Bodet Sigma Mod Istruzioni e ricette

Upon receipt, always check the product for damage during shipment. If any is found, you may le a damage

claim with the carrier.

Sigma Mod master clock

SIGMA

Installation and start-up instructions

The document concerns the following products :

907451 Wall Sigma Mod - 110/230V

907452 Wall Sigma Mod - 24V

907453 Rack Sigma Mod - 110/230V

907454 Rack Sigma Mod - 24V

907456 Rack Sigma Mod - 36/72V

BODET SA

BP30001

49340 TREMENTINES

Tél: +33 241 71 72 99

Fax: +33 241 71 72 01

Ref : 606554 ZB

www.bodet-time.com

Table of contents

1) General 5

2) Safety rules 6

PROTECTIONS : 6

3) Description 8

4) Installation 9

4.1 Mechanical installation 9

4.2 Electrical connections 10

5) Installation examples 13

5.1 Setting a 24V time distribution 13

5.2 Setting a DHF time distribution 13

5.3 Programming a RHF circuit 14

5.4 Install an option board 15

5.5 Set a 24V TBT output 15

6) Keypad: Key functions 16

7) Main menu programming 18

7.1 Standby state 18

7.2 User menu 18

7.3 USB loading and backup 19

7.4 Adding DHF receivers 20

7.5 Bank holidays 21

7.6 Access code 21

7.7 Time and date 22

7.8 Dynamic radio 23

7.9 Language 23

7.10 Version 23

8) Programming the circuits 24

8.1 Viewing the circuits 25

8.2 Programming the circuits 25

8.2.1 Add a program step 27

8.2.2 Delete a program step 27

8.2.3 Modify a program step 28

8.3 Deleting a program 28

8.4 Viewing the status of a circuit 28

9) Manual testing of circuits 29

10) Programming in Holidays and Special Day mode 30

11) Technician menu programming 32

11.1 Time synchronisation menu 33

11.1.1 Programmable time changeover 34

11.1.2 Setting the time base 35

11.2 Time output management menu 36

11.3 IP conguration menu 38

11.4 Relay setting menu 39

11.5 RHF circuit function setting menu 40

11.6 Function setting menu 41

11.7 “Delete all programming” menu 42

11.8 CPU software download menu 43

11.9 Factory setting restoration menu 44

12) Priority of execution of programs 45

13) Alarm messages 46

14) Options 48

14.1 Mechanical installation 48

14.2 Option board with 3 AFNOR outputs 49

14.3 Option board with 2 ASCII outputs 50

14.4 Option board impulse // 52

14.5 Option board with 2 serial outputs (24VDC power supply) 53

14.6 Option board with 2 serial outputs (48VDC power supply) 54

14.7 relay option board 56

14.8 Option board with AFNOR input 57

14.9 Three inputs option card 58

15) Technical characteristics 59

Appendix I : NTP programming 61

IP function programming 61

IP network conguration and protocols supported : 63

16 ) What to do if ...? Check that … 64

SIGMA M

Installation and start-up instructions

1) General

The Sigma is a master clock which can be used to control receiver clocks and

heating circuits, lighting, ringing, access at the doors of the building, etc.

The SIGMA has functions which can be programmed from the technician

menu.

On rst installation, it is essential to program the technician menu (see

page 32) before the customer menu.

It is also essential when installing the SIGMA to program the technician

functions in the order in which they appear in the menu.

This product must be installed in a residential, commercial or light industry

environment.

Bodet declines all responsibility in the event of an accident resulting from use

not in accordance with the recommendations of this manual.

CAUTION :

Any modication on the product renders the guarantee null and void.

Checking the equipment:

One SIGMA master clock.

One USB key,

One CD containing the PC software.

The CD supplied with your unit contains a program allowing you to carry out

the programming. The programming can thus be carried out simply on a PC

and transferred via the USB port of the Sigma (see “USB loading and backup”,

page 19).

To verify the model of the master clock,

press the key. SIGMA MOD

2) Safety rules

• Installation and maintenance of this equipment should only be carried

out by qualied personnel.

• If the SIGMA is connected to the 230 V mains power supply, its installation

must comply with the European standard IEC 364 (NFC 15.100 for France).

PROTECTIONS :

• 110-230V version: the mains supply for this device must include a neutral

phase circuit breaker of maximum 6 A C curve, rapidly accessible upstream

from the supply.

• 24V DC version: the SELV 24 V power supply for this device must include a

protection of maximum 6 A.

• 36-72V DC version: the SELV 36-72 V power supply (according to NFC 15-

100) for this device must include a protection of maximum 6 A.

• For the relay circuits, add protections with circuit beakers of maximum 4

A. Indicate on the labels the location of these protections.

• The circuit breaker must be switched off during maintenance operation.

Refer to labels in the product.

• All cables must be attached either to the wall (wall-mounted version) or to

the frame of the cabinet (Rack version) before being connected to the various

terminals strips, to prevent any pulling on these terminal strips. In addition, the

wires of each terminal strips must be attached to each other to maintain the

various isolations if an initial fault occurs.

• The time distribution cables must not run alongside high power mains

cables (to avoid interference with communication between the SIGMA and the

clocks).

