Black Box SW1035A Manuale utente

SINGLE MODE

FIBER OPTIC A/B SWITCH

(LATCHING)

SEPTEMBER 2008

Model# SW1035A

Model# SW1036A

CUSTOMER

SUPPORT

INFORMATION

Order toll-free in the U.S.: 877-877-BBOX (outside U.S. call 724-746-5500)

FREE technical support, 24 hours a day, 7 days a week: Call 724-746-5500 or

fax 724-746-0746

Mail order: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018

Web site: www.blackbox.com • E-mail: [email protected]

Page 2

Single Mode Fiber Optic A/B Switch (latching)

FEDERAL COMMUNICATIONS COMMISSION

AND

INDUSTRY CANADA

RADIO FREQUENCY INTERFERENCE STATEMENTS

This equipment generates, uses, and can radiate radio-frequency energy, and

if not installed and used properly, that is, in strict accordance with the

manufacturer’s instructions, may cause interference to radio communication.

It has been tested and found to comply with the limits for a Class A

computing device in accordance with the specifications in Subpart B of Part

15 of FCC rules, which are designed to provide reasonable protection

against such interference when the equipment is operated in a commercial

environment. Operation of this equipment in a residential area is likely to

cause interference, in which case the user at his own expense will be

required to take whatever measures may be necessary to correct the

interference.

Changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

This digital apparatus does not exceed the Class A limits for radio noise

emission from digital apparatus set out in the Radio Interference Regulation

of Industry Canada.

Le présent appareil numérique n’émet pas de bruits radioélectriques

dépassant les limites applicables aux appareils numériques de la classe A

prescrites dans le Règlement sur le brouillage radioélectrique publié par le

Industrie Canada.

FCC STATEMENT

Page 3

Single Mode Fiber Optic A/B Switch (latching)

Contents

Chapter Page

1. Specifications …………………………………... 4

2. Introduction …………………………………. 5

3. Installation …………………………………….. 6

4. Troubleshooting ……………………………….. 6

CONTENTS

Page 4

Single Mode Fiber Optic A/B Switch (latching)

Specifications

Connectors

(3 pairs) ST connectors, (1) 3.5-mm power input

(SW1035A)

(3 pairs) SC connectors, (1) 3.5-mm power input

(SW1036A)

Data Rates

Transparent to signal rates, wavelengths, & formats

Switching Speed

less than 10 ms typical

Sensitivity

1310 / 1550 nanometers

Optical Loss

less than 2.0 dB typical

Compatibility

8 to 10um Single mode fiber

Crosstalk

less than -55 dB typical per FOTP-42

Approvals

UL, CE, and PSE (power supply)

Operating Temperature

14 to 149ºF (-10 to +65ºC)

Relative Humidity Tolerance

10 to 95%, non-condensing

Chapter 1: Specifications

Page 5

Single Mode Fiber Optic A/B Switch (latching)

Mean Time Between Failures

100,000 hours or 10,000,000 cycles

Power

100-240 VAC 50/60 Hz wall-mount PSU, 12 VDC out

Size

2.5”H x 8”W x 6.3”D (6.4 x 20.3 x 16 cm)

Weight

4 lb. (1.8 kg)

Introduction

The Single Mode latching Fiber Optic A/B Switch is a

full-duplex, optical 2 port switch. It can be used to connect

one workstation to two different networks (one at a time)

or to other remote devices. A front panel rotary style knob

allows the user to select which of two ports (A or B) is

connected to the COMMON (C) port on the switch. The

switch operates using a unique all-optical micro-mirror

movement. When you turn the rotary knob on the front of

the switch to select a network, the internal micro-mirror

movement redirects the optical beam from one network

port to another network port by rotating a miniature mirror.

This technique eliminates the need to convert optical

signals to electronic signals for switching and is therefore

transparent to data rates and protocols.

This switch is perfectly suited for applications where a

selected connection must be maintained in the event of a

power failure. You should use a non-latching fiber optic

switch for applications requiring a switch that falls back to

pre-determined connection during the loss of AC power

(please call us). These switches use power only for

switching the selected connection. No power is required to

pass data through the switches.

Chapter 2: Introduction

Page 6

Single Mode Fiber Optic A/B Switch (latching)

Installation

Place the switch in a convenient stable location and

connect the power supply unit to a reliable source of AC

power that meets the requirements shown in the

Specifications section of this manual. Then change the

front panel rotary knob to switch between the different

connection states to insure that the latching fiber optic

switch modules are in a known position before

connecting the switch to your fiber optic devices.

Connect the two fiber leads from the device to be shared

to the common switch port labeled C. Connect the

networks or other devices to the user selectable output

ports labeled A and B.

Your installation of this switch is now complete.

Troubleshooting

If the Fiber Optic A/B Switch fails to operate, check the

following before calling for technical support.

1. Ensure that the power supply connected to a power

source and to the switch.

2. Check the fiber optic connectors for proper

connections to the correct ports of the switch.

3. Operate the switch knob to verify that it’s tightly

secured to the switch shaft and does not spin loosely.

4. Verify the integrity of the fiber optic leads by

replacing a suspect lead with a spare.

Chapter 3: Installation

Chapter 4: Troubleshooting

Page 7

Single Mode Fiber Optic A/B Switch (latching)

Notes:

1000 Park Drive • Lawrence, PA 15055-1018 • 724-746-5500 • Fax 724-746-0746

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Black Box Interruttore

Black Box

Black Box LPB2810A Manuale utente

Black Box

Black Box KV6108SA-R2 Manuale utente

Black Box

Black Box LGB5510A Manuale di programmazione

Black Box

Black Box LB9019A-R3 Manuale utente

Black Box

Black Box KV2004A Manuale utente

Black Box

Black Box VSW-HDMI2-3X1 Manuale utente

Black Box

Black Box DCX3000 Manuale utente

Black Box

Black Box INTEL EXPRESS 410T Scheda tecnica

Black Box

Black Box KV9104A Manuale utente

Black Box

Black Box IC147A Manuale utente

Black Box

Black Box EMS1G-48 Manuale

Black Box

Black Box SW202A Manuale utente

Black Box

Black Box IC254A-US Manuale utente

Black Box

Black Box KVIP1016A Manuale utente

Black Box

Black Box EMERALD EMD200DP-T Manuale utente

Black Box

Black Box Switch Manuale utente

Black Box

Black Box LGS103AE Manuale utente

Black Box

Black Box SW214A Manuale utente

Black Box

Black Box SERVSWITCH KV3108SA-R4 Manuale utente

Black Box

Black Box IC147A-R2 Manuale utente

Black Box

Black Box ServSwitch SW625A-R2 Manuale utente

Black Box

Black Box LGB2118A Guida utente

Black Box

Black Box IC147A-R3 Manuale utente

Black Box

Black Box ServSwitch KV0004A Manuale utente

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente