Blastrac EBE 500 S Manuale utente

Operating Instructions

EBE 500 S

MAN-EBE 500S-EN

Technical data

Safety instructions

General

Transport

Initial operation

Operation

Maintenance

Electrical & hydraulic systems

Fault diagnosis

Spare parts

Design and specifications are subject to

change without notice - Oktober 2002

ISPC Blastrac/EBE

Utrechthaven 12

3433 PN Nieuwegein

THE NETHERLANDS

T +31(0)30 - 601 88 66

F +31(0)30 - 601 83 33

E [email protected]

I www.surfacepreparation.com

Nieuwegein

EBE 500 S Operating Instructions

Technical data

Contents Chapter 1

1.1 Rating

1.2 Unit specifications

1.3 Operative range and correct usage

1.4 Stand-by power supply (generator 60 Hz)

1.5 Machine type designation

1.6 Advice for operators of blast cleaning machines

Operating Instructions EBE 500 S

Technical data

1.1 Rating

Unit / designation : ISPC Blastrac/EBE blast cleaning

machine

Machine type : EBE 500 S

Manufacturer : ISPC Blastrac/EBE

Utrechthaven 12

NL-3433PN Nieuwegein

THE NETHERLANDS

1.2 Unit specifications

Dimensions:

Machine

EBE 500 S

Length 1750 mm

Width 750 mm

Height 1650 mm

Weight ca.650 kg

Connected loads (electrical system):

The indicated input current values correspond to the nominal current

values of the motors working under full load. These values are not

achieved under normal operating conditions.

Power consumption Input current

EBE 500 S Blast

wheel drive

18.2 kW max. 35 A

Fan motor 2.2 kW max. 4.6 A

Hydr. pump motor 2.2 kW max. 5.2 A

Electrical connection required : 400-480 V, 60 Hz, 63 A

EBE 500 S Operating Instructions

Technical data

Rated speed Enclosure

Drive of blast wheel 3480 min-1 (60Hz) IP 55

Fan motor 3430 min-1 (60Hz) IP 55

Hydr. pump motor 1695 min-1 (60Hz) IP 55

Blast wheel size : 349 mm Ø

Working width : 500 mm

Drive speed : 0 - 30 m/min

Blast cleaning output on steel : up to 75 m²/h

Blast cleaning output on concrete : up to 150 m²/h

Dust hose connection : 150 mm Ø

Recommended abrasive : Shot 390-460 / SG18-16-14

Abrasive consumption : 0,1 - 0,5 kg/m²

Recommended filter unit : EBE 500 DAAM

1.3 Operative range and correct usage

The EBE 500 S is exclusively designed to clean dry,

frost-free horizontal surfaces. The machine may not

be used for other purposes. The manufacturer will

not be liable for damage resulting from such

incorrect usage. In these cases the user assumes all

risks.

Operating Instructions EBE 500 S

Technical data

1.4 Stand-by power supply (generator 60 Hz)

If the EBE 500 S blast cleaning machine is operated

using a 60 Hz generator, this generator must be

operated in accordance with the current VDE

directives (this applies to the protective earth

conductor in particular) in order to ensure that all

safety devices are functioning and to eliminate

possible damage to electrical components.

1.5 Machine type designation

product typ

blast cleaning widt

product cod

EBE 500 S

1.6 Advise for operators of blast cleaning machines

In accordance with the accident prevention

regulations for blast cleaning work (VBG 48) the

operator must provide operating instructions for

blast cleaning work in a form and language that is

understandable.

The blast cleaning machine Operating Instructions

are only part of these operating instructions. Please

consult the current accident prevention regulations

for the precise content.

EBE 500 S Operating Instructions

Safety instructions

Contents Chapter 2

2.0 Warnings and symbols

2.1 Organisational measures

2.2 Personnel selection and qualification

2.3 Safety precautions applicable to different operating conditions

2.4 Special work within the scope of use of the equipment and

maintenance activities as well as repairs during operation

2.5 Definition of the Safety off position

2.6 Particular dangerous aspects of the equipment

2.7 Electrical engineering regulations

Operating Instructions EBE 500 S

Safety instructions

2.0 Warnings and symbols

The following denominations and symbols are used in the Operating

Instructions to highlight areas of particular importance:

Symbol of operational safety.

In these Operating Instructions this symbol will be

shown next to all safety precautions that are to be

taken in order to ensure prevention to life and injury.

Follow these instructions and take special care in

these circumstances. In addition to these

instructions, the general safety precautions and

accident prevention guidelines are also to be

followed.

Particular details regarding the economical use of

the equipment.