• The SIGMA must be attached (to the wall or on its support) before being

switched on.

• The “RACK” models must be mounted in 19” cabinet. These components

will provide mechanical, electrical and re protection (only the front panel may

remain accessible).

• IMPORTANT: before any installation, refer to the “technical

characteristics” paragraph.

• Think of making a backup of your programming on the USB key. In case of

incident (breakdown, thunderstorm…), you will just have to restore the backup

to start the time distribution again.

Caution :

• In case of replacement of the CR2032

battery, it is IMPERATIVE to respect the

polarity following the opposite indications.

• There is risk of explosion if the battery is

replaced by a battery of incorrect type.

• Dispose of used batteries according to the

instructions of the manufacturer.

3) Description

Wall box

A) LCD screen

B) Keypad (see page 16)

C) Alarm indicator light (red

LED)

D) Mains indicator light (green

LED)

E) USB connector

F) Relay output terminal strips

19” Rack

4) Installation

4.1 Mechanical installation

Choose a room with low temperature variations

away from any source of electrical interference

(contactors, motors, etc.).

WALL-MOUNTED version: Unscrew the 2

screws on the front, remove the cover (for the

lower cover, press on the 2 clips (N) and slide

it upwards). Disconnect the at jumpers (Q) (be

careful to connect them the same way round

on reassembly) and attach the SIGMA to the

wall. When your unit is in place, remove the

protective lm on the keypad.

RACK version: Install the rack in its slot in an

electrical bay or cabinet.

4.2 Electrical connections

Connect the cables (mains power supply, impulse line or AFNOR output and

radio synchronisation input, depending on the model) to the corresponding

terminal strips as shown in the gure below.

(*) See page 33, the “Time outputs” menu to set this output (Pulse minute,

½ minute, second 24V or power TBT 24VDC 1A).

(**) Power supply depending on the version of SIGMA master clock.

Meaning of status of LEDs on RJ45 connector :

- The green LED reects network activity.

- The yellow LED indicates the speed of the network:

off=10 Mbps on=100 Mbps.

RACK version: The mains power supply, impulse line and AFNOR output and

radio synchronisation input terminal strips are directly accessible at the rear of

the Rack slide-in unit.

(**) 110 to

230VAC or

24VDC

36/72VDC

Circuit C1

Circuit C2

Circuit C3

GPS input

DCF

radio input

(*) Minute, ½ mn or

second 24V, or SR2-59

Afnor output

DHF output

External input

See the limit

characteristics of

these circuits on

page 59

Attach the wires to each other, near

the terminal strips.

IP connection

Indice

Altri manuali Bodet Orologio

Bodet

Bodet Profil 930 Manuale utente

Bodet

Bodet Cristalys 14 Manuale utente

Bodet

Bodet Cristalys Manuale utente

Bodet

Bodet Profil 750 Manuale utente

Bodet

Bodet Style Mondiale Manuale utente

Bodet

Bodet HMS LED 10 Manuale utente

Bodet

Bodet Profil 730 Manuale utente

Bodet

Bodet DHF/DCF Interface Manuale utente

Bodet

Bodet Profil 930 Manuale utente

Bodet

Bodet Style 7 Date Manuale utente

Bodet

Bodet Profil 960 Manuale utente

Bodet

Bodet Profil 730 Manuale utente

Bodet

Bodet Profil 960 Manuale utente

Bodet

Bodet NTP 947 17x W6 Manuale utente

Bodet

Bodet Cristalys Date Manuale utente

Bodet

Bodet Style 5 Seconde Manuale utente

Bodet

Bodet Cristalys Ellipse Manuale utente

Bodet

Bodet Profil 960 Manuale utente

Bodet

Bodet Style 5 Seconde Manuale utente

Bodet

Bodet Style 5 Seconde Manuale utente

Bodet

Bodet Style 12 Manuale utente

Bodet

Bodet Profil 960 Series Manuale utente

Bodet

Bodet Style 5S Manuale utente

Bodet

Bodet Profil 930 L Manuale utente

Manuali Orologio popolari di altre marche

Silicon Laboratories

Silicon Laboratories SI5324 Manuale utente

Heathkit

Heathkit GC-1005 Manuale utente

Oregon Scientific

Oregon Scientific PRYSMA RMR221P Manuale utente

Andrew O'Malley

Andrew O'Malley DOTKLOK Manuale utente

ALGE-Timing

ALGE-Timing ASC3 Manuale utente

Nixie Clock

Nixie Clock Divergence Meter Manuale utente

La Crosse Technology

La Crosse Technology WS-8256-AL Manuale utente

Mini Gadgets

Mini Gadgets MCPro Manuale utente

Casio

Casio TMR-200 Manuale utente

Progetti

Progetti ILTEMPOSTRINGE Manuale

BVItech

BVItech BV-101 Manuale utente

Progetti

Progetti KALIMERO Manuale

La Crosse Technology

La Crosse Technology WT-3141b Manuale

La Crosse Technology

La Crosse Technology W86531 Manuale utente

Sharp

Sharp SPC900 Manuale utente

La Crosse Technology

La Crosse Technology 404-50447 Manuale utente

Datexx

Datexx DF0063 Manuale utente

LG LEC-005 Manuale utente