Bluescience UV-c Manuale utente
UV AIR DISINFECTION SYSTEM
700mm LED KIT
UV AIR DISINFECTION SYSTEM
KILLS
VIRUSES
NEUTRALISES
ODOURS
UV
LIGHT
INSTALLATION INSTRUCTIONS
UV-c is scientifically proven to kill 99.9% of viruses and
bacteria, destroying their DNA through germicidal irradation.
UV AIR DISINFECTION SYSTEM
BlueScience UV-c Technology has been developed to provide an
easy retrofit system for all existing air-conditioning equipment to
treat and protect the air, by constant disinfection, every time it
passes through the unit.
After decades of proven use, UV-c disinfection already makes
safe the water we drink and the food we eat. Through the process
of germicidal irradiation, the UV-C light attacks the DNA/DNR of
micro-organisms, killing 99.9% and rendering bacteria and
viruses harmless and unable to reproduce or spread. Recent
research points to similar effectiveness in killing Coronaviruses.
Advances in high-efficiency LED technology now allows the very
air we breathe to be purified and made safe by the same powerful
UV-C light.
Huge health concern over airborne transmission of viruses make
a compelling case to upgrade to BlueScience UV-c, so that we
may all breathe easy and safely.
Below Drip Tray Inside ducting Above Celing
SAFETY INFORMATION / UV WARNINGS
IN THE BOX
INSTALLATION
4
5
6
UV PPE EQUIPMENT 9
UV AIR DISINFECTION SYSTEM
3
Warning: Exposure to direct LED UV light may be harmfull.
Warning: Always protect eyes and skin from UV LEDs.
Warning: Never look directly into UV LEDs during operation.
Warning: Disconnect before servicing.
Warning: After installation, all UV light should remain internal within the casing.
Warning: Ensure no UV light is visible from outside the casing.
Warning: High intensity ultraviolet light.
Warning: All LED lifepans can vary, for optimisation replace LED’s EVERY 12 MOTNHS.
4
Warning: The appliance must be installed in accordance with national wiring regulations.
Warning: Mains power supply must be isolated prior to carrying out any electrical work.
All-pole disconnection from mains must be incorporated in the fixed wiring.
Warning: The supply cord cannot be replaced. If damaged the appliance must be replaced.
Warning: The external accessories must be used only with the appliance provided by
the manufacturer.
Warning: The power supply mains system must be provided with an ‘all-pole disconnection’
device connected directly to the supply terminal that providing a full disconnection
under overcoltage category III.
Warning: This appliance requires no maintenance.
Warning: This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of
the appliance in a safe way and understand the hazards involved.
Warning: Children shall not play with the appliance.
ELECTRICAL WARNING
UV WARNING
5
6
LED Driver
500mm Extension Cable
700mm UV-c LED Strip
AC Unit Safety Seal
Storefront Protector Sticker
Installation Guide
1.
2.
3.
4.
5.
6.
3
6
2
1
5
4
5
6
Connect the mains cable from the LED Driver (Input) into to the AC unit live feed so that power is suppled
when the AC unit is on, this should be done by a qualified electrician.
Mount the LED Driver where
suitable, if it does not fit
below the drip tray
suggested places are in any
plastic ducting that covers
the fridge pipes to the AC
unit, or in the ceiling void
above it.
Remove the CoverIsolate the power to the AC unit
STEP 1
STEP 3
STEP 4
STEP 2
7
If required, UV-c LED Strip can be cut to a desired
length. Cuts can only be made at the terminal point
seen after each UVC LED labelled ‘LED 3’, peel back
the adhesive strip and fix the UV-c LED strip into place.
Lay the UV-c LED Strip on the top of the evaporating coil, making sure the UV-c LED’s are facing in
towards the unit. UV-c LED’s must not radiate out or point out in the direction of the room.
Connect the UV-c LED strip and add date of
installation to the tag. Note: it is important
for you or any other Engineers to be able to
identify the age of the UV-c LED!
Route the cables from the LED Driver (Output)
through the AC unit making sure they are free
from any moving parts and will not obstruct
the casing being re-fitted. The cable should
be routed to sit at the top of the evaporator
coil close to the ‘air in’ side.
STEP 5
STEP 6
STEP 7
STEP 8
8
Apply storefront protector window sticker
at the main entrance of the building.
Apply BlueScience seal to the unit –
to ensure the safety of fellow Engineers.
Using a UVC Meter at a distance of
300mm check in 6 places for readings.
Once a zero reading has been recorded
around the unit protective eyewear and
clothing can be removed. 3
456
Ensuring the filter door is shut, switch power back on and run
AC unit. Protective eyewear and skin coverings are required
from this point.
Refit cover.
STEP 9
STEP 13
STEP 12
STEP 11
STEP 10
9
UV PPE EQUIPMENT
UV AIR DISINFECTION SYSTEM
UV PPE FROM
Protective Eyewear
Gloves
UV-c Meter
AVAILABLE FROM
www.charlesausten.com
KILLS
VIRUSES
NEUTRALISES
ODOURS
UV
LED’s
UV AIR DISINFECTION SYSTEM
Indice
Altri manuali Bluescience Attrezzature da laboratorio
Manuali Attrezzature da laboratorio popolari di altre marche
Agilent Technologies
Agilent Technologies 5800 ICP-OES Manuale utente
Endress+Hauser
Endress+Hauser Cleanfit CPA875 Manuale utente
NI
NI PXI-5422 Manuale
Collomix
Collomix Aqix Manuale utente
SPEX SamplePrep
SPEX SamplePrep 6875 Freezer/Mill Series Manuale utente
Ocean Insight
Ocean Insight FLAME-NIR+ Manuale utente
