Best-Rite OneBoard Manuale utente
User Manual – Version 1.1
User Manual
Please read, understand and follow the information contained in this User Manual before installation and
use this product.
Customer Service Department:
1-800-749-2258
(Monday – Friday, 8AM-5PM CST) customercare@moorecoinc.com
Page 2 of 23
Contents
1. Safety Information 3
2. Scope of Supply 7
3. OneBoard Software Installation 8
4. OneBoard Connection 11
5. OneBoard Configuration 12
6. Gestures 14
7. OneBoard Software Operation 17
8.Notices 25
9.Warranty 25
Page 3 of 23
Safety Information
This product was designed for and is intended for use indoor via a USB cable connected to a
desktop or laptop computer. Using this product in an outdoor and/or wet environment could
damage this product and create potentially unsafe conditions.
Meaning of Signal Words
Indicates a potential hazard that could result in serious injury or
death and/or property damage.
Indicates hazards that could result in minor or moderate injury
and/or property damage.
Please read, understand and follow all safety information contained in this User Manual before
installation and use this product:
Do not use this product in an outdoor environment.
Do not use this product near water or moisture. Electric shock may result.
This product is not intended for use by unsupervised children. Always provide proper adult
supervision when using this product around children.
At least two qualified service technicians should perform the installation and removal procedure.
Failure to do so could result in serious personal injury and/or property damage.
Before installation, take the wall material and wall strength into consideration.
Always place this product on a stable and level surface.
Use only the designated MooreCo stands and wallmounts.
Make sure the mounting screws are properly sized to handle the weight of this product.
Make sure the mounting hardware is securely anchored to a solid structure.
Only plug the power cord or power adaptor into an AC power outlet with the proper and indicated
power supply voltage. Only use grounded AC power outlets. Use of this product with the wrong
power supply voltage may result in property damage, fire, or shock.
If the power cord or power plug or power adaptor cannot be plugged into the AC power outlet,
contact a licenses electrician to replace the AC power outlet with a properly grounded (earthed) one.
Page 4 of 23
When you operate this product, the AC power outlet should be near this product and easily
accessible.
The fact that this product operates satisfactorily does not imply that the AC power outlet is grounded
and that the installation is completely safe. For your safety, if you are in any doubt about the
grounding status of the AC power outlet, consult a qualified electrician.
Do not defeat the purpose of the grounded AC power outlet (for example, do not use an outlet
converter).
Always ensure that the power cord or power adaptor is securely and firmly plugged into the
approved AC power outlet. Otherwise, possible electric shock or fire may occur.
Do not pull, bend, rest objects on, or chafe the power cord or power adaptor. Damage to the power
cord or power adaptor can cause fire or electric shock.
Do not attempt to repair the power cord or power adaptor if it becomes damaged. Contact an
authorized service representative for a replacement.
Periodically clean the power cord and power adaptor to ensure the connection is free of dust. Always
ensure that the power cord and power adaptor are unpowered before cleaning. Dirty power cord
connections or power adaptor connections may result in a fire.
Never touch the power cord or power adaptor with wet hands. Electric shock will result.
Stop operation immediately if your product emits smoke, excessive heat, abnormal smell or unusual
noise. These conditions may cause fire or electronic shock. Immediately turn your product off and
unplug the power cord and/or power adaptor, and contact an authorized service representative for
service.
When disconnecting this product from an AC power outlet, pull on the power plug and NOT on the
power cord. Pulling on a power cord forcibly can damage it and cause fire or electric shock.
If an object or liquid get inside this product, turn the product off and unplug the power immediately.
Contact an authorized service representative for service. Operating the contaminated product can
cause fire or electronic shock.
Never open or remove unit covers that are screwed with screws. A high-voltage component can
cause electric shock.
Do not alter this product or modify any parts of the board. Alteration or modification can cause fire or
electronic shock
Before cleaning this product, unplug the power cord and/or power adaptor. Electric shock may result
otherwise.
Do not open or alter the casing of this product. Electric shock or injury may result.
Be careful about the location of the power cord, power plug or power adaptor to avoid it trips
someone or causing this product to fall, etc. It may cause injury or product failure.
Do not place this product, power cord, power adaptor, or accessories where it may be tripped on.
Failure to do say may cause injury.
Page 5 of 23
Use only the included power cord and power adaptor. If another power cord or power plug or power
adaptor is used, fire or electric shock might result.
Do not operate this product in a location with high temperature or high humidity. This product is
suitable to work under: Temperature: 10°C to 40°C; Humidity: 10% to 80%; NO condensation.
Unplug the power cord, power plug or power adaptor from the AC power outlet when:
The power cord or power supply plug is damaged.
A liquid is spilled onto this product.
This product is exposed to rain or water.
This product becomes malfunctions and/or need repairing.
This product falls or after its cabinet is damaged.
This product must be disposed in accordance with the relevant federal, state, and local laws and
regulations.
Do not install this product except by qualified service personnel.
Avoid fire and heat source above 100°C.
When this product is not used over an extended period of time, switch it off and unplug the power
plug or power adaptor. If it is unused and is left connected to a power source for a long period,
degraded insulation may cause electronic shock, current leakage or fire.
Do not position this product in a location where it is unstable.
Do not place this product in a hot humid or dusty environment. Prolonged exposure to these adverse
conditions may cause fire or electric shock.
When moving this product, be sure to unplug the power cord, plug or power adaptor from the AC
power outlet. If this product is moved with the power cord or plug or power attached, it can cause
damage to the power cord, plug or power adaptor which could result in fire or electric shock.
After installing or moving this product, lock the casters when it is hanging on a mobile stand.
If this product is fallen down or damaged, turn this product off and unplug the power cord or power
plug or power adaptor. Otherwise, it may cause fire or electric shock.
Do not put drinks, other liquids or heavy items on the tray or screen. Accidental spillage of liquid into
this product may cause severe damage. If this occurs, turn this product off, unplug the power cord or
power plug or power adaptor and contact an authorized service representative for service.
Do not lean against this product even this product is mounted on the wall.
When this product is not used over an extended period of time, take the batteries out of the
electronic stylus. Otherwise the batteries may leak. Do not use the leaked batteries.
Page 6 of 23
Do not install this product where it may be exposed to direct sunlight, near heating equipment, or
near air-conditioning vents.
Do not install this product in strong sunlight or strong lighting.
Do not install this product in locations where the temperature may change suddenly.
Do not erase with a dirty eraser.
Use Green Erase whiteboard cleaner for hard-to-erase stains.
Fasten the screws tightly to avoid the stand or this product fall which may cause injury or damage.
Before installation, take the wall material and wall strength into consideration. For details, please
consult your dealer.
Page 7 of 23
Scope of Supply
After unpacking, please make sure all of the following parts (subject to your purchase) are
present:
OneBoard – USB
Item Description Quantity
1 Board with built-in IR sensor 1
2 Tray 1
3 Hardware pack (Z-hanger, side tubes, screws, screw anchors) 1
4 USB cable 1
5 Software CD-ROM with user manual 1
6 Pointers (marker size and pen size) 2
7 Eraser 1
Page 8 of 23
OneBoard Software Installation
DO NOT connect OneBoard USB cable to your computer before following the steps below.
Step 1. Install OneBoard software
1. To run the installation program, double-click “OneBoard_Setup.exe” on your
installation CD. You may see a progress bar initially.
2. Click “Next” to begin installing the software
Page 9 of 23
3. Choose the installation destination and click “Next” to continue. You may need to click
“Install” on the next screen.
4. Your installation progress will be displayed.
Page 10 of 23
5. Click “Finish” to exit the installation program after the OneBoard software has been
installed.
6. Plug the USB cable into your OneBoard. Plug the other end of the USB cable into your
computer’s USB port.
7. The OneBoard has been detected and is ready to use when your computer displays
the following dialog:
Indice
