Black Box SW1033A Manuale utente
SINGLE MODE
FIBER OPTIC A/B SWITCH
(Non-latching)
September 2008
Mode # SW1033A
Mode # SW1034A
CUSTOMER
SUPPORT
INFORMATION
Order toll-free in the U.S.: 877-877-BBOX (outside U.S. call 724-74 -5500)
FREE technical support, 24 hours a day, 7 days a week: Call 724-74 -5500 or
fax 724-74 -074
Mail order: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018
Web site: www.blackbox.com • E-mail: [email protected]m
Page 2
Sing e Mode Fiber Optic A/B Switch (NL)
Contents
Chapter Page
1. Specifications …………………………………... 4
2. Introduction …………………………………. 5
3. Installation …………………………………….. 6
4. Troubleshooting ……………………………….. 6
CONTENTS
Page 3
Sing e Mode Fiber Optic A/B Switch (NL)
Specifications
Connectors
S 1033A - (3 pairs) ST connectors, 3.5-mm power input
S 1034A - (3 pairs) SC connectors, 3.5-mm power input
Data Rates
Transparent to signal rates, wavelengths, & formats
Switching Speed
less than 10 ms typical
Sensitivity
1310 /1550 nanometers
Optical Loss
less than 2.0 dB typical
Compatibility
8 to 10um Single mode fiber
Crosstalk
less than –55 dB typical
Approvals
UL , CE and PSE (power supply)
Operating Temperature
14 to 149ºF (-10 to +65ºC)
Relative Humidity Tolerance
10 to 95%, non-condensing
ean Time Between Failures
100,000 hours or 10,000,000 cycles
Chapter 1: Specifications
Page 4
Sing e Mode Fiber Optic A/B Switch (NL)
Power
100-240 VAC 50/60 Hz wall-mount PSU, 5 VDC out
Size
2.5”H x 8” x 6.3”D (6.4 x 20.3 x 16 cm)
Weight
3 lb. (1.8 kg)
Introduction
The non-latching Single Mode Fiber Optic A/B Switch is a
full-duplex, optical 2 port switch. It can be used to connect
one workstation to two different networks (one at a time)
or to other remote devices. A front panel rotary style knob
allows the user to select which of two ports (A or B) is
connected to the C port on the switch. The switch operates
using a unique all-optical micro-mirror movement. hen
you turn the rotary knob on the front of the switch to select
a network, the internal micro-mirror movement redirects
the optical beam from one network port to the other
network port by rotating a miniature mirror. This
technique eliminates the need to convert optical signals to
electronic signals to for switching and it is therefore
transparent to data rates and protocols.
This switch is perfectly suited for use as a fall-back switch
when a pre-determined connection is desired in the event
of a power failure. You should use a latching fiber optic
switch like Model S 1035A for applications requiring a
switch that maintains the selected connection during the
loss of AC power. Latching switches use power only for
switching to the selected connection. No power is required
to pass data through the switches.
Chapter 2: Introduction
Page 5
Sing e Mode Fiber Optic A/B Switch (NL)
Insta ation
Place the switch in a convenient stable location and
connect the power supply unit to a reliable source of AC
power that meets the requirements shown in the
Specifications section of this manual.
This switch is ideal for use in fall-back applications
where a pre-determined connection is desirable in the
event of a power failure. Connect the two fiber leads
from the device to be shared to the switch port labeled C.
Connect the A port to the network or device to which you
want to be connected if power is lost. Connect the
remaining network or device to port B of the switch.
Your installation of this switch is now complete.
Troub eshooting
If the Fiber Optic A/B Switch fails to operate, check the
following before calling for technical support.
1. Ensure that the power supply connected to a power
source and to the switch.
2. Check the fiber optic connectors for proper
connections to the correct ports of the switch.
3. Operate the switch knob to verify that it’s tightly
secured to the switch shaft and does not spin loosely.
4. Verify the integrity of the fiber optic leads by
replacing a suspect lead with a spare.
Chapter 3: Insta ation
Chapter 4: Troub eshooting
© Copyright 2008 Black Box Corporation. All rights reserved.
1000 Park Drive • Lawrence, PA 15055-1018 • 724-746-5500 • Fax 724-746-0746
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Black Box Interruttore
Black Box
Black Box LB9020A Manuale utente
Black Box
Black Box ServSwitch DTX5002 Manuale utente
Black Box
Black Box SWI083A Manuale utente
Black Box
Black Box LB620C Manuale utente
Black Box
Black Box ServSwitch Wizard SW652A Manuale utente
Black Box
Black Box ServSwitch Octet KV1701 Manuale utente
Black Box
Black Box LH8050A Manuale utente
Black Box
Black Box SW925A Manuale utente
Black Box
Black Box ET0100A Manuale utente
Black Box
Black Box High-Speed SME V.35-M34 Manuale utente
Black Box
Black Box 12-Port 1000BASE-TX L2 Managed PoE Switch Manuale utente
Black Box
Black Box MT136A Manuale utente
Black Box
Black Box LGH1000 Series Manuale utente
Black Box
Black Box LIG401A Manuale utente
Black Box
Black Box LPJ008A-T-R2 Manuale utente
Black Box
Black Box LB9801A Manuale utente
Black Box
Black Box LB9217A-R2 Manuale utente
Black Box
Black Box KV2004A Manuale utente
Black Box
Black Box ServSelect III KV21008A Manuale utente
Black Box
Black Box PCA45A Manuale utente
