Black Box SW1007A Manuale utente
FIBER OPTIC A/B/C SWITCH
(Non-latching)
JANUARY 2008
Model# SW1007A
CUSTOMER
SUPPORT
INFORMATION
Order toll-free in the U.S.: 877-877-BBOX (outside U.S. call 724-746-5500)
FREE technical support, 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-
746-0746
Mail order: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018
Page 2
Fiber Optic A/B/C Switch (non-latching)
FEDERAL COMMUNICATIONS COMMISSION
AND
INDUSTRY CANADA
RADIO FREQUENCY INTERFERENCE STATEMENTS
This equipment generates, uses, and can radiate radio-frequency energy, and
if not installed and used properly, that is, in strict accordance with the
manufacturer’s instructions, may cause interference to radio communication.
It has been tested and found to comply with the limits for a Class A
computing device in accordance with the specifications in Subpart B of Part
15 of FCC rules, which are designed to provide reasonable protection
against such interference when the equipment is operated in a commercial
environment. Operation of this equipment in a residential area is likely to
cause interference, in which case the user at his own expense will be
required to take whatever measures may be necessary to correct the
interference.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This digital apparatus does not exceed the Class A limits for radio noise
emission from digital apparatus set out in the Radio Interference Regulation
of Industry Canada.
Le présent appareil numérique n’émet pas de bruits radioélectriques
dépassant les limites applicables aux appareils numériques de la classe A
prescrites dans le Règlement sur le brouillage radioélectrique publié par le
Industrie Canada.
FCC STATEMENT
Page 3
Fiber Optic A/B/C Switch (non-latching)
Contents
Chapter Page
1. Specifications …………………………………... 4
2. Introduction …………………………………. 5
3. Installation …………………………………….. 6
4. Troubleshooting ……………………………….. 6
CONTENTS
Page 4
Fiber Optic A/B/C Switch (non-latching)
Specifications
Connectors
(4 pairs) ST, (1) 3.5-mm power input
Also available with SC connectors—please call!
Data Rates
Transparent to signal rates, wavelengths, & formats
Switching Speed
less than 1 sec typical
Sensitivity
750 to 1450 nanometers
Optical Loss
less than 3.0 dB typical per FOTP-171 method B1
Compatibility
62.5/125 µm multimode fiber
Crosstalk
less than -45 dB typical per FOTP-42
Grounding
None required
Approvals
UL , CE and PSE (power supply)
Operating Temperature
14 to 149ºF (-10 to +65ºC)
Relative Humidity Tolerance
10 to 95%, non-condensing
Chapter 1: Specifications
Page 5
Fiber Optic A/B/C Switch (non-latching)
Mean Time Between Failures
100,000 hours or 1,000,000 cycles
Power
100-240 VAC 50/60 Hz wall-mount PSU, 5 VDC out
Size
2.5”H x 8”W x 6.3”D (6.4 x 20.3 x 16 cm)
Weight
3 lb. (1.8 kg)
Introduction
The non-latching Fiber Optic A/B/C Switch is a full-
duplex, optical 3 port switch. It can be used to connect one
workstation to three different networks (one at a time) or
to other remote devices. A front panel rotary style knob
allows the user to select which of three ports (A, B or C) is
connected to the “COMMON” port on the switch. The
switch operates using a unique all-optical micro-mirror
movement. When you turn the rotary knob on the front of
the switch to select a network, the internal micro-mirror
movement redirects the optical beam from one network
port to the other network port by rotating a miniature
mirror. This technique eliminates the need to convert
optical signals to electronic signals to for switching and it
is therefore transparent to data rates and protocols.
This switch is perfectly suited for use as a fall-back switch
when a pre-determined connection is desired in the event
of a power failure. You should use a latching fiber optic
switch like Model # SW1004A for applications requiring a
switch that maintains the selected connection during the
loss of AC power. Latching switches use power only for
switching to the selected connection. No power is required
to pass data through the switches.
Chapter 2: Introduction
Page 6
Fiber Optic A/B/C Switch (non-latching)
Installation
Place the switch in a convenient stable location and
connect the power supply unit to a reliable source of AC
power that meets the requirements shown in the
Specifications section of this manual.
This switch is ideal for use in fall-back applications
where a pre-determined connection is desirable in the
event of a power failure. Connect the two fiber leads
from the device to be shared to the switch port labeled
common. Connect the A port to the network or device to
which you want to be connected if power is lost. Connect
the remaining networks or devices to the ports labeled
B and C.
Your installation of this switch is now complete.
Troubleshooting
If the Fiber Optic A/B/C Switch fails to operate, check
the following before calling for technical support.
1. Ensure that the power supply connected to a power
source and to the switch.
2. Check the fiber optic connectors for proper
connections to the correct ports of the switch.
3. Operate the switch knob to verify that it’s tightly
secured to the switch shaft and does not spin loosely.
4. Verify the integrity of the fiber optic leads by
replacing a suspect lead with a spare.
Chapter 3: Installation
Chapter 4: Troubleshooting
Page 7
Fiber Optic A/B/C Switch (non-latching)
Notes:
© Copyright 2007 Black Box Corporation. All rights reserved.
1000 Park Drive • Lawrence, PA 15055-1018 • 724-746-5500 • Fax 724-746-0746
Indice
Altri manuali Black Box Interruttore
Black Box
Black Box SW135A Manuale utente
Black Box
Black Box LPB208A-R2 Manuale utente
Black Box
Black Box KVS4-4004DHVX Manuale utente
Black Box
Black Box LE2650A Manuale utente
Black Box
Black Box LH8050A Manuale utente
Black Box
Black Box SW1046A Manuale utente
Black Box
Black Box KV6224DPH Manuale utente
Black Box
Black Box LB9902A Manuale utente
Black Box
Black Box SW177A Manuale utente
Black Box
Black Box LPB5028A Manuale utente
Black Box
Black Box KVM2016A Manuale utente
Black Box
Black Box ServSwitch DTX5000 Manuale utente
Black Box
Black Box ServSwitch Wizard DVI KV1002A Manuale utente
Black Box
Black Box LGB5510A Manuale di programmazione
Black Box
Black Box KV9104A Manuale utente
Black Box
Black Box ServSwitch 4site II Manuale utente
Black Box
Black Box KV6222H Manuale utente
Black Box
Black Box ServShare II KV421A Manuale utente
Black Box
Black Box LPB2810A Manuale utente
Black Box
Black Box PS/2 Manuale utente
