Beltronics Vector LR Manuale utente

Advanced

PROTECTION

System

with Shadow Technology®

®®®®

Operating instructions for

model 975

DIGITAL PLL SYNTHESIZED

OSCILLATOR

VECTOR LR Remote

REMOTE DETECTOR

RADAR

•

LASER

•

SAFETY

Ultimate Performance. Proven Technology.

INTRODUCTION

SHADOW TECHNOLOGY®II

SELECTABLE FEATURES

Thank you for purchasing a BELTRONICS Remote installation

Radar/Laser/Safety detector.

Your VECTOR LR Remote detector provides all the benefits of full

coverage Radar and laser detection as well as detection of the Safety

Warning System™— all in the discretion of a concealed installation.

To ensure maximum benefit from your new VECTOR LR Remote,

please read all operating instructions completely as well as the

accompanying installation instructions enclosed.

VECTOR LR REMOTE contains Shadow Technology®II, making it

undetectable to the Interceptor VG-2 or any other Radar Detector

Detector (RDD). Only Shadow Technology®II has been consistently

proven undetectable to the Interceptor VG-2.

1. Auto-Mute On/Off

Select Auto-Mute ON for several X,K, Super Wideband Ka audio alerts

followed by a “clicking” tone to quietly inform you for the duration of

the signal. Auto-Mute OFF provides a continuous series of X,K, Super

Wideband Ka audio alerts. Factory setting is Auto-Mute OFF.

(see page 9)

2. Safety Warning System®(sws™)

VECTOR LR Remote detects encoded signals from sws™ transmitters

and provides distinct alerts for: Highway Construction/Maintenance,

Highway Hazard Zones, Weather Related Hazards, Emergency/Slow

Moving Vehicles and Travel/Convenience Information.

For a complete description of sws™ of audio and visual alerts, see page 16

3. X/K/Ka Band On of Off

Select “X ON/X OFF”, “K ON/K OFF” or “Ka ON/Ka OFF” depending upon

your driving environment and selectivity requirements. Factory setting

is X/K/Ka ON. (see page 9).

4. Four Ka Narrow Frequencies

Select Ka Narrow sweeps of 33.8 GHz, 34.36 GHz, 34.7 GHz or

35.5 GHz. Narrow Band Ka frequencies are especially useful in areas

where you know a specific Ka Narrow sweep is used. Factory setting is

Super Wideband Ka ON. (see page 9)

Table of Contents

Profile of Features . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Description of Features . . . . . . . . . . . . . . . . . . . . . . 5

kPower-on Test Sequence . . . . . . . . . . . . . . . . . . 5

kTutorial Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

kLow Voltage Warning . . . . . . . . . . . . . . . . . . . . . 6

kLoss of Antenna Connection . . . . . . . . . . . . . . . 6

kMemory Retention of Feature Selections . . . . . 6

kAdjusting the Audio Level . . . . . . . . . . . . . . . . . 6

kAudio/Visual Alert for Instant-On/Pulsed Radar . 7

kDRK (Dim/Dark) Button . . . . . . . . . . . . . . . . . . . 7

kAUD (Auto-Mute/Volume Control) Button . . . . 7

kCTY (City/Highway) Button . . . . . . . . . . . . . . . . 8

kCity X/K/Ka Mode . . . . . . . . . . . . . . . . . . . . . . . 8

kReset to Factory Settings . . . . . . . . . . . . . . . . . . 9

Selectable Features . . . . . . . . . . . . . . . . . . . . . . . . . 9

kEntering Selectable Features Mode . . . . . . . . . . 11

Understanding Radar, Laser and SWS™. . . . . . . . . . 12

Interpretation of Alerts . . . . . . . . . . . . . . . . . . . . . . 13

kRadar Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

kTypical False Alert . . . . . . . . . . . . . . . . . . . . . . . 16

kLaser Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

kSafety Warning System®(SWS™) Alerts . . . . . . . 17

Performance Verification . . . . . . . . . . . . . . . . . . . . . 17

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Consumer Warranty . . . . . . . . . . . . . . . . . . . . . . . . . 19

Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

kWarranty Service . . . . . . . . . . . . . . . . . . . . . . . . 20

kPost-Warranty Service . . . . . . . . . . . . . . . . . . . . 21

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Profile of Features

1. Remote Control Panel Unit: compact design fits

discretely and easily in any vehicle.

