Biostar BIPV8M-IAE Guida utente
BIPV8M-IAE Setup Manual
FCC Information and Copyright
This equipment has been tested and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee
that interference will not occur in a particular installation.
The vendor makes no representations or warranties with respect to the
contents here and specially disclaims any implied warranties of merchantability
or fitness for any purpose. Further the vendor reserves the right to revise this
publication and to make changes to the contents here without obligation to
notify any party beforehand.
Duplication of this publication, in part or in whole, is not allowed without first
obtaining the vendor’s approval in writing.
The content of this user’s manual is subject to be changed without notice and
we will not be responsible for any mistakes found in this user’s manual. All the
brand and product names are trademarks of their respective companies.
Table of Contents
Chapter 1: Introduction ........................................ 3
1.1 Before You Start ................................................................................ 3
1.2 Package Checklist............................................................................. 3
1.3 Mainboard Specification................................................................... 4
1.4 Rear Panel.......................................................................................... 5
1.5 Mainboard Layout ............................................................................ 6
Chapter 2: Installation.......................................... 7
2.1 CPU...................................................................................................... 7
2.2 Fan Header......................................................................................... 7
2.3 System Memory.................................................................................. 8
2.4 Power Supply ..................................................................................... 9
2.5 Onboard Slot/Connector/Header/Jumper.................................... 10
Chapter 3: BIOS Setup ........................................ 21
3.1 Main Menu........................................................................................ 23
3.2 Advanced Menu............................................................................... 28
3.3 PCI/PnP Menu.................................................................................. 38
3.4 Boot Menu ........................................................................................ 41
3.5 Chipset Menu.................................................................................... 43
3.6 Exit Menu.......................................................................................... 48
Chapter 4: Useful Help ........................................ 51
4.1 Driver Installation Note.................................................................. 51
4.2 AMI BIOS Beep Code....................................................................... 52
4.3 Troubleshooting............................................................................... 53
BIPV8M-IAE
3
CHAPTER 1: INTRODUCTION
1.1 BEFORE YOU START
Thank you for choosing our product. Before you start installing the
mainboard, please make sure you follow the instructions below:
Prepare a dry and stable working environment with
sufficient lighting.
Always disconnect the system from power outlet
before operation.
Before you take the mainboard out from anti-static
bag, ground yourself properly by touching any safely
grounded appliance, or use grounded wrist strap to
remove the static charge.
Avoid touching the components on mainboard or the
rear side of the board unless necessary. Hold the board
on the edge, do not try to bend or flex the board.
Do not leave any unfastened small parts inside the
case after installation. Loose parts will cause short
circuits which may damage the equipment.
Keep the system from dangerous area, such as heat
source, humid air, and water.
Please switch on/off the machine normally. That is, DO
NOT pull out power cord directly from the mainboard
or the system may damage.
1.2 PACKAGE CHECKLIST
Mini-ITX Mainboard x 1
Fully Setup Driver CD x 1
I/O Bracket x 1
IDE Cable x 1 (Optional)
SATA Cable x 1 (Optional)
Mini-ITX Mainboard Manual
4
1.3 MAINBOARD SPECIFICATION
Specif ica tio n
CPU
Intel C PU On- board
Intel Atom D510 @1.67GHz dual core
Pineview-D Processor
FSB Supports up 667 MHz
Chipset Southbridge: ICH8M
Graphic Intel Pineview-D integrated graphics engine
Max Shared Video Memory is 384 MB
Supports dual displays (Extended mode)
as below:
—LVDS (Single channel, support up to
WXGA)
—RGB (Support up to SXGA+
2048x1536/60Hz)
Super I/O
ITE IT8718F
Provides the most commonly used legacy
Super I/O functionality.
128pin type
Enviro nment Co ntrol in it iat ives ,
H/W Monitor
Fan Speed Controller
Main
Memory
SO-DIMM (200pin) Slot x 1
Supports DDR2 667 / 800MHz
DIMM supports 256MB / 512MB / 1GB / 2GB
Max Memory Capacity 2GB
Registered DIMM or ECC DIMM is not
supported
IDE ICH8 M
Ultra DMA 33/66/100 Bus Master Mode
Supports PIO Mode 0~4
Supports 2 IDE devices
SATA ICH8M SATAII Vers ion 1.0a specif icat ion compliant
Data transfer rates up to 3.0 Gb/s
LAN Realtek RTL 8111DL x 2 10 / 100 / 1000 Mb/s auto negotiation
Ha lf / Fu ll dup lex capability
Sound
Codec
Realtek ALC662 5.1 channels audio out
High-Defin it ion Audio s uppo rt
PCI slot x1
Slot
Mini PCI-E Slot x1
IDE Connector x1
SATA2 Connector x2
Front Panel Header x1
Parallel Connector x1
On Board
Connectors
& Head ers
Digital I/O Connector x1
BIPV8M-IAE
5
Specif ica tio n
Fan He ad er x 1
Clear C MOS Header x1
AT/ATX Power Switch Header x1
USB 2.0 Header x2
LVDS Connector x1
LCD Power Select Header x1
LCD Backlight Power ON/OFF He ader x 1
LCD Backlight Inverter Connector x1
Inverter Power Select Header x1
Backlight Brightness Adjust Header x1
Serial Connectors (RS-232) x3
Power Connector for SATA x1
Power Connector (4pin) x1
Back Panel
I/O
PS/2 Keyboard x1
PS/2 Mouse x1
Serial Port x3
VGA Port x1
LAN port x2
USB Port x4
Audio Jack x3
2 x RS-232
1 x RS-232/422/485 by jumper (optional)
Board Size
170 mm (W) x 170 mm (L) Mini-ITX
OS
Support
Windows XP/XPE, Linux Biostar reserves the right to add or remove
support for any OS with or without notice.
