Black Box IC447A Manuale utente
CUSTOMER
SUPPORT
INFORMATION
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)
FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746
Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018
DECEMBER 2002
IC447A
S-Video Balun
1
FCC/IC RFI STATEMENTS, TRADEMARKS
FEDERAL COMMUNICATIONS COMMISSION AND INDUSTRY CANADA
RADIO-FREQUENCY INTERFERENCE STATEMENTS
Class B Digital Device. This equipment has been tested and found to comply with the
limits for a Class B computing device pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or telephone reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult an experienced radio/TV technician for help.
Caution: Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
To meet FCC requirements, shielded cables are required to connect this device to
other Class B certified devices.
This digital apparatus does not exceed the Class B limits for radio noise emission from digital
apparatus set out in the Radio Interference Regulation of Industry Canada.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites
applicables aux appareils numériques de classe B prescrites dans le Règlement sur le brouillage
radioélectrique publié par Industrie Canada.
TRADEMARKS USED IN THIS MANUAL
BLACK BOX and the logo are registered trademarks of Black Box
Corporation.
Any other trademarks mentioned in this manual are acknowledged to be the property of the
trademark owners.
2
S-VIDEO BALUN
NORMAS OFICIALES MEXICANAS (NOM)
ELECTRICAL SAFETY STATEMENT
INSTRUCCIONES DE SEGURIDAD
1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de
que el aparato eléctrico sea operado.
2. Las instrucciones de seguridad y operación deberán ser guardadas para
referencia futura.
3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de
operación deben ser respetadas.
4. Todas las instrucciones de operación y uso deben ser seguidas.
5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca
de la tina de baño, lavabo, sótano mojado o cerca de una alberca, etc..
6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que
sean recomendados por el fabricante.
7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea
recomendado por el fabricante.
8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá
a lo descrito en las instrucciones de operación. Todo otro servicio deberá ser
referido a personal de servicio calificado.
9. El aparato eléctrico debe ser situado de tal manera que su posición no
interfiera su uso. La colocación del aparato eléctrico sobre una cama, sofá,
alfombra o superficie similar puede bloquea la ventilación, no se debe colocar
en libreros o gabinetes que impidan el flujo de aire por los orificios de
ventilación.
10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor
como radiadores, registros de calor, estufas u otros aparatos (incluyendo
amplificadores) que producen calor.
11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del
tipo descrito en el instructivo de operación, o como se indique en el aparato.
3
NOM STATEMENT
12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización
del equipo no sea eliminada.
13. Los cables de la fuente de poder deben ser guiados de tal manera que no
sean pisados ni pellizcados por objetos colocados sobre o contra ellos,
poniendo particular atención a los contactos y receptáculos donde salen del
aparato.
14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las
recomendaciones del fabricante.
15. En caso de existir, una antena externa deberá ser localizada lejos de las lineas
de energia.
16. El cable de corriente deberá ser desconectado del cuando el equipo no sea
usado por un largo periodo de tiempo.
17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean
derramados sobre la cubierta u orificios de ventilación.
18. Servicio por personal calificado deberá ser provisto cuando:
A: El cable de poder o el contacto ha sido dañado; u
B: Objectos han caído o líquido ha sido derramado dentro del aparato; o
C: El aparato ha sido expuesto a la lluvia; o
D: El aparato parece no operar normalmente o muestra un cambio en su
desempeño; o
E: El aparato ha sido tirado o su cubierta ha sido dañada.
4
S-VIDEO BALUN
Contents
Chapter Page
1. Specifications ............................................................................................. 5
2. Introduction ............................................................................................... 7
3. Installation .................................................................................................. 8
4. Troubleshooting ...................................................................................... 10
4.1 Things to Try If Problems Occur ..................................................... 10
4.2 Calling Black Box .............................................................................. 11
4.3 Shipping and Packaging ................................................................... 11
5
CHAPTER 1: Specifications
1. Specifications
Cable Required: Between balun pairs: Unshielded twisted pair (UTP):
Construction standard: Category 5;
Gauge: 24 AWG or lower;
Core: Solid;
Termination: RJ-45 plugs;
Pairs: 2 or more (4 wires used);
Impedance: 100 ohms at 1 MHz;
Maximum capacitance: 20 pF/ft. (6.1 pF/m);
Maximum attenuation: 6.6 dB/1000 ft. (2 dB/km) at
1 MHz;
To attached devices: Balun normally attaches directly to
equipment; if cable must be used, it must be standard
75-ohm S-Video cable with a 4-pin mini-DIN female
connector on the balun end
Compliance: FCC Class B, IC Class/classe B;
CISPR Pub. 22 Class B
Transmission: Transparent to users (automatic, no delay)
Impedance: S-Video side: 75 ohms;
UTP side: 100 ohms
Video Bandwidth: DC to 6 MHz
Maximum
Input: 1.1 volts peak-to-peak
Insertion Loss: Less than 2 dB per pair over the DC-to-6-MHz frequency
range
Return Loss: Greater than 15 dB over the DC-to-6-MHz frequency range
Common-Mode
Rejection: Greater than 40 dB over the DC-to-6-MHz frequency range
Maximum
Distance: 1000 ft. (304.8 m) of CAT5 cabling between baluns
Connectors: (1) RJ-45 female, (1) 4-pin mini-DIN male
6
S-VIDEO BALUN
RJ-45 Pins Used: 4 (C/chrominance ring), 5 (C/chrominance tip),
7 (Y/luminance ring), and 8 (Y/luminance tip); polarity-
sensitive (not autosensing or autocorrecting)
Temperature
Tolerance: Operating: 32 to 131˚F (0 to 55˚C);
Storage: -4 to +185˚F (-20 to +85˚C)
Humidity
Tolerance: Up to 95% noncondensing
Enclosure: Fire-retardant plastic
Size: 1"H x 1"W x 1.9"D (2.5 x 2.5 x 4.8 cm), with a nondetachable
5" (12.7-cm) S-Video cord
Weight: 1 oz. (28 g)
7
CHAPTER 2: Introduction
2. Introduction
With pairs of S-Video Baluns, you can transmit a single S-Video signal point-to-
point across Category 5 unshielded twisted-pair (UTP) cable, which is already
wired into most commercial sites. The balun near the video source takes a single
S-Video signal from the source, converts it, and transmits it over UTP cable to the
other balun, which outputs it to its destination. This lets you place or move your
S-Video equipment anywhere you have a modular wall outlet.