2. PWR (Power) Button:pressing PWR briefly will turn

the unit ON. Pressing PWR a second time will cancel

the power-up test sequence.

3. H/C (Highway/City) Indicator: illuminates green

for highway mode, and amber for the City X mode.

City X/K/Ka is confirmed by the flashing green/

amber LED, followed by solid illuminator of the

amber LED.

4. DRK (Bright/Dim/Dark) Button: provides dim or

dark settings of the LED display for discreet night

travel. Audio alerts are not affected by this mode.

5. AUD (Audio-Mute) Button: provides manual muting

of X, K, Super Wideband Ka Radar and sws™ alerts.

Pressing and holding the AUD button will change the

audio level.

6. CTY (City/Highway) Button: minimizes unwanted X

band alerts without reducing sensitivity. City X/K/Ka

reduces falsing on all three bands.

7. X/K/Ka/sws™ Band Visual Alerts : the alert

received is confirmed by the illumination of the

appropriate LED.

8. Four-LED Display: LEDs illuminate sequentially to

confirm signal strength of Radar signals. A different

alert pattern confirms detection of Laser and Safety

Warning System®(sws™).

9. Audio Speaker: all audible alerts are emitted from

this location.

10 . Antenna Sensor: contains the electronics which

detect police Radar. This antenna sensor installs within

the engine compartment of the vehicle.

11. Antenna Face: receiving portion of the antenna sensor

must have a clear, unobstructed view of the road ahead.

12 . Front Laser Sensor: with 11’ cable mounts onto the

windshield using the supplied suction cup.

13 . Rear Laser Sensor: with 17’ cable mounts to rear

window of vehicle.

14 . Windshield Accessory Cover: remove the cover to

insert the suction cup mount.

15 . Optical Opening: Laser signals are received at this

side of the Laser sensor which must have a clear,

unobstructed view of the road ahead.

Description of Features

Power-on Test Sequence

Each time your unit is turned on, alerts for Laser, X, K,

Ka and Safety Warning System™are presented briefly.

This is immediately followed by the status of the four

Selectable Features:

1. Auto Mute – a clicking tone confirms if feature is

engaged.

2. Safety Warning System®– illumination if the green

“S” LED confirms if feature is engaged.

3. X/K/Ka Bands – illumination of the appropriate LED

confirms if band is activated. Full illumination of four

signal strength LED, coupled with the illumination of

the Ka LED confirms Super Wideband Ka mode.

4. Ka Narrow Bands –With Super Wideband Ka turned

OFF, any Ka narrow frequency which is engaged is

confirmed by rapid flashing of appropriate signal

strength LED (see page 10).

Pressing PWR anytime during the power up test

sequence will suspend the normal power up test

sequence; your unit will be ready for operation.

Tutorial Mode

The tutorial mode allows you to become more

familiar with all audible and visual alerts. To engage

this mode, press the AUD and the CTY buttons

simultaneously while the unit is ON. The audio/visual

alerts will be presented slowly in order of Laser, K, X,

Ka and SWS™. The tutorial mode will cycle these

audio/visual alerts continuously. Press the P/V button

to exit. Two “beeps” confirm exiting from the tutorial

mode. Your unit is now ON and ready for operation.

Set and Forget Memory

Any time VECTOR LR Remote is turned OFF all

feature settings you have selected are retained in the

unit’s memory. Set and Forget Memory eliminates the

need to reset your preferred feature settings each

time your unit is turned OFF and then back ON.

Low Voltage Warning

VECTOR LR Remote continually checks voltage to

ensure proper performance. The unit’s operating

range is 10.0 to 16.0 volts. If voltage falls below 10.0,

the highway (H) or city (C) indicator will flash,

coupled with a series of steady audible “beeps”.

Loss of Antenna Connection

In the event the control panel and Radar antenna are

not properly connected, the X/K/Ka band indicators

will flash, coupled with steady audible “beeps”.

