BOB INFANT CAR SEAT ADAPTER Manuale utente

Tray

Sharp Screw 2x

Pivot Screw 2x

Pivot Plug 2x

Pivot Nut 2x

Restraint

Belt F

Restraint

Belt M

Arm

Accessory Bar

Short Screw

(installed)

Long Screw

(installed)

Long Screw (installed)

Short Screw

(installed)

Main Bar

Arm

Car Seat Compatibility

BOB Stroller Model Year Compatibility

Model Year(s) Model Serial Number

2005 and newer Sport Utility Stroller AA000001 and higher

2005 and newer Sport Utility Stroller D’Lux AB000001 and higher

2005 and newer Ironman AC000001 and higher

2005 and newer Revolution AF000001 and higher

2005 and newer Stroller Strides AG000001 and higher

2007 and newer Revolution 12” AK000001 and higher

TAKE TIME - READ AND UNDERSTAND INSTRUCTIONS COMPLETELY!

Before attempting to assemble or use your new ICSA, read and understand these assembly

instructions completely, as well as the warnings at the end of this document, to insure proper

assembly and safe operation.

If you are unclear on any point, contact your dealer or BOB before use.

Infant Car Seat

Adapter Instructions

TOOLS NEEDED:

Phillips screwdriver.

Congratulations on your

purchase of the BOB Infant

Car Seat Adapter (ICSA).

It is designed to allow the

attachment of an Infant

Car Seat to your BOB

Stroller. Please refer to the

tables at right for details

of compatible strollers and

car seats.

Brand Model Year(s)

Britax® Companion® 2003 and newer

Graco® Snug Ride® 2003 and newer

Graco® SafeSeat™ 2006 and newer

Peg Pérego® Primo Viaggio® 2003 and newer

Peg Pérego® Primo Viaggio SIP™ 2006 and newer

OMA09D P1

Pivot

Bracket

Rotate arms into an

upright position.

POSITION ARMS

ATTACH MAIN BAR

INSTALL PIVOT NUT TIGHTEN PIVOT NUT

Use a Phillips

screwdriver to tighten

pivot screw clockwise,

while holding pivot nut.

Reach under fabric seat.

Thread pivot nut onto

pivot screw as shown.

REPEAT STEPS 8 AND 9

FOR OTHER SIDE.

ASSEMBLE SCREW, PLUG AND BAR

Insert one pivot screw through one end of main bar

and into pivot plug.

POSITION ICSA

Slip pivot plug into

opening on pivot

bracket and push

pivot screw ush

against bar.

Holding pivot screw and

pivot plug in place with

hand, position ends of main

bar over pivot brackets.

INSERT PIVOT

PLUG AND SCREW

Pivot

Bracket

INSERT PIVOT PLUG

ON OPPOSITE SIDE

Slip pivot plug

under end of

main bar and

into opening on

pivot bracket.

Pivot

Bracket

INSERT PIVOT SCREW

Insert pivot screw

through main bar,

pivot plug and into

opening on pivot

bracket.

Pivot Plug

Pivot Screw

Main Bar

SET PARKING BRAKE. See the “Parking Brake” section of your stroller owner’s manual.

OMA09D P2

Extend canopy to expose

lower fabric screw. Remove screw with

Phillips screwdriver,

exposing fabric

grommet and

rivet nut.

Repeat on other side.

INSERT SHARP SCREW

ATTACH RESTRAINT BELT M/F AND ARMS

LOCATE FABRIC SCREWS REMOVE FABRIC SCREW

Insert sharp screw through end of

arm, restraint belt grommet, fabric

grommet and into rivet nut.

Note:

If screw does not turn easily,

unscrew and start again.

Position arm between canopy and frame.

POSITION ARM

TIGHTEN SHARP SCREW

Tighten rmly with

Phillips screwdriver.

Red pull ring

should face out.

ATTACH RESTRAINT BELT M

POSITION RESTRAINT BELT M

Slide restraint belt M grommet between

end of arm and fabric grommet.

Align arm hole over

fabric grommet

and rivet nut.

OMA09D P3

90°

Hold strap at a 90

degree angle.

POSITION CANOPY

Position canopy

against handle bar.

UNBUCKLE

RESTRAINT BELT

Unbuckle restraint belt.

Place ends outside seat.

PREPARE STROLLER FOR INFANT CAR SEAT INSTALLATION

SET PARKING BRAKE

See the “Parking Brake”

section of your stroller

owner’s manual.

INSERT SHARP SCREW

Insert sharp screw through end of

arm, restraint belt grommet, fabric

grommet and into rivet nut.

