BlueTrek X3 Manuale utente

User Manual

“Vol -”button

“Talk” button

“Vol +”button

English

1 I BLUETREK X3

Before using your headset for the ﬁrst time

-You must charge it continuously for about 4 hours, until the red indicator light turns off.

Please refer to the “Charging the BLUETREK® X3®”section of this manual.

-Pair the headset with a mobile phone. Please refer to the “Pairing the BLUETREK® X3”

section of this manual.

Introduction

The BLUETREK® X3 headset is a wireless headset based on the Bluetooth® technology. It com-

plies with Bluetooth® 2.0 protocol, supporting Headset and Hands-free proﬁle.

The BLUETREK® X3 headset has 3 buttons:

·“TALK” button (main button)

·“Vol +”button

·“Vol -”button

English

BLUETREK X3 I 2

Charging the BLUETREK® X3

Please connect the charger to the headset and to the main. During the charge, the

indicator light is red.The indicator light will turn off when the charge is complete.

During subsequent charges, the charging should take approximately 3 hours.

When you hear a low-tone beep in your headset at regular intervals, and the indica-

tor light ﬂashes in red, your headset needs to be recharged.

English

3 I BLUETREK X3

Important:

• If your headset is fully charged, the red indicator light will not turn on when plugging into

the charger.

• To maximize battery lifetime, it is recommended to recharge your headset to full capacity

only when the battery is low, since a battery has a lifetime of about 500 charging cycles.

• If you leave your headset battery empty for an extended period of time, it could excessively

discharge the battery. In this case, charge your headset for 2 hours or more until the battery

recovers and recharges completely.When you ﬁrst charge the headset after prolonged stor-

age, it may take few minutes for the red indicator light to turn on.

• Do not charge your headset for more than 10 hours.

• The use of any other charger will automatically suspend the warranty. It is strictly forbidden

and can be very dangerous.

English

BLUETREK X3 I 4

Switching the BLUETREK® X3 ON and OFF

Switching BLUETREK® X3 ON

When your headset is off, press and hold the TALK button for about 3 seconds until the blue

indicator light is on. A beep (2 tones) can be heard in the speaker.

Release the TALK button.

Switching BLUETREK® X3 OFF

When your headset is on, press and hold the TALK button for about 7 seconds until the red

indicator light is on. A beep (2 tones) can be heard in the speaker then release the TALK

button.

Pairing the BLUETREK® X3

Before using the BLUETREK® X3 headset, you must pair it with your

Bluetooth® mobile phone.

Pairing is the process of linking 2 Bluetooth® devices, so that they

can communicate.

To initiate pairing:

Place the BLUETREK® X3 and your mobile phone within 0.3

meter (1 foot) from each other.

Switch on your phone and select its Bluetooth® discover mode

(refer to the Bluetooth® mobile phone user manual).

Connect

Assign short name

Set as unauthorised

Delete

Select Cancel

“0000”

BLUETREK X3 BLUETREK X3

“Talk” button

BLUETREKX3 BLUETREKX3

English

5 I BLUETREK X3

When the BLUETREK® X3 is switched off, press and hold

the TALK button for about 7 seconds until the indicator light

ﬂashes red and blue alternately. And a sound can be heard

in the speaker.

If you haven’t started the discovery mode within 5 minutes, the headset will go to the standby

mode. You must then switch off your headset and start the pairing again.

If pairing was successful, the indicator light will switch to blue and ﬂashes slowly.

The headset will connect automatically to the mobile phone.

Once the mobile phone detects the headset, a“BLUETREK X3”message will be displayed.

Follow the phone instructions to accept the pairing.The PIN code (or passkey) is 0000, then

press“yes”or“ok”.

For some phones, you may need to select“Connect”.

English

BLUETREK X3 I 6

Making a call

Mobile phone with voice recognition

• Make sure the voice recognition function on your mobile is activated and your voice tags

have been recorded with the phone.To enter these, please refer to your phone’s manual

• When there is no incoming or active call, press once on the TALK button

• Wait for the audio signal sent by the mobile phone (generally a short tone).

• Speak the name of person you wish to call.

Mobile without voice recognition

• Make sure both the headset and the mobile phone are ON and in stand-by mode.

• Dial the number on the phone keypad, after approximately 2 seconds the audio connection

will be established.

Answering a call

When the headset rings, press once on the TALK button to take the call.

Ending a call

Press once on the TALK button to end an active call.

This function may not be available on some phones, please refer to the trouble shooting

frequent asked questions in our website: www.bluetrek.com. to ﬁnd out more.

English

7 I BLUETREK X3

Adjusting the volume

To increase the volume during an active call, press the“VOL+”button on the headset.

