Bodine 34R6BXPP Guida utente

07401151.B

www.bodine-electric.com

Bodine Electric Company

Type 34R6BXPP Motors & Gearmotors

AC 3-Phase, Inverter-Duty 230VAC or 460VAC

This apparatus is suitable for use in Hazardous Locations

Class I, Division 1, Groups C & D.

Instructions for Installation and Operation

•

PROOF

IP-66

EX-

www.bodine-electric.com

2www.bodine-electric.com

TABLE OF CONTENTS

This manual contains the basic information needed to install and operate a

Bodine type 34R6BXPP three-phase AC motor or gearmotor that is certiﬁed

for use in Class I Division 1 hazardous locations. This manual does not profess

to cover all details or variations in equipment, nor to provide for every possible

contingency associated with installation, operation, or maintenance. No

warranty of ﬁtness for purpose is expressed or implied. It is the responsibility

of the user to determine whether the installation location is hazardous, and to

what degree it is hazardous. Should further information be desired or should

particular problems arise which are not covered sufﬁciently for the user’s

purpose, the matter should be referred to the Bodine Electric Company.

Important Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Product Speciﬁcations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Step 1: Mount the 34R6BXPP Motor or Gearmotor . . . . . . . . . . . . . . .6

Step 2: Attach a Conduit Outlet Box to the Motor . . . . . . . . . . . . . . . .8

Step 3: Make Electrical Connections . . . . . . . . . . . . . . . . . . . . . . .8

Step 4: Operate the 34R6BXPP Motor or Gearmotor . . . . . . . . . . . . . 12

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Bodine Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

FIGURES

Figure 1a – Dimensions for Standard 34R6BXPP Motor . . . . . . . . . . . 6

Figure 1b – Dimensions for Standard 34R6BXPP-FX Gearmotor. . . . . . . 7

Figure 2 – A Typical Conduit Outlet Box . . . . . . . . . . . . . . . . . . . . 8

Figure 3 – Motor after Conduit Outlet Box Installation . . . . . . . . . . . 8

Figure 4a – Electric Connections –

Thermal Switch with Logic Control to Disable Motor Power . . . 10

Figure 4b – Electric Connections –

Thermal Switch with AC Relay to Interrupt Supply . . . . . . . 10

Figure 4c – Electric Connections –

Thermal Switch with 3 Pole AC Relay to Interrupt Supply . . . 11

RoHS COMPLIANCE

This document certiﬁes that the Bodine Electric type 34R6BXPP motor

and type 34R6BXPP-FX gearmotors are manufactured with materials and

processes that comply with European Directive 2011/65/EU, as amended by

council directive 2015/863/EU, on the Restriction of Hazardous Substances

(RoHS).

www.bodine-electric.com 3

!WARNING

IMPORTANT SAFETY PRECAUTIONS

The use of electric machines, like that of all other utilization of concentrated

power, is potentially hazardous. The degree of hazard can be greatly reduced

by proper design, selection, installation, and use, but hazards cannot be

completely eliminated. The reduction of hazard is the joint responsibility

of the user, the manufacturer of the driven or driving equipment, and the

manufacturer of the machine.

The Bodine type 34R6BXPP motor and 34R6BXPP-FX gearmotor

were designed to meet the requirements of UL 674 and CSA C22.2

No. 145-M2017, electric motors for use in Division 1 Hazardous

Locations. The motor ratings were established for operating temperatures

from -20C to +40C. They have a T4A temperature code rating Reference UL

ﬁle number E318315. These products bear the UL mark shown above.

Please read through this operations manual in detail and observe those

paragraphs with the safety alert symbol.

This indicates a potentially hazardous situation, which,

if not avoided, could result in death or serious injury.

!WARNING/AVERTISSEMENT

• CAUTION–To reduce the risk of ignition of hazardous atmospheres,

disconnect the equipment from the supply circuit before opening. Keep

assembly tightly closed when in operation.

• Leads factory-sealed. Do not disassemble any part of this product as that

will compromise its safety in hazardous atmospheres.

• This product should be installed, inspected, and maintained by a qualiﬁed

electrician only, in accordance with all applicable electrical codes.

• ATTENTION–Pour réduire le risque d’inﬂammation des atmosphères

dangereuses, débranchez l’équipement du circuit d’alimentation avant de

l’ouvrir. Gardez l’assemblage bien fermé lorsqu’il est en fonctionnement.

• Fils scellés en usine. Ne démontez aucune pièce de ce produit car cela

compromettrait sa sécurité dans les atmosphères dangereuses.

• Ce produit doit étre installè, inspecté et entretenu par un électricien

qualiﬁé seulement, conformément avec tous les codes de l’électricité

pertinents.

4www.bodine-electric.com

IMPORTANT

Read this manual completely and carefully before making any connections.

Pay special attention to all warnings, cautions, and safety rules. Failure to

follow the instructions could produce safety hazards, which could injure

personnel or damage the motor, gearmotor, or other equipment. If you

have any doubts about how to connect the motor or gearmotor, refer to the

detailed sections of this manual..

PRODUCT SPECIFICATIONS

The motors are 3-Phase AC induction motors. The 34R6BXPP is a 3-Phase AC

induction motor, available with or without an integral gearbox, and a normally

closed, self-resetting thermal switch attached to the motor windings.

Table 1 lists the speciﬁcations common to all variations of this product. Table

2 lists the speciﬁcations unique to each gear ratio that is offered.

TABLE 1

Parameter

Speciﬁcation

Locations: Hazardous locations Class I, Division 1, Groups C & D, or

unclassiﬁed (non-hazardous) locations.

Temperature Code: T4A or T3C

Horsepower: ¼ HP

Volts: 230 VAC, 3 Phase or 460 VAC, 3 Phase (separate models)

Line Frequency: 60 Hz

Inverter Frequency: 10 – 120 Hz for motors, 10 – 90 Hz for gearmotors

Ambient Temperature: -20C to 40C

Insulation: F8

TABLE 2

LINE VOLTAGE RATINGS INVERTER DUTY RATINGS

Product Type Gear

Ratio

Speed

(rpm)

Torque

(lb-in)

Speed Range

(rpm)

Torque @

60 Hz

(lb-in)

34R6BXPP N/A 1600 9.9 214 – 3259 9.9, VT*

34R6BXPP-FX1 5:1 320 46 43 – 474 46, VT*

34R6BXPP-FX2 10:1 160 89 21 – 237 89, VT*

34R6BXPP-FX2 15:1 107 133 14 – 158 133, VT*

34R6BXPP-FX3 20:1 80 178 11 – 119 178, VT*

34R6BXPP-FX3 30:1 53 267 7.1 – 79 267, VT*

34R6BXPP-FX3 40:1 40 265 5.4 – 59 265, VT*

34R6BXPP-FX3 60:1 27 350 3.6 – 40 350, VT*

34R6BXPP-FX4 120:1 13 350 1.8 – 20 350, CT*

34R6BXPP-FX4 180:1 8.9 350 1.2 – 13 350, CT*

34R6BXPP-FX4 300:1 5.3 350 0.7 – 7.9 350, CT*

* VT = “Variable Torque, CT = “Constant Torque”

www.bodine-electric.com 5

INSTALLATION

This product should only be installed by a qualiﬁed person familiar with its

operation and associated hazards, and knowledgeable about the special

requirements for installation in hazardous locations. The National Electrical

Code (NEC), local electrical and safety codes, and when applicable, the

Occupational Safety and Health Act (OSHA) should be observed to reduce

hazards to personnel and property. NEC section 500 (Hazardous Locations) is

particularly important. See pages 6 and 7 for motor and gearmotor dimensions.