BODYMAX B200 Manuale utente
B200
BODYMAX FITNESS
57 BEARDMORE WAY,CLYDEBANK
G81 4HT
OWNER'S MANUAL
www.bodymaxfitness.com
IMPORTANT SAFETY NOTES
1
There is a risk assumed by individuals who use this type of equipment.
Before beginning this or any other exercise program consult your physician.
This is especially important for individuals over the age of 35 or persons
with pre-existing health problems.
g
adjust beyond the marked
BODYMAX B200 at all times.
If unsure about the correct use for the Bodymax B200, please contact the
store where you purchased the cycle.
EXPLODED 1
2
EXPLORE VIEW
EXPLODED 2
3
Main Frame
Rear Stabilizer
Rear Stabilizer fixed bolts
Front Stabilizer fixed bolts
plastic sleeve .
Plastic end cap
Washer
Front Stabilizer
Fly Wheels Fixed Nut
Washer
bolts
Handlebar
Lock lever for HB and seat
Saddle clamp
Slider's safety stop screw
Seat Post
Saddle slider
Saddle
Lock Lever For Stem & Post
Set Screw
Handlebar Stem
Locking Piece
Pop cover
Plastic Sleeve for H/T and
Left Cover
Nut
Nut
Adjust Knob
Floating Piece
Nut
Round steel plate
Spring
Integrated Plastic Bottle
Axles Adjusting Bolts
Fly Wheels Axle
Spacer
B.B & Fly Wheel Axle's
Floating piece set screw
Nut
Fly Wheel
Lock Nut
1
2
3
3A
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23F/23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
1
1
2
2
4
4
4
1
2
2
4
1
2
1
1
1
1
1
2
2
1
2
2
2
1
1
1
1
1
1
2
1
1
2
1
1
4
1
3
1
3
BODYMAX B200 Parts List
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62L
62R
63
64
65
66
67
68
69
70R/L
71
72
73
74
75
76
77
78
79
80
1
1
1
1
1
1
1
1
1
1
2
1
2
4
4
2
2
1
1
1
1
1
1
2
2
1
4
1
1
13
1
1
4
2
1
2
1
1
1
1
1
Brake pad
Brake pad fixed screw
Bush
Nut
Brake Arm
Spacer
Lift spring
Washer
Stud B
Brake arms fixed Bolt
Washer
Stud A
Transportation wheel
Front Stabilizer End Cap
Bearing 608ZZ
Nut
Bolt
Axle Lock Nut
Dusty Cover
Spacer
B.B Axle
Left Crank
Right Crank
Flange Nut
Plastic cap
Driving Pulley
Spring washer
Belt
Inner Cover
Screw
WPD E-003 seal bearing SPD pedal 9/16" axle .
Outer Chain Cover
Height Adjuster
Washer
Stem locking piece
Saddle stud fix screw
Saddle Rod
Saddle stud's plastic sleeve
Washer
Saddle slider's locking piece
Set screw
5
BODYMAX B200 Parts List
6
STEP 1 FRONT AND REAR STABILIZER
FRONT REAR
1. Attach the Front Stabilizer ( 7 ) to the Main Frame (1) on a flat level
surface floor , using two M8 Dome Bolts ( 3A ) , two M8 Washers (6).
2. Attach the Rear Stabilizer (2) to the Main Frame (1) , using two
M8 X 4" Dome Bolts (3) ,two M8 Washers (6).
3. There are Height Adjuster (72) underneath the Rear End Caps (54)
that need to be adjusted until the bike is totally stable on the floor.
54
72 54
72
7
PEDAL
STEP 2 PEDALS ASSEMBLY
1. Carefully align the thread of the axle on the Right Pedal ( 70R)
( "R" marked on the end of pedal axle ). With threaded hole on
the right crank arm and screw in clockwise by HAND. Tighten
the pedal to the crank arm using a 15mm wrench.
2. Repeat the same procedure for the Left Pedal , but screw the
Left Pedal ( 70L ) in counter-clockwise.
IMPORTANT: First assemble pedals by HAND , not using a wrench.It is
important to match thread exactly. Using a wrench to start the
procedure can easily damage the crank threads. This problem is not
covered under warranty.
8
STEP 3 ASSEMBLE HANDLEBAR AND STEM
1. Insert the Handlebar Stem (20) into the Front tube of the
Main Frame (1) . You will be able to adjust the height
of the Handlebar Stem and then using the pre-installed
Locking Lever (18). If you do not have room to turn the
handle on the locking lever . It can disengage from the
covered screw by simply pulling outward on the handle.
Then place the handle where needed to complete
tightening , release and it will be re-engage with the cover
screw. Remember to not make any adjustment past the
marked safety line.
2. Remove the pre-installed Sliders Safety Screw (14) on the
front of the Handlebar Stem (20) . Then slide Handlebar
(11) into the Handlebar Stem. Re-insert the Sliders Safety
Screw and tighten . This Sliders Safety Screw (14) keeps
the Handlebar from sliding all the way off.
20
9
STEP 4 SADDLE AND SEAT POST ASSEMBLY
1. Insert the Seat Post (15) into the rear tube on the Main Frame
(1) . You will be able to adjust the height of the seat post and
then tighten using the pre-installed Locking Lever (18). If you
do not have room to turn the handle on the Locking Lever. It
can disengage from the covered screw by simply pulling
outward on the handle . Then place the handle where needed
to complete tightening, release, and it will re-engage with the
covered screw. Remember to not make any adjustments past
the marked safety lien.
2. Attach the Saddle (17) to the top Saddle Rod (76) and tighten by
nut (13) . Adjust the Saddle Slider's (16) to your desired position
and tighten by Locking Lever (18).
15
13
17
Indice
Altri manuali BODYMAX Cyclette
BODYMAX
BODYMAX B15 Manuale utente
BODYMAX
BODYMAX B50 Manuale utente
BODYMAX
BODYMAX FXB30 Manuale utente
BODYMAX
BODYMAX RB60 Manuale utente
BODYMAX
BODYMAX CVET2706 Manuale utente
BODYMAX
BODYMAX CVEB2419 Manuale utente
BODYMAX
BODYMAX 80 Manuale utente
BODYMAX
BODYMAX B2 Manuale utente
BODYMAX
BODYMAX 40 Manuale utente
BODYMAX
BODYMAX FXB10 Manuale utente
