Belden Hirschmann RS20 Series Manuale utente

RS20 Basic

Release

11/10

Technical Support

[email protected]

User Manual

Installation

Industrial ETHERNET Rail Switch

RS20 Basic Family

RS20

0V 0V

FAULT

+24V

(P2)

Aufkleber MAC-Adresse

IP-ADDRESS

V.24

+24V

(P1)

12FAULT

RS20-0400...B

RS20

LS DA

+24V(P1) 0V 0V

FAULT

+24V(P2)

Aufkleber MAC-Adresse

IP-ADDRESS

LS DA

V.24

P12 FAULT

RS20-0800...B

Downloaded from Arrow.com.

The naming of copyrighted trademarks in this manual, even when not specially indicated, should

not be taken to mean that these names may be considered as free in the sense of the trademark

and tradename protection law and hence that they may be freely used by anyone.

translation, conversion into any electronic medium or machine scannable form is not permitted,

either in whole or in part. An exception is the preparation of a backup copy of the software for

your own use. For devices with embedded software, the end-user license agreement on the

enclosed CD applies.

The performance features described here are binding only if they have been expressly agreed

when the contract was made. This document was produced by Hirschmann Automation and

Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right

to change the contents of this document without prior notice. Hirschmann can give no guarantee

in respect of the correctness or accuracy of the information in this document.

Hirschmann can accept no responsibility for damages, resulting from the use of the network

components or the associated operating software. In addition, we refer to the conditions of use

specified in the license contract.

You can get the latest version of this manual on the Internet at the Hirschmann product site

(www.beldensolutions.com).

Printed in Germany

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

Tel.: +49 1805 141538

RS20 Basic 039 524-200-17-1110 – 3.11.10

Downloaded from Arrow.com.Downloaded from Arrow.com.

RS20 Basic

Release

11/10 3

Contents

Safety instructions 4

About this Manual 9

Key 9

1 Device description 10

1.1 Description of the device variants 11

1.1.1 Combination options for RS20-...B 12

1.1.2 Number of ports and media for RS20-...B 13

2 Assembly and start-up 15

2.1 Installing the device 15

2.1.1 Unpacking and checking 15

2.1.2 Insert data in label area 15

2.1.3 Connecting the terminal blocks for supply voltage and

signal contact 16

2.1.4 Installing the device on the DIN rail, grounding 17

2.1.5 Dimension drawings 18

2.1.6 Installing the terminal block, start-up procedure 19

2.1.7 Connecting the data lines 19

2.2 Display elements 20

2.3 Basic set-up 21

2.4 Disassembling the device 23

3 Technical data 24

A Further Support 29

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

4RS20 Basic

Release

11/10

Safety instructions

Notes on safety

This manual contains instructions to be observed for ensuring your

personal safety and for preventing damage. The warnings appear next to

a warning triangle with a different heading depending on the degree of

danger posed:

Danger! 

Means that death, serious physical injury or significant damage

to property will occur if the corresponding safety measures are

not carried out.

Warning! 

Means that death, serious physical injury or significant damage

to property could occur if the corresponding safety measures

are not carried out.

Caution! 

Means that minor physical injury or damage to property can

occur if the required safety measures are not carried out.

Note: Contains important information on the product, on how to manage

the product, or on the respective section of the documentation to which

your special attention is being drawn.

Certified usage

Please observe the following: The device may only be employed for the

purposes described in the catalog and technical description, and only in

conjunction with external devices and components recommended or

approved by the manufacturer. The product can only be operated

correctly and safely if it is transported, stored, installed and assembled

properly and correctly. Furthermore, it must be operated and serviced

carefully.

Supply voltage

For safety reasons the devices have been designed to operate at low

voltages. Thus, they may only be connected to the supply voltage

connections and to the signal contact with SELV circuits with the voltage

restrictions in accordance with IEC/EN 60950-1.

The supply voltage is electrically isolated from the housing.

Use undamaged parts.

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

RS20 Basic

Release

11/10 5

Relevant for North America: For use in Class 2 circuits.

The device may only be connected to a supply voltage of class 2 that

fulfills the requirements of the National Electrical Code, Table 11(b). If

the voltage is being supplied redundantly (two different voltage

sources), the combined supply voltages must fulfill the requirements of

the National Electrical Code, Table 11(b).

Relevant for North America: For use in Class 2 circuits.

Only use copper wire/conductors of class 1, 75 °C (167 °F).

Relevant for North America

for devices certified for hazardous locations:

Power, input and output (I/O) wiring must be in accordance with

Class I, Division 2 wiring methods [Article 501-4(b) of the National

Electrical Code, NFPA 70] and in accordance with the authority having

jurisdiction.

