BLUM SERVO-DRIVE uno Manuale utente

by Blum

www.blum.com

uno

SERVO-DRIVE

Installation instructions

Table of contents

Using the installation instructions��3

Intended use ��3

Safety ��4

Structural changes and spare parts ��6

Disposal ��6

Blum plug-in transformer safety distance ��7

Troubleshooting ��7

Overview drawing ��8

Function ��8

Assembly��9

Adjustment ��9

Blum distance bumper��10

Cabling overview drawing��10

Blum plug-in transformer assembly��10

Cable diagram��10

Start-up ��12

Cover cap assembly ��16

Replacing the SERVO-DRIVE switch battery��16

Removal ��17

Using the installation instructions

Please read the installation instructions and safety information before

SERVO-DRIVE start-up�

We recommend that you use the orientation diagram for easier identi-

fication of the parts being described�

These installation instructions can be used for the SERVO-DRIVE

electric motion support system for AVENTOS HF, AVENTOS HS,

AVENTOS HL and AVENTOS HK�

However, only AVENTOS HF is shown as an example in the illustra-

tions�

Please see the special AVENTOS installation instructions for the

assembly steps for the mechanical AVENTOS HF, HS, HL and HK

fittings without SERVO-DRIVE�

Intended use

SERVO-DRIVE supports the opening and closing of lift systems and

may only be used under the following conditions:

• in dry, enclosed rooms

• in combination with AVENTOS lift systems from Julius Blum GmbH

within the permitted technical specifications

• in combination with a Blum plug-in transformer�

➢The total cable length of 2 metres must not be exceeded�

NOTE

Safety

SERVO-DRIVE complies with current safety standards�

Nevertheless, there are certain risk factors if these installation instruc-

tions are not followed� Please be aware that Julius Blum GmbH is not

responsible for incidental or consequential damages that may arise if

these installation instructions are not followed�

• All national standards must be followed for SERVO-DRIVE assem-

bly� This includes, in particular, those related to the mechanical

safety of moving parts and electrical cabling�

• Only qualified technicians may install and replace Blum compon-

ents, modify the position of the Blum plug-in transformer or modify

any cabling�

• The device may only be connected to a power supply, the voltage,

type of power and frequency of which correspond to those listed on

the rating plate (see Blum plug-in transformer)�

• The outlet must be freely accessible�

• Maintain the safety distances to the Blum plug-in transformer that

are listed in the installation instructions�

• Make sure that there can be no ingress of moisture into the Blum

plug-in transformer and drive unit�

• Before starting repair or maintenance work, switch off the outlet

to which the Blum plug-in transformer is connected or pull out the

mains plug�

• The drive unit, Blum plug-in transformer and SERVO-DRIVE switch

should only be cleaned with a damp cloth because ingress of mois-

ture and aggressive cleaning materials

can damage the electronics�

• Do not touch the area around the lever during the opening and

closing motion�

• No damaged parts should be used�

• Sharp edges may damage the cables�

• Neither the Blum plug-in transformer nor any cabling should come

into contact with moving parts�

• Never take apart a drive unit or a SERVO-DRIVE switch�

• Only one drive unit may be used per Blum plug-in transformer�

WARNING

Danger of death from electric shock!

➢Never open a Blum plug-in transformer�

WARNING

There is a danger of injury if the lever springs

upwards.

There is a danger of injury from the lever springing

upwards when the front is removed�

➢Do not push down on lever arm, remove it

instead�

➢Do not connect the plug-in transformer to the

power supply while the fronts are unattached�

Warning signs and danger symbols

WARNING indicates a danger that could lead to

death or serious injury if not avoided�

This NOTE sign indicates information that

should be observed�

WARNING

NOTE

Structural changes and spare parts

Structural changes and replacement parts not approved by the ma-

nufacturer affect the safety and functionality of SERVO-DRIVE and

are, therefore, not allowed�

• Only use original spare parts from Julius Blum GmbH�

• Blum components designed for this purpose are the only devices

that should be connected to the Blum plug-in transformer�

• The cable from the plug-in transformer to the drive unit may not be

extended�

Disposal

• All SERVO-DRIVE electronic components, including batteries,

should be disposed of in a separate collection for electrical and

electronic appliances as per local regulations�

Blum plug-in transformer safety distance

Troubleshooting

For troubleshooting information, please go to:

www�blum�com/sd/troubleshooting

➢The dimensions in the drawing take into account the safety

distance�

NOTE

A safety distance of 30 mm must be maintained for air circulation;

otherwise, there is a risk that the Blum plug-in transformer

could overheat�

12 3 47

Overview drawing

Lift mechanism

Telescopic arm or lever arm

Drive unit with LED display

Cover cap

SERVO-DRIVE switch with battery display

Blum plug-in transformer with LED display

Blum distance bumper

Front

Cabinet

Electric motion support system

The SERVO-DRIVE switch triggers the automatic opening and closing action of SERVO-DRIVE for

AVENTOS�

Press on the front

➢the lift system opens automatically�

Press on the SERVO-DRIVE switch

➢the lift system closes automatically�

The lift system can be opened or closed manually without restriction without damaging

SERVO-DRIVE for AVENTOS�

Manual operation

➢Manual opening of the lift system by

moving it upwards�

➢Manual closing of the lift system by mo-

ving it downwards�

Function

✓✓

75°

pp

NBY

AVENTOS HF / HS / HL / HK

AVENTOS HF / HS / HL AVENTOS HK

Distribution cable assembly and connecting node assembly

Drive unit adjustment

SERVO-DRIVE for AVENTOS

Drive unit assembly

➢Before SERVO-DRIVE for AVENTOS assembly, the lift mechanisms

must be set so that the front remains open in different positions�

➢If required, install the opening angle stop only after drive unit assembly

and before the reference run�

NOTE

➢The telescopic arm and/or lever arms must be in the completely open

position for drive unit assembly�

DMJD

✓

AVENTOS HF / HS / HL

AVENTOS HK

SERVO-DRIVE switch assembly

➢The drive unit can only be locked when the orange slide is no longer

visible in the view window�

NOTE

The drive unit can only be locked when the drive unit is inserted completely into the lift mechanism�

Altri manuali per SERVO-DRIVE uno

Indice

Altri manuali BLUM Sistema di sollevamento

BLUM

BLUM SERVO-DRIVE Manuale