BEC MX-241NP Manuale utente

Quick Start Guide

Model |

MX-241NP

Product |

4G LTE CBRS Wi-Fi Router

teamsupport@bectechnologies.net | +1 972-422-0877 Ext. 2

www.bectechnologies.net

BEC MX-241NP 4G/LTE CBRS Wi-Fi Router

| 1

l BEC MX-241NP X 1

l Quick Start Guide X 1

l RJ-45 Ethernet Cable X 1

l 4G/LTE Antenna X 2

l DC Power Adapter X 1

Warning

l Do not use the router in high humidity or at high temperature.

l Do not use the same power source for the router as other equipment.

l Do not open or repair the case yourself. If the router is too hot, turn off the

power immediately and have it repaired at a qualified service center.

l Avoid using this product and all accessories outdoors.

Attention

l Place the router on a stable surface.

l Only use the power adapter that comes with the package. Using a different

voltage rating power adapter may damage the router.

PLEASE READ THE QUICK START GUIDE AND FOLLOW THE STEPS

CAREFULLY. THIS QUICK START GUIDE WILL HELP YOU INSTALL

THE DEVICE PROPERLY AND AVOID IMPROPER USAGE. IF YOU

NEED MORE INFORMATION ON THIS SOFTWARE CONFIGURATION,

PLEASE REFER TO THE ONLINE USER MANUAL.

Package Contents

NOTE:

ALL IMAGES SHOWN ARE FOR ILLUSTRATION PURPOSE ONLY.

PACKAGE CONTENTS MAY DIFFER FROM ACTUAL PRODUCTS.

BEC MX-241NP 4G/LTE CBRS Wi-Fi Router

| 2

LED

STATUS

DESCRIPTION

Power

Green

System is up and ready

Red

Boot failure

Ethernet Port LAN

1 - 2

Green

Transmission speed is at Gigabit speed (1000Mbps)

Orange

Transmission speed is at 10/100Mbps

Blinking

Data being transmitted/received

Wireless

Green

Wireless connection established

Green blinking

Data being transmitted / received

Orange

WPS configuration is in progress

LTE

(Received Signal

Strength Indicator)

Green

RSSI greater than -69 dBm. Excellent signal condition

Green Flashing quickly

RSSI from -81 to -69 dBm. Good signal condition

Orange Flashing quickly

RSSI from -99 to -81 dBm. Fair signal condition.

Orange Flashing slowly

RSSI less than -99 dBm. Poor signal condition.

Orange

No signal and the cellular module is in service

Off

No LTE module or LTE module fails

Green & Orange

MX-241NP is either in debug mode or in upgrading

firmware process

Internet

Green

IP address has received; traffic is passing thru the device.

Red

IP address request has failed.

Off

MX-241NP is either in bridged mode or WAN connection

not ready.

Front Panel LEDs

BEC MX-241NP 4G/LTE CBRS Wi-Fi Router

| 3

Reset

Gigabit Ethernet

2/EWAN 1 / PoE IN

MAIN DIV/AUX

PoE

DC IN

SIM

01 01

0506

INTERFACE

MEANING

4G/LTE Antenna Connectors

(Main/Aux)

SMA female connectors.

Manually screw the cellular antennas tight to the female connectors.

Connect to Main if decide to use single antenna instead of two.

Power Source

Power ON/OFF switch

(1) with Power Switch ON: power up by the supplied DC power adapter

(2) with Power Switch OFF: power up by the PoE Injector unit

Power Jack (DC IN)

Connect the supplied Power Adapter to this jack.

Reset

After the device is powered on, press it 6 seconds or above: to restore to

factory default settings (this is used when you cannot login to the router,

e.g. forgot your password)

Gigabit Ethernet

(LAN 1 / PoE)

Ethernet LAN: Connected to a 10/100/1000Mbps Ethernet device

Ethernet PoE: Connect to an 802.3at Gb PoE injector to provide power to

the MX-241NP

Gigabit Ethernet

(LAN 2 / EWAN)

Ethernet LAN: Connected to a 10/100/1000Mbps Ethernet device

Ethernet WAN: Software configurable in the GUI. Connect to a

broadband device such as a cable modem, ADSL/VDSL modem or fiber

modem.

SIM Card Slot

Insert the mini SIM card (2FF) with the gold contact facing down.

Push the mini-SIM card (2FF) inwards to eject it

* Power off the MX-241NP before inserting or removing the SIM card(s)

Rear Panel Connectors

BEC MX-241NP 4G/LTE CBRS Wi-Fi Router

| 4

I. WAN: 4G/LTE | Power Source: DC Power (ON) | LAN: Ethernet Devices

II. WAN: 4G/LTE | Power Source: PoE Injector (OFF).

LAN1: Connect to the PoE injector | LAN2: Ethernet Device (notebook, switch, etc.)