Audio/Visual Alert for Instant-On/Pulsed Radar

This type of signal appears suddenly when a Radar

unit is “triggered”. The instant-on or pulsed alert

consists of an intense, three-second, X, K or Super

Wideband Ka audio “burst”, coupled with the flashing

of the four-LED display.

DRK (Bright/Dim/Dark) Button

The DRK button allows selection of a dim or dark setting

for all LEDS. To engage dim mode, press the DRK button

once. A single “beep” confirms your selection. To

completely cancel the illumination of all LEDS, press DRK

a second time. You’ll notice the city/highway LED remains

dim to confirm your unit is receiving power. To return to

a full bright setting, press the DRK button a third time;

two “beeps” confirm this selection. Use of the DIM

button does not affect audio alerts.

Important – if you press the DRK button and do not receive

audible confirmation, the audio level has been set too low.

AUD (Audio Mute/Volume Control) Button

Manual Muting of Audio Alerts (Radar and SWS

™

)

Whether Auto-Mute is selected ON or OFF in

Selectable Features, the audio alerts can be completely

muted by pressing the AUD button during an alert.

No audible alert will be heard for approximately 12

seconds. If the signal is still present after 12 seconds,

the unit will remain in manual mute mode.

Volume Control

Press and hold AUD button to engage the volume

control. Release the AUD button when you have reached

your desired audio setting. To reverse direction of the

volume, release and press AUD a second time.

Note – because Laser alerts are not lengthy or

sustained, muting is not required (see page 17).

CITY (City/Highway) Button

The City X mode has been designed to effectively

reduce unwanted audio alerts caused by intrusion

alarms, door openers, and other devices which share

X band with police Radar – without reducing

sensitivity. Signals from non-police Radar sources are

frequently encountered in urban and suburban areas,

making use of this mode ideal in these areas.

Pressing the CTY button once engages the City X

mode which is confirmed by a single “beep” and the

illumination of the yellow city LED labeled H/C. Once

engaged, weak X band signals encountered will

produce no audible alert until the signal strength

reaches a preset level. However visual alerts are

processed the instant an X band signal is detected,

keeping you quietly informed. Since most “false” X

band signals are weak, the use of the city node allows

you to drive out of their range before they reach

preset level and trigger a full audio alert. In contrast,

signals from X band traffic Radar are generally

stronger and will exceed the preset level, causing a

full X band audio alert.

Activating the City X mode will not change Super

Wideband Ka, K or instant-on X band Radar alert

patterns.

Note – the city mode has no effect on the reception

of Laser or SWS™.

City X/K/Ka

City X/K/Ka provides an alternate approach for

improving X, K and Ka band selectivity and is ideal

for use in areas with a high level of microwave

transmissions which can cause falsing on all three

bands. To engage City X/K/Ka mode, press the City

button twice. City X/K/Ka is confirmed by the

alternate flashing of the green/amber H/C LED for

one second. After the one second, the LED returns to

solid amber illumination.

Once engaged, weak X, K or Super Wideband Ka

signals encountered will produce no audible alerts until

the signal strength reaches a preset level. Visual alerts

are processed the instant an X, K or Super Wideband

Ka signal is detected, keeping you quietly informed.

Pressing CTY a third time returns you to highway mode;

two beeps and the illumination of the green H/C LED

confirms highway mode.

Reset to Factory Settings

You can reset your unit to factory settings for volume,

DRK, AUDIO, CITY and Selectable Features. With the unit

OFF press and hold the AUD and CTY buttons, then

press the PWR button. Two “beeps” will confirm factory

settings are reset. Your unit is now ON and ready for

operation.

Selectable Features

Auto-Mute, Safety Warning System®, X, K, Super

Wideband Ka ON/OFF and the four Ka Narrow frequencies:

33.8 GHz, 34.36 GHz, 34.7 and GHz, 35.5 GHz, are all

features that may be selected ON or OFF, depending

upon your preference.

Auto-Mute On/Off

When activated, unit will provide several X, K, Super

Wideband Ka audio alerts followed by a “clicking” tone

to keep you quietly informed for as long as the signal is

present. The clicking becomes more rapid as the

strength of the Radar signal increases. Auto-Mute

enables you to conveniently monitor extended

encounters without having to manually mute or adjust

the volume setting.

Note – because of their urgency, Laser alerts are not

affected.

With Auto-Mute off, unit will provide a continuous

series of X, K, Super Wideband Ka or Laser audio

alerts. This standard setting is often preferred when

background noise in a vehicle is loud. Factory setting

is Auto-Mute off. Auto-Mute ON is confirmed by the

FULL illumination of all 4 red LEDs in the signal

strength meter. Auto-Mute off is confirmed when the

same 4 red LEDs flash.

Safety Warning System®(SWS™) – LED#1

When activated, unit will detect signals from SWS™

transmitters and provide audio/visual warnings if

SWS™transmitters are in use. Factory setting is ON.

X Band On/Off – X BAND LED

When activated, unit will detect X Band signals

(10.456 GHz - 10.60 GHz).

K Band On/Off – K BAND LED

When activated, unit will detect K Band signals

(24.050 GHz - 24.205 GHz).

Super Wideband Ka On/Off – KA BAND LED

When activated, unit will detect Super Wideband Ka

signals (33.4 GHz - 36.0 GHz).

Ka Narrow Band (33.8 GHz) On/Off (LED#1)

When activated, unit will detect ONLY the 33.8 GHz

segment of the Ka bandwidth.

Ka Narrow Band (34.36 GHz) On/Off (LED#2)

When activated, unit will detect ONLY the 34.36 GHz

segment of the Ka bandwidth.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Beltronics Rilevatore radar

Beltronics

Beltronics Professional GX65 Manuale utente

Beltronics

Beltronics STiR Plus Manuale utente

Beltronics

Beltronics Express 935 Manuale utente

Beltronics

Beltronics Pro200 Professional series Manuale utente

Beltronics

Beltronics Ultimate Pro 500 Manuale utente

Beltronics

Beltronics Ultimate Pro 200 Manuale utente

Beltronics

Beltronics RX75PLUS - RX-75 PLUS Radar Detector Manuale utente

Beltronics

Beltronics Express 916 Manuale utente

Beltronics

Beltronics Express 946 Manuale utente

Beltronics

Beltronics BEL990 International Manuale utente

Beltronics

Beltronics STi Driver - STi Driver Radar Detector Manuale utente

Beltronics

Beltronics V960/V940 Manuale utente

Beltronics

Beltronics Express 795 Manuale utente

Beltronics

Beltronics V990 Manuale utente

Beltronics

Beltronics Sti-R Manuale utente

Beltronics

Beltronics Professional RX75 PLUS Manuale utente

Beltronics

Beltronics Vector 955 Manuale utente

Beltronics

Beltronics STi Magnum Professional Series Manuale utente

Beltronics

Beltronics BEL Pro RX65 Manuale utente

Beltronics

Beltronics BEL975R - BEL VECTOR LR Remote Radar/laser... Manuale utente

Beltronics

Beltronics XR70 Manuale utente

Beltronics

Beltronics Vector 995 Manuale utente

Beltronics

Beltronics Professional RX55 Manuale utente

Beltronics

Beltronics Vector 940 Manuale utente

Manuali Rilevatore radar popolari di altre marche

Cobra

Cobra XRS 9700 Manuale utente

Inforad

Inforad v3 Manuale utente

Cobra

Cobra ESD9200 Istruzioni operative

Escort

Escort C65 Manuale utente

Cobra

Cobra SPX 7800BT Manuale utente

Escort

Escort max 360c Manuale utente

Cobra

Cobra XRS 9940 Manuale utente

Lowrance

Lowrance LRA-2400 Manuale utente

Cobra

Cobra ESD-9160 Manuale utente

Whistler

Whistler CR80 Manuale utente

Stinger

Stinger VIP Manuale utente

Cobra

Cobra XRS 9430 Manuale utente

Cobra

Cobra Pro 9680 Manuale operativo

Escort

Escort SmartRadar Manuale utente

Whistler

Whistler 1655 Manuale utente

Radenso

Radenso Pro M-Edition Manuale utente

Rocky Mountain

Rocky Mountain RMR-D250 Manuale utente

Cobra

Cobra XRS 9645 Manuale utente