Bemodern Pryzm Volta 42 Guida

Instructions for installation

Patent pending

UK Registered Design

R3 May 2020 200799_1

Volta 42” & Volta 32” Pryzm

Inset Fire Conversion Kit

Conversion Kit Check List P3

Installation- Introduction P4

Assembly- Pre-fabricated Chimney Breast P5

Assembly- Existing Masonry Chimney Breast P6

Assembly- Fire Conversion Kit Installation P7

Assembly- Fire Conversion Kit Installation continued P8

Installation- Positioning the fire P9

Installation- Magnet Bracket P10

Installation- Fixing the Fire P11

Installation- Fixing the Fire continued P12

Installation- Fitting the Trim P13

Maintenance P14

200799_1

Contents

200799_1

Conversion Kit Check List

Please ensure all fixings are present before commencing installation. If anything is missing please

call Customer Services on 01914300901 or email us at customerservices@bemodern.co.uk

Side Panels

Angle Brackets

18 X

No.8 x15mm

Domed-Head

Screws

No.8 x13mm

Pan-Head

Washer Screws

10 Ø x 4mm

Magnets

Magnet Bracket 2X

Fire Support

Brackets

Pre-assembled 1000L or 750L MDF Framework

Dependant on the model purchased

1000L Trim or 750L Trim

Dependant on the model purchased

Note: Please be sure to take extra care when

removing the trim from the packaging

and handling it during installation.

Installation Introduction

200799_1

Before the product can be installed, consideration will need to be given to routing the power supply to the

fire. This will affect the stages of the installation process. We advise a qualified electrician conduct any

electrical parts of the installation.

Note: A single wall socket is required for the operation of the fire, please refer to the separate fire

instructions for further information.

This product has been designed to be installed into a pre-fabricated, or existing Masonry chimney breast.

Please seek advice from a professional, with reference to the structural integrity of the installation site.

If the product is to be installed into a open chimney or flue, it is important that the chimney/flue is blocked

off to prevent any up/down draughts and falling debris which could restrict and alter the airflow of the

product.

The product should never be sealed into an opening with the use of silicones or adhesives as this can also

alter the airflow and hinder any future servicing of the product.

It is essential to include a lintel at the required height to ensure the appliance does not support the weight

of the finished wall.

A pre-assembled MDF framework has been supplied to ensure that the product is installed at the required

minimum internal clearances for operation. Before commencing with installation please ensure the Fire

Support Brackets have been attached to the MDF framework, these set the minimum depth required for

installation- 238mm. As shown in Diagram 1 below.

Diagram 1

Fix the 2 x Fire Support Brackets using 4 x No.8 x15mm Domed-Head Screws into the pre-drilled holes on

the MDF framework . 2 x per bracket.

Fire Support

Brackets

MDF

Framework

For installation into a pre-fabricated chimney breast follow the instructions on Page 5 then continue onto

Page 7.

For installation into a existing Masonry chimney breast follow the instruction on Page 6 then continue onto

Page 7.

MDF

Framework

(mm)

Min Inset

(mm)

Volta 42” 518 1102 Min 238

Volta 32” 518 852 Min 238

Assembly- Pre-fabricated Chimney Breast

200799_1

Before commencing further with the installation please ensure the 2 X Fire Support Brackets have been

attached to the MDF Framework, these set the minimum depth required for installation- 238mm. As shown

on Page 4.

Decide on the installation height of the fire and construct the studwork around the MDF Framework. The

studwork construction in Diagram 2 is for guidance only.

Ensuring the front face of the MDF framework is flush with the studwork, fix in position through the pre-drilled

holes in the MDF Framework. 3 x fixing holes in the top and bottom and 1 x fixing hole in each side.

Diagram 2

MDF

Framework

Fire Support

Brackets

Studwork

Finishing

Plasterboard, skim and decorate the chimney breast, before installing the fire. As shown in Diagram 3.

Note: The fire is installed in a later procedure.

Diagram 3

Assembly- Existing Masonry Chimney Breast

200799_1

Before commencing further with the installation please ensure the 2 X Fire Support Brackets have been

attached to the MDF Framework, these set the minimum depth required for installation- 238mm. As shown

on Page 4.

We recommend sealing the MDF Framework using an appropriate sealer, especially if the installation site is

damp, however this is down to the discretion of the installer.

Decide on the installation height of the fire and using the pre-assembled MDF Framework for guidance,

mark and cut an opening in the brickwork so that the MDF Framework can be fixed flush with the face of

the brickwork. As shown in Diagram 4.

Diagram 4 is for guidance only, the final construction will be dependant on how the existing chimney

breast is built, if a lintel is required, please seek advice from a professional , with reference to the structural

integrity of the installation site.

Ensuring the front face of the MDF Framework is flush with the brickwork, fix in position through the pre-

drilled holes in the MDF Framework. 3 x fixing holes in the top and bottom and 1 x fixing hole in each side.

Alternative fixing points maybe be required depending on the material being fixed into.

Diagram 4

MDF

Framework

Fire Support

Brackets

Lintel

Diagram 5

Finishing

Pasteboard or Patch up, skim and decorate the chimney breast, before installing the fire. As shown

Diagram 5.