To decrease the volume during an active call, press the“VOL-“ button on the headset.

Muting the microphone

To mute the microphone during an active call

During an active call, press and hold the VOL+ button for approximately 3 seconds. A periodic

tone can be heard in the speaker when the microphone is muted.

To end the mute function

When the microphone is muted, quickly press the VOL+ button on the BLUETREK® X3.The

periodic tone will end.

Transferring a call from BLUETREK® X3 to the mobile phone

With a phone in Headset Proﬁle

During an active call, to transfer it to the phone, simply turn off your headset.

With a phone in Hands-Free Proﬁle

During an active call, to transfer it to the phone, press the TALK button for about 2 seconds.

English

BLUETREK X3 I 8

Transferring a call from the mobile phone to the BLUETREK® X3

With a phone in Headset Proﬁle

Switch on your headset.

With a phone in Hands-Free Proﬁle

During an active call on the mobile phone, press the TALK button for about 2 seconds to

transfer the call.

This function may not be available depending on your phone.

Call waiting

When you hear a call waiting alert while you are on a call, press approx. 3 seconds on the

TALK button to accept the second call and place the current call on hold.

To switch between an active call and a hold call, press approx. 3 seconds on the TALK button.

To end the active call and take the hold call, press once on the TALK button.

This function may not be available, depending on your phone. However, you can always

answer the second call from your phone keypad.

XS S*

M* L*

English

9 I BLUETREK X3

Wearing the BLUETREK® X3

Two different sizes of ear hooks are included in the

pack to suit your ear size.

Fitting the Ergobud*

4 different sizes of Ergobud* are included in the pack to

suit your ear size. You can adjust the Ergobud position

that you feel the most comfortable.

To replace the

Ergobud*, remove

the speaker cover by

pulling gently out

from the speaker.

Place the Ergobud*

back onto the speaker

by inserting the

bottom part ﬁrst.

*Registered trademark pending

Altri manuali per X3

Indice

Altri manuali BlueTrek Cuffia

BlueTrek

BlueTrek G2 Manuale utente

BlueTrek

BlueTrek Sense Guida di riferimento

BlueTrek

BlueTrek Sense Manuale utente

BlueTrek

BlueTrek Metal Manuale utente

BlueTrek

BlueTrek Metal Manuale utente

BlueTrek

BlueTrek S21 Manuale utente

BlueTrek

BlueTrek UFO Manuale utente

BlueTrek

BlueTrek Bizz Manuale utente

BlueTrek

BlueTrek MUSICALL Manuale utente

BlueTrek

BlueTrek X2 Manuale utente

BlueTrek

BlueTrek Bizz Manuale utente

BlueTrek

BlueTrek METAL EVOLUTION Manuale utente

BlueTrek

BlueTrek CRESCENDO - Manuale utente

BlueTrek

BlueTrek X3 Manuale utente

BlueTrek

BlueTrek Mini Manuale utente

BlueTrek

BlueTrek CRESCENDO - Manuale utente

BlueTrek

BlueTrek X3 Manuale utente

BlueTrek

BlueTrek CRESCENDO - Manuale utente

BlueTrek

BlueTrek M2 Manuale utente

BlueTrek

BlueTrek Sugar-Clip Manuale utente

BlueTrek

BlueTrek Tattoo Manuale utente

BlueTrek

BlueTrek E2 Manuale utente

BlueTrek

BlueTrek METAL EVOLUTION Manuale utente

BlueTrek

BlueTrek Sugar Manuale utente

Manuali Cuffia popolari di altre marche

Sena

Sena SMH10 Manuale utente

IASUS

IASUS Stealth IA-NT4-BASIC-BT Manuale utente

Sennheiser

Sennheiser EPOS ADAPT 230 Manuale utente

Doro

Doro Flexus HS2005 Manuale utente

GE 98971 Manuale utente

Hama

Hama 00184070 Manuale utente

Plantronics

Plantronics Blackwire 3200 Series Manuale utente

Blue Tiger

Blue Tiger Advantage PLUS Manuale utente

Jawbone

Jawbone Icon Manuale utente

Jabra

Jabra FR 20 Manuale utente

Roxcore

Roxcore Flow A+ Manuale utente

Turtle Beach

Turtle Beach XP 510 Manuale utente

Philips

Philips SHB6101 Manuale utente

Jabra

Jabra PRO 9460 Duo Manuale utente

HyperX

HyperX HyperX Cloud Flight Manuale utente

Bose

Bose MIE2 Mobile Manuale utente

Jabra

Jabra Steel Manuale utente

HyperX

HyperX cloud ii Manuale utente