Bellman & Symfon BE1442 Istruzioni per il montaggio

DESIGN FOR EARS™

BE1444_005MAN002

BE1444_005MAN002-433-Visit-Flashreceiver.indb 1 2017-09-06 09:33:53

BE1444_005MAN002-433-Visit-Flashreceiver.indb 2 2017-09-06 09:33:53

Visit ash receiver

Récepteur Flash Visit

BE1442/BE1444

BE1444_005MAN002-433-Visit-Flashreceiver.indb 3 2017-09-06 09:33:53

4 5 6

315

CMY

front-fold-BE1444.pdf 1 8/2/2016 2:58:26 PM

Flash receiver

BE1442/BE1444

BE1444_005MAN002-433-Visit-Flashreceiver.indb 4 2017-09-06 09:33:54

Overview

1 Rotatable reector

2 Flash

3 Visit LED, orange

4 Visit LED, green

5 Visit LED, yellow

6 Visit LED, red

7 Connector for power supply

8 Telephone input for

analogue telephone

9 Mute / test button

10 Bed shaker output

11 Cable holder

12 Table stand/battery compartment

13 External socket

14 Power LED

Overview

1 Rotatable reector

2 Flash

3 Visit LED, orange

4 Visit LED, green

5 Visit LED, yellow

6 Visit LED, red

7 Connector for power supply

8 Telephone input for

analogue telephone

9 Mute / test button

10 Bed shaker output

11 Cable holder

12 Table stand/battery compartment

13 Smoke alarm menu button

14 Power LED

15 Smoke alarm supervision LED

Flash receiver

BE1442

Flash receiver

BE1444

BE1444_005MAN002-433-Visit-Flashreceiver.indb 5 2017-09-06 09:33:54

Bellman Visit ash receiver, BE1442/BE1444

General

The ash receiver is part of the Visit smart home system that helps you to keep tabs on your

home. It alerts you with bright ashes when the doorbell or telephone rings, when your

baby needs you or if a re should occur.

It is activated via radio signals from the Visit transmitters and features colored LED’s to dif-

ferentiate the alarms. You can also connect a bed shaker (optional accessory) and wake up

to vibrations if something should happen while you are asleep. For indoor use.

Getting started

Unpacking, installing and testing the unit

1 Connect the power supply to the receiver and the mains power. Pull the battery tab

at the bottom. Place the receiver on a level surface or mount it on the wall using the

BE9075 wall bracket accessory. The receiver should be placed where it best can be seen.

2To test the radio link you need a Visit transmitter. Press the test button/s on the transmitter.

3The receiver starts to ash and lights up the corresponding Visit LED. If a bed shaker is

connected, it will vibrate. A short press on the test button repeats the last indication. If

nothing happens, see Troubleshooting.

4You can connect a Bellman bed shaker, BE1271 (optional accessory) to the bed shaker

output (10) . When the ash receiver is activated, the bed shaker will vibrate.

5You can connect the ash receiver to the landline phone jack via the telephone input (8)

with the BE9105 Telephone Flex (optional accessory) and an adapter plug (optional

accessory). When the phone rings, the ash receiver will alert with ashes and the yellow

LED (5) will light up.

Function

Radio key

All Bellman Visit units are set to the same radio key as factory default. If you have a neighbour

with a similar system, you can change the radio key so that you do not aect each other’s

systems. Please refer to Installer’s guide in page 10. If you want to change the radio keys.

All units in a Bellman Visit System must have the same radio key in order to operate as a group.

BE1444_005MAN002-433-Visit-Flashreceiver.indb 6 2017-09-06 09:33:54

Indicators and Signals

It is generally the transmitters in the Visit smart home system that determine how the

receivers will indicate an alarm. See the description in the relevant transmitter user manual

for further information.

The Visit ash receiver has a function which allows you to easily check which alarm was

the last one detected. Give a short press on the test button (9) and the last alarm will be

repeated.

System indicators

The LEDs that indicate which transmitter has activated the Bellman Visit Flash

Receiver normally have the following meanings.

Orange LED indicates a baby monitor.

Green LED indicates a door transmitter.

Yellow LED indicates a telephone transmitter.

Red LED indicates a re alarm.

If the green and yellow LEDs blink alternately, this indicates that the Visit ash receiver

is in radio key selection mode. The ash receiver will then wait for a radio signal from a

transmitter in the Visit system which will adjust the receiver to the same radio key as the

transmitter is set to.

Flash light

When the Visit ash receiver is activated, the ash (2) will show a sharp white light.

The ash head (1) can be rotated to point in the direction required The reector can, for

example, be pointed towards a wall to prevent dazzle. A silicone slip-on top is also available

in a variety of colours (art. no. BE9164-BE9167).

Vibration

The Bellman Visit Flash Receiver can power a BE1271 Bellman Bed shaker (optional accessory)

connected to the socket (10) . The bed shaker is placed under the pillow to wake the

user up when the Visit ash receiver is activated.

Refer to the user manual for the relevant Bellman Visit transmitter for more information

about vibration patterns.

BE1444_005MAN002-433-Visit-Flashreceiver.indb 7 2017-09-06 09:33:54

Power LED indications

When the ash receiver is connected to mains power, the power LED lights up in green.

The BE1442/BE1444 ash receiver is also equipped with battery backup and the power LED

indicates the following:

Power LED Status

Green light Connected to mains power. Backup batteries installed.

Green blinks Connected to mains power. No backup batteries detected.

Red light Running on battery backup.

Red blinks Backup batteries nearly depleted.

For further instruction about replacing the batteries, please refer to Installer’s guide “Battery

backup” section in Page 11.

BE1444_005MAN002-433-Visit-Flashreceiver.indb 8 2017-09-06 09:33:54

For further information, please refer to the Installer’s guide.

Troubleshooting in brief

If Try this

Nothing happens. Check that the power supply unit is connected correctly.

Check that there is current in the wall socket.

The receiver is not activated. Check the battery in the transmitters.

Check that the receiver is not placed too far away from the

transmitters by moving it closer to the transmitters.

Check that the receiver is set to the correct radio key. For

further information see Function/Radio key.

The receiver signals when no

transmitter is activated.

Change the Radio Key on all units in the system. For further

information see Appendix/Radio key.

BE1444_005MAN002-433-Visit-Flashreceiver.indb 9 2017-09-06 09:33:54

BE1444_005MAN002-433-Visit-Flashreceiver.indb 10 2017-09-06 09:33:54

Altri manuali per BE1442

Questo manuale è adatto per i seguenti modelli

Indice

Lingue:

Altri manuali Bellman & Symfon Ricevitore

Bellman & Symfon

Bellman & Symfon Visit Manuale utente

Bellman & Symfon

Bellman & Symfon Visit 868 BE1450 Manuale utente

Bellman & Symfon

Bellman & Symfon BE1441 Manuale utente

Bellman & Symfon

Bellman & Symfon BE1441 Guida all'applicazione

Bellman & Symfon

Bellman & Symfon BE1442 Manuale utente

Bellman & Symfon

Bellman & Symfon Visit BE1470 Manuale utente

Bellman & Symfon

Bellman & Symfon BE1441 Manuale utente

Bellman & Symfon

Bellman & Symfon BE1450 Manuale utente

Bellman & Symfon

Bellman & Symfon Bellman Visit BE1033 Manuale utente

Bellman & Symfon

Bellman & Symfon Bellman Visit BE1330 Manuale utente

Bellman & Symfon

Bellman & Symfon Visit BE1470 Manuale utente

Bellman & Symfon

Bellman & Symfon BE1441 Manuale utente

Bellman & Symfon

Bellman & Symfon Bellman Visit 868 Manuale utente

Bellman & Symfon

Bellman & Symfon BE8102 Manuale utente

Bellman & Symfon

Bellman & Symfon BE1450 Manuale utente

Bellman & Symfon

Bellman & Symfon Visit Manuale di installazione e funzionamento

Bellman & Symfon

Bellman & Symfon Visit Manuale utente

Bellman & Symfon

Bellman & Symfon Visit Manuale utente

Bellman & Symfon

Bellman & Symfon Visit BE1470 Manuale utente

Manuali Ricevitore popolari di altre marche

Garmin

Garmin GA 23 Manuale utente

Aiphone

Aiphone PS-12F Manuale utente

IMES

IMES TCS-01CA-PMI Manuale utente

BWI Eagle

BWI Eagle AIR-EAGLE SR Manuale

AMIMON

AMIMON AMN12310 WHDI Manuale utente

Dual

Dual DMCPA79BT Istruzioni operative

Sound Associates

Sound Associates SA652P Manuale utente

Sherwood

Sherwood NewCastle R-772 Manuale utente

Audio

Audio A10-RX Series Manuale utente

AllSee

AllSee PushShare PSRV1.1 Manuale utente

DEMAG

DEMAG DRC-DR D2 Manuale utente

Teleco

Teleco TVRCL868A02 Manuale utente

Bosch

Bosch RF3222E Manuale utente

Kramer

Kramer 631R Manuale utente

Xpress

Xpress xmc10 Manuale utente

JVC

JVC KD-MR1BTS Manuale utente

Omega Engineering

Omega Engineering UWTC-REC3 Manuale utente

e-survey

e-survey E300 Pro Manuale utente