1.4 REAR PANEL
PS/2
Mouse
PS/2
Keyboard
JCOM2
Mic In
(Center/SUB)
Line In
(Rear)
Line Out
(Front)
LAN
USB 2.0 x 4
JCOM1
LA N
VGA
JCOM3
Mini-ITX Mainboard Manual
6
1.5 MAINBOARD LAYOUT
JCOM2
JCO
M
1
JKBMS1
JCOM3
J
V
G
A
1
JUSBLAN1
JUSBLAN2
JAUDIO1
JATXPWR1
DIMMA1
JCOM6
JCOM5
JCOM4
LV DS -CONN1
JC1
JBL2 JBL1
JLV2
JLV1
JP2
JP3
JSEL2JSEL1
JPRNT1
PE1
PCI1
JDIO1
JPANEL1
USB1
USB2
BIOS
IDE 1
SATA1SATA2
JSFAN1
JHDD1
JCMOS1
JAT1
Intel
Atom
D510
CPU1
ICH8M
BAT1
Note: represents the 1■st pin.
BIPV8M-IAE
7
CHAPTER 2: INSTALLATION
2.1 CPU
The mainboard includes an embedded Intel Atom D510 processor, and a
heatsink has been installed to provide sufficient cooling.
2.2 FAN HEADER
The fan header supports cooling-fans built in the system. The fan cable
and connector may be different due to the fan manufacturer.
JSFAN1: System Fan Header
Pin Assignment
1 Ground
2 +12V
3 FAN RPM rate
sense
1
3
Note:
The System Fan Header supports 3-pin head connector. When connecting with wires
onto connectors, please note that the red wire is the positive and should be connected to
pin#2, and the black wire is Ground and should be connected to GND.
Mini-ITX Mainboard Manual
8
2.3 SYSTEM MEMORY
DIMMA1: Memory Module (200pin SO-DIMM)
2 Align a DIMM on the slot such that the notch on the DIMM matches the
break on the Slot.
3 Insert the DIMM firmly into the slot until the retaining chip snap back in
place and the DIMM is properly seated.
Memory Capacity
DIMM Socket Location DDR2 Module Total Memory Size
DIMMA1 256MB/512MB/1GB/2GB Max is 2GB.
BIPV8M-IAE
9
2.4 POWER SUPPLY
JATXPWR1: ATX Power Source Connector
This connector provides +12V to system power circuit.
Pin
Assignment
1 +12V
2 +12V
3 Ground
12
34
4 Ground
JHDD1: SATA Power Connector
This connector provides power connection of SATA devices.
Pin Assignment
1 +12V
2 GND
3 +3.3V
4 +5V
1
4
Mini-ITX Mainboard Manual
10
2.5 ONBOARD SLOT/CONNECTOR/HEADER/JUMPER
PCI1: Peripheral Component Interconnect Slot
This mainboard is equipped with 1 standard PCI slot. PCI stands for Peripheral
Component Interconnect, and it is a bus standard for expansion cards. This PCI
slot is designated as 32 bits.
PCI1
PE1: Mini PCI-E Slot
This mainboard is equipped with 1 Mini PCI-E Slot.
Indice
Altri manuali Biostar Scheda madre
Biostar
Biostar M7MKA Manuale utente
Biostar
Biostar B660MX-E Manuale utente
Biostar
Biostar M7 VKL Manuale utente
Biostar
Biostar M7 VKQ Manuale utente
Biostar
Biostar P4 SFA Guida utente
Biostar
Biostar A520MH Manuale utente
Biostar
Biostar M7VKF Manuale utente
Biostar
Biostar M5SAA Manuale utente
Biostar
Biostar TZ77A Guida utente
Biostar
Biostar TA790GX A3+ Manuale
Biostar
Biostar Hi-Fi Z97Z7 Guida utente
Biostar
Biostar X470NH Manuale utente
Biostar
Biostar TA75M+ Guida utente
Biostar
Biostar H310MHP 3.0 Manuale utente
Biostar
Biostar G31-M4 Manuale utente
Biostar
Biostar P4M900-M4 Guida utente
Biostar
Biostar 945G Micro 775 TE Guida utente
Biostar
Biostar IDEQ 200V Guida utente
Biostar
Biostar H81M-IDE Guida utente
Biostar
Biostar Z170GT7 Manuale utente
Manuali Scheda madre popolari di altre marche
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manuale utente
Gigabyte
Gigabyte GA-9IVDT Manuale utente
Texas Instruments
Texas Instruments ADS8372EVM Manuale utente
Commell
Commell MS-C73 Manuale utente
IBT Technologies
IBT Technologies MB860 Manuale utente
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manuale utente