Note: The fire is installed in a later procedure.

Assembly- Fire Conversion Kit Installation

200799_1

Remove the existing fire side panels from either side of the fire, as shown in Diagram 6.

Retain the 10 x No.8 x12mm Domed-Head Screws. 5 x per side. The side panels are no longer required

and can be discarded.

If applicable remove the transit brackets from the bottom of the fire, as shown in Diagram 7. Remove the

4 x No.8 x12mm Domed-Head Screws.

The transit brackets and screws are no longer required and can be discarded.

Diagram 6

Diagram 7

Assembly- Fire Conversion Kit Installation Continued ……

200799_1

Fix the 4 x Angle Brackets using the previously retained- No.8 x12mm Domed-Head Screws. 2 x per bracket.

Ensure the brackets are fixed in the correct orientation- the small tab on each bracket should be

positioned, as shown in Diagrams 8 & 9.

Diagram 8

Diagram 9

Tab

The tabs are used to

ensure the brackets

are installed at the

correct distance from

the finished wall

surface in later

procedures.

Installation- Positioning of the Fire

200799_1

Note: Before positioning the fire, connect the fire to a power supply.

The next step is to position the fire in the opening.

Angle the fire into the opening, as shown in Diagram 10, taking care

not to damage the bottom long edge of the finished opening.

Once clear of the opening, position the fire towards the back of the opening, so it is clear of the front edge

and the MDF Framework in the opening is exposed, as shown in Diagram 11. This will enable the magnet

bracket to be fitted. See page 10

Ensure the product is connected to the power supply before proceeding further.

Diagram 10 Diagram 11

Note: Dependant on the model

purchased the fire may require a

two adult person lift.

Installation- Magnet Bracket

200799_1

With the fire pushed to the rear of the opening.

Install the Magnet Bracket, as shown in Diagram 12, using the supplied 2 x No.8 x15mm Domed-Head

Screws, to fix into the pre-drilled holes in the MDF Framework, this will ensure the bracket is fitted centrally in

the opening.

Before fixing in position align the tabs on either end of the bracket with the face of the finished wall

surface, as shown in Diagram 13.

This will ensure the bracket is installed at the correct distance from the front face for the magnet to engage

correctly with the trim in a later procedure.

Diagram 12

Diagram 13

Finished Wall

Surface

Tab

Finished Wall

Surface

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali bemodern Camino da interno

bemodern

bemodern BM-06 2 SLIDE Series Manuale utente

bemodern

bemodern BM-10 Manuale utente

bemodern

bemodern PRIZM MEDIAVUE Manuale di programmazione

bemodern

bemodern Arteon Pryzm 10003SL Guida

bemodern

bemodern BM-091 2 Series Manuale utente

bemodern

bemodern BM-081 2 Series Manuale utente

bemodern

bemodern HANSFORD GRANDE Manuale di programmazione

bemodern

bemodern BROSELEY EVOLUTION Canterbury Remote Manuale

bemodern

bemodern 600CF Manuale utente

bemodern

bemodern Beadnell Manuale del proprietario

bemodern

bemodern Arteon Pryzm 10003SL Manuale utente

bemodern

bemodern Elgin & Hall Istruzioni per il montaggio

bemodern

bemodern Arteon 4119 Manuale utente

bemodern

bemodern Arteon Pryzm 10003SL Guida

bemodern

bemodern Arteon Pryzm 10003SL Manuale di programmazione

bemodern

bemodern Pryzm 750 Manuale utente

bemodern

bemodern EARDF16NG Guida utente

bemodern

bemodern BM-121 2 Series Manuale utente

bemodern

bemodern Juliette Istruzioni per il montaggio

bemodern

bemodern 2603 HE900E Istruzioni per l'installazione

bemodern

bemodern 2893 Manuale utente

bemodern

bemodern BM-05XXX1 Manuale utente

bemodern

bemodern 580 Deluxe Inset Manuale utente

bemodern

bemodern 2599R Manuale utente

Manuali Camino da interno popolari di altre marche

Brigantia

Brigantia 35-DVRS31N-2 Manuale del proprietario

Nordpeis

Nordpeis Bergen Manuale utente

Superior

Superior BCT2536TMN Manuale utente

Quadra-Fire

Quadra-Fire 5100I-GD-B Manuale utente

Renaissance

Renaissance RUMFORD 1000 Manuale utente

Lacunza

Lacunza IV-800 Manuale utente

Baxi

Baxi 940 Istruzioni per l’uso

Dru

Dru Maestro 60/2 Tall RCH Manuale utente

Diamond Fireglass

Diamond Fireglass SS-O22 Manuale utente

HearthStone

HearthStone Windsor Bay 8830 Manuale di programmazione

Napoleon

Napoleon ASCENT B42 Manuale utente

Enviro

Enviro E33GI Manuale utente

Smeg

Smeg L30 FABE Istruzioni di montaggio

KEDDY

KEDDY K700 Manuale utente

Godin

Godin 3451 Manuale utente

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manuale utente

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manuale utente

Desa

Desa CCFPDFT Manuale operativo

bemodern Pryzm Volta 42 Guida

Manuali Camino da interno popolari di altre marche