Hardware Connection

BEC MX-241NP 4G/LTE CBRS Wi-Fi Router

| 5

III. WAN: Ethernet WAN (LAN2) | Power Source: DC Power Adapter (ON).

LAN1: Ethernet Device (notebook, switch, etc.) | LAN2: Wireline Modem

1. Power Connection

Select power source from using a (1) DC power adapter or (2) PoE Injector

1.1 Using the Supplied DC Power Adapter

Plug in the supplied power adapter to the wall jack, the other side to the MX-241NP then

power it ON the by pressing the Power On/Off button.

Hardware Installation

BEC MX-241NP 4G/LTE CBRS Wi-Fi Router

| 6

1.2 Using a PoE Injector

Power OFF the power source button then plug an Ethernet cable (RJ-45) to the LAN

1/PoE IN port and the other end of the cable directly to the Data+Power of the PoE

injector.

2. LAN Connection

Plug the RJ-45 Ethernet cable to one of the Ethernet ports, and the other side to the PC’s

Ethernet interface.

BEC MX-241NP 4G/LTE CBRS Wi-Fi Router

| 7

3. WAN Link Interface and Connection

BEC MX-241NP supports failover and failback on dual WAN interfaces, 4G/LTE and ETH

WAN. <Please refer to User Manual for detailed Internet setup>

3.1 Mobile 4G/LTE Connection

Slide the SIM card into the card slot of the device with the gold contact facing down. Make

sure that the SIM card has been slid into the bottom of the slot with a click. When removing

the SIM card, press the SIM card again it will be ejected from the card slot.

3.2 Ethernet WAN Connection

Connect RJ-45 Ethernet cable to the EWAN port, and connect the other side to another

alternative broadband device, such as Cable Modem, VDSL, Fiber Modem or PON optic

lines.

WARNING: Please power off the device before inserting or removing the SIM card.

BEC MX-241NP 4G/LTE CBRS Wi-Fi Router

| 8

The default IP of modem is 192.168.1.254 with subnet 255.255.255.0. Make sure the attached

PC to this router is in the same subnet and has an IP address in the range between 192.168.1.1

~ 192.168.1.253.

Open a web browser and type http://192.168.1.254 in the URL address bar.

The login prompt will appear. Input the default username and password.

*This username / password may vary by different Internet Service Providers.

Use the Quick Start for fast connection setup.

Step 1: Change administration password

Setup a new password for “admin” account for device management. The default password is

“admin”. Click Continue to go on to the next step.

*The password may vary by different Internet Service Providers.

Step 2: Time Zone configuration

Enable and select your Time Zone then click Continue to go on to the next step.

URL Address bar: type

http://192.168.1.254

Time Zone: select your time zone

Next Step: click Next

Wired Broadband Connection - before start configuring the MX-241NP, make sure

you have the LAN2/EWAN port connect to your Internet box or fiber line.

New Password: assign a new,

unique password

Confirm Password: re-enter

the new password again

Next Step: click Next

Connecting to the Router

Quick Setup Your Router

BEC MX-241NP 4G/LTE CBRS Wi-Fi Router

| 9

Step 3: Setup Wireless Connection

Step 4: WAN / Internet Connection Setup

Select the appropriate WAN protocol then fill out the information provided by your ISP in all

relevant parameters.

4.1 WAN Interface: 4G/LTE

Access Point: select Activated

SSID: Assign a unique name

Channel: pick from 1~11

Security Type: select a mode

- Disable (No security)

- WPA

- WPA2 (Most secure one)

- WPA / WPA2 (auto detect WPA mode with

wireless clients)

- WEP (Less secure one)

Pre-Shared Key: key for wireless

authentication

- WPA / WAPA2 Share Key: Assign a key

between 8 ~ 63 characters.

- WEP: select Open System, use default

WEP Key 1 then assign 26 Hex codes

Next Step: click Next

Indice

Manuali Router wireless popolari di altre marche

Milesight

Milesight UG67 Manuale utente

Airlogic

Airlogic AirSync Class 1 Manuale del proprietario

Samsung

Samsung WCH730B Manuale utente

TELEFONICA

TELEFONICA USB Adapter Manuale utente

NETGEAR

NETGEAR PowerLINE WiFi 1000 Series Manuale utente

Askey

Askey RAC2V1K Manuale utente

Alloy

Alloy WLF2454AP-S Manuale utente

TP-Link

TP-Link TL-WR542G Manuale utente

NETGEAR

NETGEAR WNR2000v4 Manuale utente

Hama

Hama 53120 Manuale utente

Intellinet

Intellinet 524582 Manuale utente

Asus

Asus RT-N10P Manuale utente

D-Link

D-Link DIR-506L Manuale utente

Sapido

Sapido GR297n Manuale utente

Asus

Asus DSL-N55U Manuale utente

AMTC

AMTC WR7502 Manuale utente

Compaq

Compaq CP-2W - iPAQ Connection Point Manuale utente

SMC Networks

SMC Networks WBR14-N2 FICHE Manuale utente