Benchmark Scientific BeadBlaster 24 Manuale utente
Instruction Manual
BeadBlaster™ 24
D2400
Homogenizer
Foreword
Thank you for purchasing a BeadBlaster™24 Homogenizer. This manual
contains instructions for the proper operation and care of this instrument.
Please read it carefully before operation and keep it available for future use.
Prior to initial operation:
Please check the instrument and the accessories against the packing list
when you first open the shipping carton. Report any damage, discrepancy,
or missing items to the supplier immediately.
Safety Warnings and Guidelines
1. Important operation information:
Read this manual carefully before attempting to operate the instrument.
2. Safety:
3. The operation, maintenance and repair of the instrument should comply with the
basic guidelines and safety warnings below. Noncompliance may interfere with
the useable life of the instrument and safety protection and may void the warranty.
Use this product indoors. Do not operate in a damp or wet
environment.
Before using the instrument, read the manual carefully. This instrument
is designed for use in laboratory environments and must be operated by
skilled personnel with the appropriate training.
Do not attempt to open the casing or repair the instrument. Disassembly
will void the warranty. If there is a service issue with the instrument,
please contact the supplier.
Read this manual prior to powering up the instrument. Pay special
attention to the guidelines and directions below and be familiar with
all safety warnings and guidelines.
Before operation, check to see that the voltage rating on the instrument
matches your local voltage. The rated electrical load of the outlet
should not be lower than that of the instrument's demand. If the power
cord is damaged, it should be replaced. Do not place the power cord
where it will have objects placed on it or where it will be walked on.
When unplugging the instrument, do not pull the plug out of the socket
by the cord.
4. Maintenance
The tube holder should be cleaned with a cloth dampened with a small amount of
alcohol. The outside of the unit can be cleaned with a damp cloth or mild
detergent if required.
The power switch is located on the rear of the instrument. After use,
the power to the instrument should be turned off. If the instrument will
not be used for a long period of time, it should also be unplugged and
covered with a cloth or plastic to keep it free of dust.
The instrument should be unplugged immediately and the supplier
contacted in the event of:
Liquid leaking into the instrument
Smoke or fire
Abnormal operation - ie sound or smell
The instrument has been dropped or outer housing damaged
Instrument function changes
Install the instrument in a cool, dry location free from dust, direct
sunlight or strong lights. The instrument should be placed away from
corrosive gasses, strong magnetic fields, and heat sources. Allow at
least 4 inches on all sides of the instrument for proper air circulation.
Be sure that the air vent at the back of the instrument is not blocked. If
using two instruments, they should be placed at least 3 feet apart.
If samples are processed for an extended time period, many
cycles or without a pause between cycles, thermal breakdown of
the sample tube may occur. Be sure to follow manufacturers
guidelines for lysing kits and tubes.
Always disconnect power to the unit before any cleaning procedure.
Do not apply cleaning solutions directly to the tube holder or chamber.
Do not use corrosive agents while cleaning. Do not submerge the
instrument.
Contents
CHAPTER 1 INTRODUCTION ------------------------------------------------------------------------------ 1
CHAPTER 2 SPECIFICATIONS ---------------------------------------------------------------------------- 2
1. NORMAL OPERATION CONDITIONS: --------------------------------------------------------------- 2
2. THE BASIC PARAMETERS AND CHARACTERISTICS----------------------------------------- 2
CHAPTER 3 BASIC INSTRUCTIONS--------------------------------------------------------------------- 3
1. STRUCTURE OVERVIEW-------------------------------------------------------------------------------- 3
2. OPERATION PANEL--------------------------------------------------------------------------------------- 4
3. DISPLAY------------------------------------------------------------------------------------------------------- 4
CHAPTER 4 OPERATION GUIDE------------------------------------------------------------------------ 5
1. LOADING TUBES------------------------------------------------------------------------------------------- 5
2. PROGRAM SELECTION---------------------------------------------------------------------------------- 7
3. PROGRAM SETTING-------------------------------------------------------------------------------------- 7
4. RUNNING AND STOPPING PROGRAMMED OPERATION------------------------------------ 8
5. MOTOR OVER TEMPERATURE PROTECTION--------------------------------------------------- 8
6. BEAD SELECTION----------------------------------------------------------------------------------------- 9
7. SAMPLE PREPARATION--------------------------------------------------------------------------------10
CHAPTER 5 TROUBLESHOOTING GUIDE ------------------------------------------------------------V
D2400 Homogenizer Manual Chapter 1 Introduction
─1─
Chapter 1 Introduction
The BeadBlaster™24 is a homogenizer for biological samples. It features high speed,
three-dimensional vibration and has a capacity for 24 samples.
Features:
Can break and crack most biological samples (animal and plant tissue,
soils, yeast, spores, microorganisms, etc.)
Processes 24 samples in a minimal amount of time.
On board memory for 50 programmed runs.
Run stops automatically if the cover is opened.
D2400 Homogenizer Manual Chapter 2 Specifications
─2─
Chapter 2 Specifications
1. Normal operating conditions:
Ambient temperature：5C 35C
The relative humidity：≤70%
Power：AC100-240V～50-60Hz
2. The basic parameters and characteristics
Type
Parameter
D2400
Display
OLED
Speed
4.00m/s~7.00m/s, in 0.05m/s increments
Cycle duration
1s~ 1min 30s, in 1s increments
Pause
1s~ 2min, in 1s increments
Number of Cycles
10
Programs
50
Sample Size
24 X 2.0ml tubes
Acceleration time
＜2s
Deceleration time
＜2s
Noise
＜68db
Power
600W
Dimension(WXDXH)
280mm × 360mm × 385mm
Weight（kg）
25.0kg
D2400 Homogenizer Manual Chapter 3 Basic instructions
─3─
Chapter 3 Basic instructions
This chapter focuses on the structure, operation keys and display of the instrument, as well as
preparatory work before starting. Please read this chapter before initial operation.
1. Structure overview
Cover Latch
On/Off button
Power supply plug
Operation panel
Tube retainer
Display screen
Protective cover
Air opening
D2400 Homogenizer Manual Chapter 3 Basic instructions
─4─
2. Operation panel
3. Display
Prog. Use in conjunction with to select the desired program.
Set Set speed, run time, cycle and pause time for the current program.
Modify parameters
Start Run program
Stop Stop program
PROG：01 28ºC
6.50 03
0:30 0:30
SPEED
M/S
M:S
TIME
CYCLE
INTER..
M:S
D2400 Homogenizer Manual Chapter 4 Operation Guide
─5─
Chapter 4 Operation Guide
1. Loading Tubes
1.1 Disengage the locking latch (as shown below), turn the knob counter-clockwise and remove
the tube retainer.
1.2 The tube holder may be filled in or out of the instrument. To remove, simply lift off the shaft.
Place sample tubes into the tube holder and press down until seated. If less than 24
samples are used, they should be evenly distributed in the tube holder. If removed, the tube
holder can then be replaced, making sure the two bumps on the holder line up with the
indentations on the shaft.
Knob
Tube retainer
Locking latch
Sample tube
Tube holder
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Benchmark Scientific Attrezzature da laboratorio
Benchmark Scientific
Benchmark Scientific Accuris Manuale utente
Benchmark Scientific
Benchmark Scientific TC9639 Manuale utente
Benchmark Scientific
Benchmark Scientific SB-12L Manuale utente
Benchmark Scientific
Benchmark Scientific MR-9600 Manuale utente
Benchmark Scientific
Benchmark Scientific Iso-Block BSH6000 Manuale utente
Benchmark Scientific
Benchmark Scientific Accuris MyGel InstaView Manuale utente
Benchmark Scientific
Benchmark Scientific Bioclave Manuale utente
Benchmark Scientific
Benchmark Scientific Accuris SmartReader 96 Manuale utente
Manuali Attrezzature da laboratorio popolari di altre marche
Agilent Technologies
Agilent Technologies 5800 ICP-OES Manuale utente
Endress+Hauser
Endress+Hauser Cleanfit CPA875 Manuale utente
NI
NI PXI-5422 Manuale
Collomix
Collomix Aqix Manuale utente
SPEX SamplePrep
SPEX SamplePrep 6875 Freezer/Mill Series Manuale utente
Ocean Insight
Ocean Insight FLAME-NIR+ Manuale utente