Relevant in Europe for RS20 devices and RS30 devices used in

explosive gas atmospheres according to ATEX Directive 94/9 EC:

Make sure that the device has the following label:

II 3G Ex nA II C T4

The product must be mounted in a suitable IP 54-certified housing

– tested to 4 J impact to minimize the risk of mechanical damage.

For ambient temperatures below -10 °C and above +60 °C use

wiring suitable for both the minimum and maximum temperatures.

Connectors may be connected exclusively in dead-voltage state.

DIP switches may be switched exclusively in dead-voltage state.

The device does not contain any service components. Internal fuses

are only triggered if there is a fault in the device. If the device is not

functioning correctly, or if it is damaged, switch off the voltage supply

and return the device to the plant for inspection.

Only switch on the supply voltage to the device if

- the housing is closed, 

- the terminal blocks are wired up correctly and 

- the terminal blocks are connected.

Shielding ground

Note: The shielding ground of the connectable twisted pair lines is

connected to the front panel as a conductor.

Beware of possible short circuits when connecting a cable section with

conductive shielding braiding.

Housing

Warning!

Never insert sharp objects (small screwdrivers, wires, etc.) into

the inside of the product. There is the risk of an electric shock.

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

6RS20 Basic

Release

11/10

Warning!

When installing the device, make sure the ventilation slots

remain free, as otherwise damage can occur through

overheating.

Only technicians authorized by the manufacturer are permitted to open

the housing.

The housing is grounded via the separate ground screw on the bottom left

of the front panel.

The clearance to the ventilation slots of the housing must be at least

10 cm (3.94 in).

The device must be installed in the vertical position.

If installed in a living area or office environment, the device must be

operated exclusively in switch cabinets with fire protection

characteristics in accordance with EN 60950-1.

Environment

The device may only be operated at the specified surrounding air

temperature (temperature of the surrounding air at a distance of up to 5

cm (1.97 in) from the device) and relative air humidity specified in the

technical data.

Install the device in a location where the climatic threshold values

specified in the technical data will be observed.

Use the device only in an environment within the contamination level

specified in the technical data.

Qualification requirements for personnel

Qualified personnel as understood in this manual and the warning signs,

are persons who are familiar with the setup, assembly, startup, and

operation of this product and are appropriately qualified for their job. This

includes, for example, those persons who have been:

trained or directed or authorized to switch on and off, to ground and to

label power circuits and devices or systems in accordance with current

safety engineering standards;

trained or directed in the care and use of appropriate safety equipment

in accordance with the current standards of safety engineering;

trained in providing first aid.

General safety instructions

Electricity is used to operate this equipment. Comply with every detail of

the safety requirements specified in the operating instructions regarding

the voltages to apply (see page 4).

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

RS20 Basic

Release

11/10 7

Non-observance of these safety instructions can therefore cause material

damage and/or serious injuries.

Only appropriately qualified personnel should work on this device or in

its vicinity. These personnel must be thoroughly familiar with all the

warnings and maintenance procedures in accordance with this

operating manual.

The proper and safe operation of this device depends on proper

handling during transport, proper storage and assembly, and

conscientious operation and maintenance procedures.

Never start operation with damaged components.

Only use the devices in accordance with this manual. In particular,

observe all warnings and safety-related information.

Any work that may be required on the electrical installation may only

be carried out by personnel trained for this purpose.

Note: LED or LASER components in compliance with IEC 60825-1

(2001):

CLASS 1 LASER PRODUCT

CLASS 1 LED PRODUCT

Warning 

Laser light 

Do not look into the beam or view it directly with optical

instruments (e.g. magnifying glasses, microscopes). 

Failure to observe this warning within a distance of 100 mm

can endanger your sight.

Light is emitted from the optical connections or from the

ends of the optical fibers that are connected to them. Light

Emitting Diode CLASS 2M, wave length 650 nm, power <2

mW, according to 

DIN EN 60825-1:2003-10.

National and international safety regulations

Make sure that the electrical installation meets local or nationally

applicable safety regulations.

CE marking

The devices comply with the regulations contained in the following

European directive(s):

2004/108/EG

Directive of the European Parliament and the council for standardizing

the regulations of member states with regard to electromagnetic

compatibility.

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

8RS20 Basic

Release

11/10

In accordance with the above-named EU directive(s), the EU conformity

declaration will be at the disposal of the relevant authorities at the

following address:

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Tel.: +49 1805 141538

The product can be used in living areas (living area, place of business,

small business) and in industrial areas.

Interference immunity: EN 61000-6-2:2005

Emitted interference: EN 55022:2006 + A1:2007 Class A

Warning!

This is a class A device. This device can cause interference in

living areas, and in this case the operator may be required to

take appropriate measures.

The assembly guidelines provided in these instructions must be

strictly adhered to in order to observe the EMC threshold values.

