Behringer MS-1-BK Manuale
Synthesizers and Samplers
MS-1-BK /
MS-1-BU / MS-1-RD
Analog Synthesizer with 32 Full-Size Keys,
3340 VCO with 4 Simultaneous Waveforms,
VCF, NovaMod FM Sources, 32-Step Sequencer,
Arpeggiator and Live Performance Kit
985-40000-01104 Rev.A
2021-02-03 page 1 of 5
Condential, for internal use only. Not to be reproduced.
User Support Bulletin
Introduction
The unit is carefully calibrated at the factory. The performance may change over time or due to environmental changes,
and the following recalibration procedures can be used to bring it back to its factory settings.
Equipment required
1. A multimeter (with 1 mv resolution)
2. A 3.5 mm cable (mono or stereo should be ne)
Synthesizers and Samplers
MS-1-BK /
MS-1-BU / MS-1-RD
page 2 of 5page 2 of 5
Remove all unused cables from the MS-1.
Set the controls 1 to 8 to the position shown in the right hand column of this table.
Set all the other faders, knobs and switches shown in the photo.
Preparation
Make sure your MS-1 has been powered on for at least 30 minutes, and that it is situated in a place where the
temperature will not change drastically during calibration.
Calibration Procedure
1
2
4
5 6 78
3
No. Control Set to
1 LFO RATE M
2 WAVE FORM
3GLIDE M
4RANGE 2’
5MAIN
6 SUB OSC 2 OCT DOWN
7VCA GATE
8ENVELOPE GATE
No. CV type Description
1Internal CV Calibrates the internal CV
2Output CV Tunes the CV output
3External CV Compensate oscillator oset for external CV in
Follow all steps in the order in which they are presented.
Synthesizers and Samplers
MS-1-BK /
MS-1-BU / MS-1-RD
page 3 of 5page 3 of 5
Press “Shift + STEP1” to start Internal CV calibration.
All of the sequencer LEDs will light up in sequence after this has nished.
Press “KYBD + STEP” then power on device. All the sequencer LEDs will light up.
Wait for calibration to nish.
Internal CV Calibration
Output CV Calibration
In this mode, these buttons have new functions:
There are four test modes A / B / C / D to be calibrated. Their target voltage is 0V / 1V / 3V / 5V respectively.
Button Name Function
HOLD/REST Select test mode A
RESET/ACCENT Select test mode B
ARP/SETEND Select test mode C
PATTERN/BANK Select test mode D
SHIFT —
PAGE —
PLAY/STOP —
REC Save
Button Name Function
STEP1 Select X1 (about ±1 mV)
STEP2 Select X2 (about ±4.5 mV)
STEP4 Select X3 (about ±9 mV)
STEP4 Select X4 (about ±45 mV)
STEP5 —
STEP6 —
STEP7 —
STEP8 —
KYBD Decrease
STEP Increase
Synthesizers and Samplers
MS-1-BK /
MS-1-BU / MS-1-RD
page 4 of 5page 4 of 5
Connect the Multimeter to CV Out as shown below.
Carry out the Internal CV Calibration before starting this Output CV calibration.
Press “Shift + STEP2” to enter user Output CV calibration mode.
Press “HOLD/REST” to select test mode A. You will need to watch the multimeter to adjust the output voltage.
Press “KYBD” or “STEP” to adjust the CV value until it is close to target level “0V”.
(Press “STEP1” “STEP2” “STEP3” or “STEP4” to select the incremental adjustment size “X1” “X2” “X3” or “X4”)
Press “RESET/ACCENT” to select test mode B.
Press “KYBD” or “STEP” to adjust the CV value until it is close to target level “1V”.
Press “ARP/SETEND” to select test mode C.
Press “KYBD” or “STEP” to adjust the CV value until it is close to target level “3V”.
Press “PATTERN/BANK” to select test mode D.
Press “KYBD” or “STEP” to adjust the CV value until it is close to target level “5V”.
Press “REC” to save and nish Output CV calibration.
Synthesizers and Samplers
MS-1-BK /
MS-1-BU / MS-1-RD
Condential, for internal use only. Not to be reproduced.
Music Tribe accepts no liability for any loss which may be suered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein.
Technical specications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik,
Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Oberheim, Auratone and Coolaudio are trademarks or registered trademarks of Music Tribe Global
Brands Ltd. © Music Tribe Global Brands Ltd. 2021 All rights reserved.
External CV Calibration
Press “Shift + STEP3” to start External CV calibration.
Complete Output CV calibration, then connect the CV out jack to the CV in jack with a 3.5mm cable.
Wait for the calibration to nish, this is indicated by all of the sequencer LEDs will light up in sequence.
Calibration is nished. Reboot the MS-1.
End of Procedure
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Behringer Sintetizzatore
Behringer
Behringer PRO-1 Manuale utente
Behringer
Behringer SYSTEM 100 172 PHASE SHIFTER/DELAY/LFO Manuale utente
Behringer
Behringer K-2 Manuale utente
Behringer
Behringer CRAVE Manuale utente
Behringer
Behringer MODEL D Manuale utente
Behringer
Behringer TD-3 Manuale utente
Behringer
Behringer Legendary 2500 Series Manuale utente
Behringer
Behringer DEEPMIND 12 Manuale utente
Behringer
Behringer MonoPoly Istruzioni per l'installazione
Behringer
Behringer PRO-800 Manuale utente
Behringer
Behringer SYSTEM 15 Manuale utente
Behringer
Behringer POLY D Manuale utente
Behringer
Behringer K-2 Manuale utente
Behringer
Behringer VOCODER VC340 Manuale utente
Behringer
Behringer MonoPoly Manuale utente
Behringer
Behringer ODYSSEY Manuale utente
Behringer
Behringer DEEPMIND 12 Manuale utente
Behringer
Behringer 110 VCO/VCF/VCA Manuale utente
Behringer
Behringer NEUTRON Istruzioni operative e di manutenzione
Behringer
Behringer D A-440 Istruzioni per l'installazione