The S-Video Balun is designed for use with modular equipment and flexible
configurations. Compatible devices include S-Video video cameras and monitors,
DVD and videocassette players and recorders, video and LCD projectors, CCD
cameras, video switchers, sequencers, multiplexors, and other S-Video equipment.
Applications include classroom video distribution, overhead projector systems,
computer-training systems, and tradeshow computer-demo systems.
These baluns must be used in pairs.
8
S-VIDEO BALUN
3. Installation
To install a pair of S-Video Baluns, follow the steps below.
CAUTION!
Do not attempt to open the housings of the S-Video Baluns. There are
no user-serviceable parts inside.
1. Make sure that the video-destination device is not too far away from the video-
source device (refer to the Maximum Distance specification in Chapter 1). If
the destination device is beyond the reach of the source balun, the video
signal the device receives will be weak or nonexistent.
2. Follow the manufacturer’s instructions for turning off power to the video
equipment you will be attaching, and for disconnecting that equipment from
AC power and from all other devices.
3. Make certain that the modular outlets and cross-connects to which you will
connect the baluns are configured properly and are labeled so that the circuit
can be identified.
CAUTION!
Do not connect the S-Video Balun to a telecommunication outlet wired
to unrelated equipment. Making such a connection may damage the
equipment and/or the balun. Make sure that all wiring is straight-
through-pinned.
4. Verify that the twisted-pair circuit you want to use is not already being used
for other LAN or telephone equipment.
5. For each balun—depending on what type of equipment you are attaching it
to—either plug the 4-pin mini-DIN male connector at the end of its S-Video
cord directly into the device’s 4-pin mini-DIN female S-Video connector, or
plug the balun into an S-Video cable with 4-pin mini-DIN connectors that
runs to the device.
9
CHAPTER 3: Installation
6. Connect one end of a UTP cable to each balun’s RJ-45 modular jack, as
shown in Figure 3-1. These cables must carry at least two wire pairs; these
wires must be on RJ-45 Pins 4 (C/chrominance ring), 5 (C/chrominance tip),
7 (Y/luminance ring), and 8 (Y/luminance tip).
Figure 3-1. Attaching UTP cable to the balun.
7. Plug or hardwire the other end of each UTP cable into the appropriate video
wall outlet or patch panel. When this is done, a complete cabling circuit
should run between the two baluns, as shown in Figure 3-2.
Figure 3-2. Two baluns cabled together (not to scale).
8. Reconnect and power up the video equipment. Adjust the image settings of
any attached monitor or projector as necessary.
Your balun system should be ready for continuous operation.
Category 5 UTP
S-Video Balun
Instructor’s laptop
computer with
S-Video output
Auditorium
video projector with
S-Video input
S-Video Balun
Indice
Altri manuali Black Box Trasmettitore
Black Box
Black Box IC564A Manuale utente
Black Box
Black Box AC504A-WP Manuale utente
Black Box
Black Box Agility Zero-U ACR500DP-T Manuale utente
Black Box
Black Box FiberPath AC444A Manuale utente
Black Box
Black Box Agility Zero-U ACR500DP-T Manuale utente
Black Box
Black Box ME806A Manuale utente
Black Box
Black Box AC560A Manuale utente
Black Box
Black Box AC1003A-R2 Manuale utente
Black Box
Black Box AC603A Manuale utente
Black Box
Black Box ACR500HDMI-T Manuale utente
Black Box
Black Box VX-1002-TX Manuale utente
Black Box
Black Box IC565A Manuale utente
Black Box
Black Box IC449A Manuale utente
Black Box
Black Box AC3000A Manuale utente
Black Box
Black Box InvisaPC Manuale utente
Black Box
Black Box AC1003A-R2 Manuale utente
Black Box
Black Box VX-HDMI-HDIP-TX Manuale utente
Black Box
Black Box Quad Audio Balun Manuale utente
Black Box
Black Box InvisaPC DTX1000-T Manuale utente
Black Box
Black Box HD View AC3000A-R2 Series Manuale utente