FCC note:

This device complies with part 15 of FCC rules. Operation is subject to the

following two conditions : (1) This device may not cause harmful

interference; (2) this device must accept any interference received,

including interference that may cause undesired operation.

Appropriate testing has established that this device fulfills the

requirements of a class A digital device in line with part 15 of the FCC

regulations.

These requirements are designed to provide sufficient protection against

interference when the device is being used in a business environment.

The device creates and uses high frequencies and can radiate same, and

if it is not installed and used in accordance with this operating manual, it

can cause radio transmission interference. The use of this device in a

living area can also cause interference, and in this case the user is

obliged to cover the costs of removing the interference.

Recycling note

After usage, this product must be disposed of properly as electronic

waste, in accordance with the current disposal regulations of your county,

state and country.

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

RS20 Basic

Release

11/10 9

About this Manual

The “Installation” user manual contains a device description, safety

instructions, a description of the display, and the other information that you

need to install the device.

The following manuals are available as PDF files on the CD-ROM supplied:

Installation user manual

Basic Configuration user manual

Redundancy Configuration user manual

Web-based Interface reference guide

Command Line Interface user manual

The Network Management Software HiVision/Industrial HiVision provides

you with additional options for smooth configuration and monitoring:

Configuration of multiple devices simultaneously.

Graphical interface with network layouts.

Auto-topology discovery.

Event log.

Event handling.

Client / Server structure.

Browser interface

ActiveX control for SCADA integration

SNMP/OPC gateway

Key

The symbols used in this manual have the following meanings:

Listing

Work step

Subheading

10 RS20 Basic

Release

11/10

1 Device description

The RS20 Basic devices are designed for the special requirements of

industrial automation. They meet the relevant industry standards, provide

very high operational reliability, even under extreme conditions, and also

long-term reliability and flexibility.

The devices allow you to set up switched industrial ETHERNET networks

that conform to the IEEE 802.3 and 802.3u standards using copper wires or

optical fibers in a line or ring structure.

The devices work without a fan.

The voltage is supplied redundantly.

The devices are mounted very quickly by snapping them onto the DIN rail.

Depending on the device variant, you can choose various media to connect

terminal devices and other infrastructure components:

twisted pair cable

multimode F/O

singlemode F/O

The twisted pair ports support:

Autocrossing

Autonegotiation

Autopolarity

There are a number of convenient options for managing the device.

Administer your devices via:

a Web browser

management software (e.g. HiVision)

a V.24 interface (locally on the Switch)

The HIPER-Ring redundancy concept enables a quick reconfiguration. With

one additional connection, projection remains simple.

Product configuration data can be provided by:

diagnosis displays

displaying the operating parameters

a label area for the IP address

Depending on the software you choose, the devices provide you with a large

range of functions:

Redundancy functions

Redundant ring structure

HIPER-Ring

Redundant power supply

Security

Protection from unauthorized access

Blocking of unauthorized messages (MAC or IP based)

Altri manuali per Hirschmann RS20 Series

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Belden Interruttore

Belden

Belden HIRSCHMANN OCTOPUS OS24 Series Manuale utente

Belden

Belden Hirschmann DRAGON MACH Series Manuale utente

Belden

Belden Hirschmann GREYHOUND GRS1042 Manuale utente

Belden

Belden HIRSCHMANN GREYHOUND GRM Series Manuale utente

Belden

Belden Hirschmann RS20 U Series Manuale utente

Belden

Belden HIRSCHMANN Octopus II Manuale utente

Belden

Belden HIRSCHMANN MACH 4000 Series Manuale utente

Belden

Belden HIRSCHMANN EESX Series Guida rapida alla configurazione

Belden

Belden HIRSCHMANN HiOS-2A Manuale utente

Belden

Belden Hirschmann MAMMUTHUS MTS2600 Manuale utente

Belden

Belden Hirschmann SPIDER 8TX EEC Manuale utente

Belden

Belden Hirschmann SPIDER-SL-20-08T1999999SY9HHHH Manuale utente

Belden

Belden HIRSCHMANN MACH4002-48+4G Manuale utente

Belden

Belden Grass Valley K-Frame Come usare

Belden

Belden Hirschmann MACH4002 Series Manuale utente

Belden

Belden HIRSCHMANN Dragon PTN CSM310-A Manuale utente

Belden

Belden HIRSCHMANN GRS105 Manuale utente

Belden

Belden Hirschmann RED25 Series Manuale utente

Belden

Belden Hirschmann MACH104-PoEP Series Manuale utente

Belden

Belden Hirschmann MACH102 Series Manuale utente

Belden

Belden grass valley MASTERPIECE 12G-SDI Manuale utente

Belden

Belden Thinklogical TLX48 Manuale utente

Belden

Belden HIRSCHMANN RSPE 30 Manuale utente

Belden

Belden Hirschmann MACH104-PoEP Series Manuale utente

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente