you to monitor the traffic on the network. With these features,

you can build or expand your network quickly and easily.

1.1.Package Contents

The package contains the following:

> One VDSL2 Switch

> One RS-232 cable

> One power cord/adapter

> One set of brackets.

> One CD for user manual and utilities.

If any of the listed items is missing or damaged, please contact the place of

purchase.

1.2. How to Use this Guide

This user guide is structured as follows:

Chapter 2, Installation explains the functions of the switch and how to

physically install it.

Chapter 3, Configuration explains how to set up and modify the configuration

of the switch.

Chapter 4, Specifications contains information about the cables, and the

technical specifications of the switch.

Appendices include the Warranty Statement. Read them as necessary.

-5-

2. Installation

This chapter describes the function of the VDSL2 switch components and

shows how to install it on the desktop or shelf. Basic knowledge of networking

is assumed. Read this chapter completely before continuing.

2.1.Product Description Overview

The product support VDSL2,

supports 802.1Q VLAN, QoS, 802.1d / 1w/ 1s

Spanning Tree Protocol, 802.1x, Port Security, Port Mirroring, IGMP Snooping,

SNTP, Storm Control, Rate Control, SNMP and RMON, Link Aggregation

(IEEE 802.3ad)

etc. features.

2.2. Switch Front and Rear Panel

The front panel of 8-Port VDSL2 + 2 Gigabit Combo VDSL2 30a CO Switch

has 8 VDSL2 ports at the left, 2 Gigabit SFP slots and two 2 Gigabit copper

ports at the right. The product name is at the top on the left. Figure 2.2.2a

shows a front panel of this switch.

The rear panel has a power connector, and figure 2.2.2b shows a rear panel of

the switch.

Table 2.2.2c shows the port function of the switch.

Figure 2.2.2a Front Panel

Figure 2.2.2b Rear Panel

Table 2.2.2c Port Function

Port Function

VDSL2 Connect to VDSL2 interface.

RJ45 These 2 RJ-45 ports connect to network devices such as PCs,

print servers and other network peripherals at 1000 Mbps.

SFP These 2 mini GBIC ports allows you to insert a SFP module for

1000Mbps fiber connection

Console

This is where you will connect RS232 console cable.

Power This is where you will connect the AC power adapter.

-6-

2.3. LED Function

This section explains the definition of the Switch’s LEDs on the front panel.

Group LED Color Function

System

Green

On : When the power supplied to the system

Off : Power off

Blinking: While system Booting /System

Self-Test / Firmware upgrade/Error.

VDSL port

Link/Act

Green

Lights: When the link through the port is

successfully established.

Off : No-link detected for the port

Blinks: When the port is activating

transmitting data.

Link/Act

Green

Lights: When the link through the port is

successfully established.

Off: for no-link detected for the port

Blinks: When the port is activating

transmitting data.

GE-LED

G1/G2

Speed

Amber

Lights: Link at 1000Mbps

Off: Link at 100/10Mbps or No Link

2.4. Installing the Switch

This section describes how to install and make connection to your VDSL2

Switch. The following diagrams shows the typical network configuration,

Read and perform the following procedures to install the switch,

-7-

2.4.1.Pre-Installation Considerations

Gigabit Considerations:

If you will use the switch for Gigabit applications, keep in mind that the

maximum UTP cabling length of Category 5e cable is 328 feet (100 meters).

Positioning the switch:

When choosing a location for the switch, observe the following guidelines:

Keep enough ventilation space between the switch and the surrounding

objects.

Keep cabling away from sources of electrical noise, power lines, and

fluorescent lighting fixtures.

Do not stack free-standing switch more than four units high.

2.4.2.Desktop or Shelf Mounting

To install the switch on a desktop or shelf, simply complete the following steps:

Step 1 Place the switch on a desktop or shelf near an AC power source.

Step 2 Keep enough ventilation space between the switch and the surrounding

objects.

Note: When choosing a location, keep in mind the environmental restrictions

discussed in Chapter 4, Specifications.

Step 3 Connect the switch to network devices.

A. Connect one end of a standard network cable to the RJ11/RJ-45

ports on the front of the switch.

B. Connect the other end of the cable to the network devices such as

printer servers, VoIP, Video, workstations or routers.

Step 4 Supply power to the switch.

A. Connect one end of the power cable to the switch.

B. Connect the power cube end of the power cable to a standard wall

outlet.

2.5. Rack- Mount Placement

Before mounting the Switch, please read the following instructions carefully,

A) Elevated Operating Ambient - If installed in a closed or multi-unit rack

assembly, the operating ambient temperature of the rack environment may be

greater than room ambient. Therefore, consideration should be given to

installing the equipment in an environment compatible with the maximum

ambient temperature (Tma) specified by the manufacturer.

B) Reduced Air Flow - Installation of the equipment in a rack should be such

that the amount of air flow required for safe operation of the equipment is not

compromised.

C) Mechanical Loading - Mounting of the equipment in the rack should be

such that a hazardous condition is not achieved due to uneven mechanical

D) Circuit Overloading - Consideration should be given to the connection of

the equipment to the supply circuit and the effect that overloading of the

circuits might have on over current protection and supply wiring. Appropriate

consideration of equipment nameplate ratings should be used when

addressing this concern.

-8-

E) Reliable Earthing - Reliable earthing of rack-mounted equipment should

be maintained. Particular attention should be given to supply connections

other than direct connections to the branch circuit (e.g. use of power strips)."

To mount the Switch in any standard-sized, 19-inch wide, 1U high rack, please

follow these instructions:

Place the Switch on a hard flat surface with the front panel facing you.

Attach a rack–mount bracket to one side of the Switch with the supplied

screws. Then attach the other bracket to the other side. (Figure 2.5.1)

Figure 2.5.1

Make sure the brackets are properly attached to the Switch.

Use the appropriate screws (not included) to securely attach the brackets to

your rack. (Figure 2.5.2)

Figure 2.5.2

-9-

3. Configuration

3.1.Login

3.1.1.Power-On Self-Testing

The power-on self-testing is running immediately after the switch system is

powered up. The self-testing program diagnoses the hardware components of

a switch system. After hardware tests are all passed, the system will detect

and display the module slot status and start the initializations. The system will

be in ready state while the prompt is showing up.

3.1.2.Console Login

When you connect to the switch with a terminal emulation program, refer to the

information of: Baurate (bits/sec) 115200; Data Bits 8

，

Parity Check none ;Stop

Bits 1. Type “cli” if you want to log in the configuration of the switch .Enter a

user name and password to login to access the switch. The default user name

is “admin” and the password is empty.

3.1.3.Login with a Web Browser

When you connect to the switch through a web browser, a login screen is

displayed. Enter a user name and password to login to access the switch.

-10-

Items Option Default Value

User name Max:10, Min:0 characters, case sensitive admin

Password Max:10, Min:0 characters, case sensitive NULL

3.2. Web User Interface

3.2.1.Home

After user login verification, the homepage of the switch will be shown as

below.

3.2.2.Administration

There are many management functions can be set or performed if you expand

the submenus of Administrator in MENU area. These functions are:

IP Address

Switch Setting

Console Port Info

Port Configuration

SNMP Configuration

Indice

Altri manuali BEC Interruttore

BEC

BEC ES08 Manuale utente

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente