Beta 350-498 RR Guida utente
2013 –2014 350-498 RR
Set Up Manual
8/2013
1) Remove cardboard from
crate. Remove bag with bolts
and upper handle bar clamp
taped to the protective
covering over the seat.
Remove all items from bottom
of crate
2) ) Remove wood support from
lower bar mount and discard.
Retain bolts for handle bar. Remove
protective covering from
motorcycle and handle bar.
3) Install handle bars using the
supplied 8mm bolts and upper
clamp bracket. Torque bolts to 25
nm.
4) Remove additional items from
the box supplied. Item list is as
follows:
-Headlight assembly
-Skid plate
-Frame guards
-Tool kit
-Battery Strap
-Owners manual
-Hardware
6) Cut large tie straps form foot rests
5) Carefully remove Tie-Straps from
front and rear wheels making sure the
motorcycle doesn’t fall over. Remove
the motorcycle from the crate.
7) Attach the computer using the
bolts located on the top triple
clamp. Torque to 10nm.
8) Insert all the electrical
connectors into the matching plugs
located below the computer
including those hanging from the
handle bar.
9) Attach the headlight
connectors located behind the
headlight mask to the proper
plugs located below the
computer.
10) Install the headlight mask bottom
by inserting the lower tab into slot
located in the front fender brace.
11) Finish by securing the rubber
straps located on the sides of the
mask to the upper fork legs.
12) Press the front brake line and
speedometer wire through the slot
on the grommet located on the left
side of headlight mask.
13) Locate the skid
plate and install the
four foam buffers as
shown.
14) Install the skid
plate clips to the tabs
on the lower front frame
rails. Use the two 6mm
bolts to secure the front
of the skid plate.
15) Using the threaded
hole at the lower rear
of the frame, secure the
rear of the skid plate using
the remaining 6mm bolt.
16) Install the right and left frame
guards with zipties and the one bolt
into the swingarm pivot. Make sure
there is one ziptie tied around the
rear brake master cylinder also.
17) Wearing a glove, use your
finger to apply a bead of grease
around the inside edge of the air
filter. This will help keep debris
from passing through. Re-install
the filter making sure all corners
are firmly in place.
18) Holding the Battery, peel the
adhesive sticker from the top.
19) Line up the cells on the
container with the holes on the
top of the battery. Push down
to puncture the foil covers .
This will allow the electrolyte
to drain into the Battery.
20) Firmly push solution cover
on so it sits flush with top of
Battery. Let Battery sit for 1
hour before charging.
21) Charge the Battery at 1 or 2
Amps for 6 to 8 hours.
Install battery and fill the
motorcycle with oil.
22) Congratulations! You have just set up
a new Beta!
Follow the checklist on the customer’s
warranty registration card for a complete
pre-delivery inspection before delivery.
Altri manuali Beta Motociclo
Beta
Beta Rev 4T Manuale utente
Beta
Beta RR 4T-250 Manuale di istruzioni
Beta
Beta MINITRIAL LC Manuale utente
Beta
Beta RR 50 CC ENDURO Manuale utente
Beta
Beta REV 50 Manuale utente
Beta
Beta RR4T USA 400 Manuale utente
Beta
Beta RR 125 Manuale utente
Beta
Beta RR 125 cc Manuale utente
Beta
Beta evo 125SS 2022 Manuale utente
Beta
Beta EVO 2T 2010 Manuale utente
Beta
Beta EVO 4T 2011 Manuale utente
Beta
Beta Evo 80 Senior Manuale utente
Beta
Beta 2008 URBAN 125cc Manuale utente
Beta
Beta Evo4t 300 Manuale utente
Beta
Beta EVO 4T 2012 Manuale utente
Beta
Beta 125 RR-S 2020 Manuale utente
Beta
Beta Motard M4 Manuale utente
Beta
Beta RR 350 EFI Manuale utente
Beta
Beta X-Trainer 300 2T Manuale utente
Beta
Beta RR 50 cc ENDURO Manuale utente