Note:

If screw does not turn easily,

unscrew and start again.

POSITION ARM

TIGHTEN SHARP SCREW

Tighten rmly with

Phillips screwdriver.

POSITION RESTRAINT BELT F

Slide restraint belt F

grommet between end of

arm and fabric grommet.

BUCKLE BELT

ATTACH RESTRAINT BELT F

Position arm between canopy

and frame.

Align arm hole over fabric

grommet and rivet nut.

Connect restraint belt F

to restraint belt M.

OMA09D P4

90°

Hold strap at a 90 degree angle.

TO REMOVE Britax®

Go To

Pull on red ring

to tighten.

TIGHTEN RESTRAINT BELT

Be sure restraint belt tension is not

constricting child as it may cause

serious injury.

DOUBLE CHECK CAR SEAT IS SECURELY ATTACHED

Warning

Pull car seat upward without

removing restraint belt.

You should not be able to

remove car seat without

unfastening restraint belt.

Warning

Failure to securely attach

car seat may result in

serious injury or death.

INSTALL INFANT CAR SEAT

When installing car seat in the ICSA for the rst time, test t with

the car seat unoccupied to ensure you understand the process.

Installing occupied Infant Car Seat on ICSA for rst time may result

in accident, serious injury or death.

Warning

Fasten restraint belt over top

of infant car seat as shown.

FASTEN RESTRAINT BELT

Britax®

Move car seat

handle into upright

carrying position.

RAISE HANDLE

ENGAGE CAR SEAT

LOWER SEAT BACK

Lower seat back 7” to 8”.

See “Reclining Seat”

section of your stroller

owner’s manual.

Slide grooves on

underside of car seat

onto ICSA accessory bar.

POSITION

CAR SEAT

Place car seat

“rear facing” onto

ICSA accessory

bar, in a straight

downward

motion.

OMA09D P5

Britax®Go To Peg Pérego®Go To Graco®Go To

FASTEN RESTRAINT BELT

ENGAGE CAR SEAT

Peg Pérego®

TO REMOVE

Peg Pérego®

Go To

Be sure restraint belt tension is not

constricting child as it may cause

serious injury.

Warning

Pull on red ring to tighten.

TIGHTEN RESTRAINT BELT DOUBLE CHECK CAR SEAT

IS SECURELY ATTACHED

Pull car seat upward without

removing restraint belt.

You should not be able to

remove car seat without

unfastening restraint belt.

Warning

Failure to securely

attach car seat may

result in serious injury

or death.

Fasten restraint belt

over top of infant car

seat as shown.

Slide grooves on

underside of car

seat onto ICSA

accessory bar.

Move car seat handle

into upright carrying

position.

POSITION HANDLE

Place car seat

“rear facing”

onto ICSA

accessory bar,

in a straight

downward

motion.

POSITION CAR SEAT

RAISE SEAT BACK

See the “Reclining Seat”

section of your stroller

owner’s manual.

OMA09D P6

ENGAGE CAR SEAT

Fasten restraint belt over top of

infant car seat as shown.

FASTEN RESTRAINT BELT

RAISE SEAT BACK REMOVE ACCESSORY BAR

Using a Phillips screwdriver,

remove both screws.

Move car seat handle into

upright carrying position.

POSITION HANDLE

Graco®

POSITION CAR SEAT

Place car seat “rear

facing” onto ICSA

main bar, in a straight

downward motion.

Red hook on Graco®

should be under

main bar.

Slide grooves on underside of

car seat onto ICSA main bar.

TIP: Attach short screws to

accessory bar for future use.

CAUTION: Ends of accessory bar are sharp!

See the “Reclining Seat”

section of your stroller

owner’s manual.

OMA09D P7

Pull on red ring to tighten.

TIGHTEN RESTRAINT BELT

TO REMOVE Graco®Go To

Be sure restraint

belt tension is not

constricting child as it

may cause serious injury.

Pull car seat upward without removing

restraint belt.

You should not be able to remove

car seat without unfastening restraint belt.

DOUBLE CHECK CAR SEAT

IS SECURELY ATTACHED

Failure to securely attach car seat

may result in serious injury or death.

UNFASTEN RESTRAINT BELT

Unfasten restraint

belt. Place ends

outside seat.

With car seat handle

in upright position,

lift car seat straight

up and o ICSA bar.

Fasten restraint belt

when not in use.

SET PARKING BRAKE

See the “Parking Brake”

section of your stroller

owner’s manual.

FASTEN RESTRAINT BELT

Britax®

Peg Pérego®

Graco®

With car seat handle

in upright position,

squeeze red release

button under Graco®

car seat canopy, lift

car seat straight up

and o ICSA bar.

TO REMOVE CAR SEAT

REMOVE CAR SEAT

OMA09D P8

REMOVE ACCESSORY BAR

TRAY INSTALLATION

REMOVE SCREWS

Using a Phillips screwdriver,

remove long screws from tray.

SECURE TRAY

Insert long screw through each hole in tray,

main bar and into nut on underside of tray.

Tighten rmly with Phillips screwdriver.

ROTATE TRAY

Rotate tray towards stroller seat

until it rests on main bar.

Hook tray onto

main bar.

ENGAGE TRAY

Children should not be

placed directly in the

BOB Stroller seat with

the ICSA installed, unless

tray is installed for

safety and protection.

Line up holes.

Using a Phillips screwdriver,

remove both screws.

TIP: Attach short screws to

accessory bar for future use.

CAUTION: Ends of accessory bar are sharp!

OMA09D P9

Position arm between

canopy and frame.

Align arm hole over

fabric grommet and

rivet nut.

Position arm

between canopy

and frame.

Align arm hole over

fabric grommet and

rivet nut.

REMOVE SHARP

SCREW AND BELT

Using a Phillips

screwdriver, remove

sharp screw and

restraint belt M.

REMOVE RESTRAINT BELT M

REPLACE SHARP SCREW

POSITION ARM

Insert sharp screw

through end of arm,

fabric grommet and

into rivet nut.

Note:

If screw does not

turn easily, unscrew

and start again.

Tighten rmly with

Phillips screwdriver.

TIGHTEN SHARP SCREW

REMOVE SHARP

SCREW AND BELT

REMOVE RESTRAINT BELT F

REPLACE SHARP SCREW

POSITION ARM

Insert sharp screw

through end of arm,

fabric grommet and

into rivet nut.

Note:

If screw does not

turn easily, unscrew

and start again.

Tighten rmly with

Phillips screwdriver.

TIGHTEN SHARP SCREW

Using a Phillips

screwdriver, remove

sharp screw and

restraint belt F.

OMA09D P10

Altri manuali per INFANT CAR SEAT ADAPTER

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali BOB Passeggino

BOB

BOB DUALLIE Manuale utente

BOB

BOB REVOLUTION SE Guida all'installazione

BOB

BOB DUALLIE Manuale utente

BOB

BOB SPORT UTILITY STROLLER Guida all'installazione

BOB

BOB DUALLIE Manuale utente

BOB

BOB Ironman Guida all'installazione

BOB

BOB Revolution Duallie Guida all'installazione

BOB

BOB Sun Shield Manuale utente

BOB

BOB OMS09B Manuale utente

BOB

BOB Revolution Manuale utente

BOB

BOB Revolution Manuale utente

BOB

BOB SPORT UTILITY STROLLER Manuale utente

BOB

BOB SPORT UTILITY STROLLER Manuale utente

BOB

BOB MOTION Manuale utente

BOB

BOB DUALLIE Manuale utente

BOB

BOB Revolution Manuale utente

BOB

BOB Revolution Guida all'installazione

BOB

BOB MA0201 Manuale utente

BOB

BOB Revolution Manuale utente

BOB

BOB REVOLUTION PRO DUALLIE Manuale utente

BOB

BOB DUALLIE Manuale utente

BOB

BOB Revolution Manuale utente

BOB

BOB DUALLIE Manuale utente

BOB

BOB Revolution Duallie Manuale utente

Manuali Passeggino popolari di altre marche

Hauck

Hauck Priya Trioset Manuale utente

CHILDHOME

CHILDHOME CWQDN Manuale utente

Dreamer Design

Dreamer Design Rebound GST Manuale utente

Britax

Britax STEELCRAFT AGILE Manuale utente

Graco

Graco 7427 Manuale utente

Comfort

Comfort COMPASS Manuale utente

OBaby

OBaby Aura Manuale utente

Tutek

Tutek Tirso Manuale utente

Babify

Babify Dual Plus Manuale utente

Graco

Graco Stroller Manuale utente

Special Tomato

Special Tomato Jogger Manuale utente

Chicco

Chicco CORTINA TOGETHER TWO-PASSENGER STROLLER Manuale utente

Otto Bock

Otto Bock Kimba neo Manuale utente

Milly Mally

Milly Mally ROYAL Guida rapida

Hauck

Hauck DUETT 3 PRAM Manuale utente

Nuna

Nuna Pepp Manuale utente

Britax

Britax B2 Manuale utente

Graco

Graco VERB Manuale utente