Information, instructions and restrictions with regard

to possible risks to persons or to extensive material

damages.

EBE 500 S Operating Instructions

Safety instructions

Warning against dangerous voltages.

Indications relating to protective devices in electrical

appliances.

Indications where consultation with the

manufacturer is required.

Instructions relating to periodical checks.

Reference to important instructions contained in the

Operating Instructions.

2.1 Organisational measures

The Operating Instructions are to be kept near the location

where the machine is located and must be within reach at all

times!

In addition to the Operating Instructions general and legal regulations

regarding accident prevention and environmental protection must be

complied with and indicated!

Such duties may for example relate to the handling of hazardous

substances or to the provision and wearing of personal protection

equipment as well as compliance with traffic regulations.

Operating Instructions EBE 500 S

Safety instructions

The Operating Instructions must be supplemented by instructions

including the duty to supervise and report relating to particular

working practices, for example work organisation, work procedures

and personnel allocation.

Personnel entrusted with working with the machine must have read

the Operating Instructions before starting work, in particular the

Safety Instructions chapter. To read these instructions during work

is too late. This particularly applies to incidental activities such as

setting up the equipment, carrying out maintenance work or training

staff to work with the machine.

From time to time the working practices of the staff are to be checked

regarding awareness of safety and hazards.

Personnel must tie back long hair and not wear loose clothing or

jewellery including rings. There is a risk of injury through getting stuck

or being drawn into moving machinery.

Use personnel protection equipment if necessary or required by

regulations! Take notice of all safety and hazard notices on the

machine!

All safety and hazard notices at or on the machine must be kept

complete and legible!

If safety-critical changes occur to the machine or its working

method, the machine must be shut down immediately! The cause of

the fault must be established immediately!

Changes, add-ons or conversions to the machine which might impair

safety must not be undertaken without the manufacturer’s

permission!

This applies in particular to the fitting and adjustment of safety

devices as well as to welding on load-bearing parts.

Spare parts must comply with the technical requirements specified

by the manufacturer. This is always guaranteed if original spare

parts are used.

Intervals for recurring checks and inspections specified in these

Operating Instructions must be complied with!

Indice

Altri manuali Blastrac Attrezzature industriali

Blastrac

Blastrac BDC-66 Manuale utente

Blastrac

Blastrac 125 BDC1216 Manuale utente

Blastrac

Blastrac BMP-4000E Manuale utente

Blastrac

Blastrac BMP-400RC Manuale utente

Blastrac

Blastrac 1-7D Manuale utente

Blastrac

Blastrac 500HSH Manuale utente

Blastrac

Blastrac 854 DCS Manuale utente

Blastrac

Blastrac BMC-335 ELITE RC Manuale utente

Blastrac

Blastrac BMS-150 Manuale utente

Blastrac

Blastrac 200VMB Manuale utente

Blastrac

Blastrac 2-20DT Manuale utente

Blastrac

Blastrac BDC-655 EX Manuale utente

Blastrac

Blastrac 1-10DPS75 MKII Manuale utente

Blastrac

Blastrac 1-8DEZ Manuale utente

Blastrac

Blastrac BMP-335 Manuale utente

Blastrac

Blastrac 2-48DS Manuale utente

Blastrac

Blastrac 1-10DS Global Manuale utente

Blastrac

Blastrac 1-8DPS30 220V-SP Manuale utente

Blastrac

Blastrac 1-15DS Manuale utente

Blastrac

Blastrac 1-8DPF40 Manuale utente

Blastrac

Blastrac 500 E Global Manuale utente

Blastrac

Blastrac BMR-25P Manuale utente

Manuali Attrezzature industriali popolari di altre marche

ABB

ABB Unifix AD Manuale

Mark 7

Mark 7 Evolution Manuale utente

Husky

Husky HyPET Manuale utente

bora

bora PM-1800 Manuale utente

Grizzly

Grizzly T32428 Manuale utente

Siemens

Siemens 8MF1 Series Manuale utente

ABB

ABB HT610965 Manuale utente

ABB

ABB SafeLink Manuale utente

Phoenix

Phoenix PHX-150 Manuale utente

ABB

ABB A165-L32 Manuale utente

ABB

ABB HT842936 Manuale utente

Rioned

Rioned UrbanJet Manuale utente

Hermetica

Hermetica 10 Series Manuale utente

HORNER

HORNER OEE Solution Manuale utente

Hammerhead

Hammerhead HG375 Manuale utente

SCHUNK

SCHUNK VERO-S NSE-A3 138 Istruzioni utente

ABB

ABB HT566657 Manuale utente

Webasto

Webasto GSE CAN Manuale utente